Panasonic PT-VW355N / PT-VW355ND / T-VW355NT / PT-VX425N / PT-VX425ND / PT-VX425NT (serv.man2) Service Manual ▷ View online
DIS-17
SECTION 2 DISASSEMBLY PROCEDURES
3.8. Parts location and direction in the lighting case
When mounting or assembling the parts in the lighting case, the parts must be mounted in the speci-
fied location and direction as shown in the figure below.
Note: The parts indicated with (*) are mounted by adhesive, therefore, they cannot be replaced
fied location and direction as shown in the figure below.
Note: The parts indicated with (*) are mounted by adhesive, therefore, they cannot be replaced
individually.
Marker comes this
side up
side up
Marker comes this
side up
side up
Marker
Dichroic mirror (B)
Dichroic mirror (G)
Condenser lens (G/B)
Condenser lens (G/B)
Mirror (R)
Mirror (R)
Relay lens (IN)
Relay lens (IN)
Mirror (B)
*
Relay lens (OUT) *
DIS-18
SECTION 2 DISASSEMBLY PROCEDURES
<Cable reforming>
Reform the cables as shown in the figure below. Place the cables at the original
position after replacing the parts.
position after replacing the parts.
Hook
Hook
Wire band
Wire band
Thermal
fuse
Guide
Hook
Hook
Hook
Guide
Ferrite core
Ferrite core
Ferrite core
Note: Please note the reforming of IRIS cable during repairing,
if the IRIS cable expose as shown in the figure(1),
make sure to reform the IRIS cable under the Main board as shown in the figure(2).
IRIS cable
Fig(1)
Fig(2)
IRIS cable
ADJ-1
SECTION 3 ADJUSTMENTS
CONTENTS
Adjustments
Model No. PT-VW355N
PT-VX425N
SECTION 3 ADJUSTMENTS
1. Adjustment Items and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJ-2
1. 1. Lighting area adjustment
1. 2. Polarizer adjustment
1. 3. EEPROM data transfer
1. 4. Color shading correction / gamma shipment data transfer
1. 5. Serial no. setting
1. 6. Fan voltage adjustment
1. 7. Panel type setting
1. 8. Flicker adjustment
1. 9. White balance adjustment
1. 10. Model no. setting
1. 11. Clog sensor calibration
1. 12. Keystone calibration
1. 13. Camera calibration
2. Software Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJ-27
2. 1. Main CPU Software Update
2. 2. Sub CPU Software Update
2. 3. Network CPU Software Update
(2015-05)
ADJ-2
SECTION 3 ADJUSTMENTS
1. 1. Lighting area adjustment
1. 1. 1. Lighting area confirmation
1. After replacing the condenser lens, check if any shade is visible in the panel display area,
* Make the projection environment as dark as possible, and project the all-white pattern (internal pattern) for this check.
2. If there is vignetting on the screen, adjust the Condenser lens-out position.
* Make the projection environment as dark as possible, and project the all-white pattern (internal pattern) for this check.
2. If there is vignetting on the screen, adjust the Condenser lens-out position.
Lighting area
Effective area
1. Adjustment Items and Procedures
When the following parts are disassembled or replaced, please adjust the items according to the table below.
l
Need to adjust
m
Need to check
Adjustment Item
Replaced Component
Remarks
Con-
denser
lens
Optical
block
Polar
-
izer
[A]-
P.C.B
1.1. Lighting area adjustment
m
Adjust if there are color unevenness on the screen
1.2. Polarizer adjustment
l
l
Adjust if there are the color shading on the screen
1.3. EEPROM data transfer
l
Transfer the data from old [A]-P.C.Board to new one
1.4. Color shading / Gamma
shipment data transfer
l
Transfer the data from old [A]-P.C.Board to new one
1.5. Serial no. setting
l
Not necessary if "1.3. EEPRPM data transfer" is taken
1.6. Fan voltage adjustment
l
1.7. Panel type setting
m
l
Not necessary if "1.3. EEPRPM data transfer" is taken
1.8. Flicker adjustment
l
l*1
*1 Not necessary if "1.3. EEPRPM data transfer" is taken
1.9. White balance adjustment
m
m
1.10. Model no. setting
l
Not necessary if "1.3. EEPRPM data transfer" is taken
1.11. Clog Sensor calibration
l
Not necessary if "1.3. EEPRPM data transfer" is taken
1.12. Keystone adjustment
Not support this function
1.13. Camera calibration *2
l
l
*2 This calibration should be taken when the [CM]-Module, Projection lens or Front cover is replaced.
Click on the first or last page to see other PT-VW355N / PT-VW355ND / T-VW355NT / PT-VX425N / PT-VX425ND / PT-VX425NT (serv.man2) service manuals if exist.