Panasonic PT-RCQ10 / PT-RCQ80 (serv.man3) Service Manual ▷ View online
INF-21
SECTION 1 SERVICE INFORMATION
< RCQ10 / RCQ80 >
3) Page 4
- OPERATING MODE
SPECIAL1
Runtime of light source in [SPECIAL1]
*1
mode
*1: Mode that maintains brightness up to an environ-
ment of 36°C for under the particular used condi-
tion
tion
4) Page 6
SDI Payload information will be added.
[---] is indicated if no information.
- MODE
NO SIGNAL/SD-SDI/HD-SDI/3G-SDI
- TRANSPORT
PROGRESSIVE/INTERLACED
- PICTURE
PROGRESSIVE/INTERLACED
- RATE
23.98/24.00/25.00/29.97/30.00/50.00/
59.94/60.00
- SAMPLING
4:2:2(YPBPR)/4:2:2(YCBCR)/4:4:4(YPBPR)/
4:4:4(YCBCR)/4:4:4(RGB)/4:4:4:4(YPBPR+A)
/4:4:4:4(RGB+A)/4:4:4(XYZ)
- BIT DEPTH
8bit/10bit/12bit
5) Page 7
Displays each device's firmware version.
- DIGITAL LINK VERSION Digital LINK firmware
- FPGA VERSION
FPGA firmware (FPGA2/FPGA3)
- CPLD VERSION
CPLD firmware
- FM VERSION
Formatter firmware
- LD DRIVER VERSION
LD Driver firmware (LD1/LD2)
- POWER VERSION
Power cpu firmware
- EMULATE
Status of EMULATE setting
VERSION
EMULATE version
INF-22
SECTION 1 SERVICE INFORMATION
< RCQ10 / RCQ80 >
6) Page 8
Displays each device's firmware version,bitmap and font data
- MAIN VER.
Main microprocessor firmware
- FPGA VER.
FPGA firmware (FPGA2/FPGA3)
- BMP VER.
Bitmap data
- ENG VER
English font data
- RUS VER.
Russian font data
- KOR VER.
Korean font data
- CHI VER.
Chinese font data
- JPN VER.
Japanese font data
7) Page 9
Displays cooling control information
- TEMP (℃)
Intake air (IN) / Optical module (OPT)
Exhaust air (OUT) / LD1 temperature (LD1)
LD2 temperature (LD2)
- FAN MODE
Fan control mode [TYPE A - TYPE J]
- atm
Atmospheric pressure sensor value [hPa]
- RADIATOR1-3
- DMD
- PW1-2
- POWER
Status of each fan and pump [rpm]
- DRIVER
- EXHAUST1-3
- PRISM
- PUMP1-2
8) Page 10
Displays the luminance sensor interna detected value.
- R.SEG
Red segment : Y / x / y
- G.SEG
Green segment : Y / x / y
- B.SEG
Blue segment : Y / x / y
- Y.SEG
Yellow segment : Y / x / y
INF-23
SECTION 1 SERVICE INFORMATION
< RCQ10 / RCQ80 >
9) Page 11
Displays each LD unit information.
- LD1-1
LD1-1 Number of on times / runtime / status
- LD1-2
LD1-2 Number of on times / runtime / status
- LD2-1
LD2-1 Number of on times / runtime / status
- LD2-2
LD2-2 Number of on times / runtime / status
* Status 0 : Off, 1 : On
10) Page 12 - 13
Displays ON/OFF history log of each light source.
4. [TEST PATTERN] menu
• The following test patterns are added.
- Inverted checker
- Red
- Magenta
- Checker
- Yellow
- Blue
- WOB adjustment (W)
- WOB adjustment (RGG)
- Cyan
- Green
- CW index adjustment
- Convergence
INF-24
SECTION 1 SERVICE INFORMATION
< RCQ10 / RCQ80 >
5. [NETWORK] menu
(1) [DIGITAL LINK LOW POWER] menu is added to the sub menu [NETWORK]
• Setup the power mode of DIGITAL LINK DEVICE in the standby mode.
It is possible to reduce the power consumption in standby mode.
- DISABLE : Normal power mode (Default setting)
- ENABLE : Eco power mode.
* Setup [DISABLE] at the normal use.
(2) [CHANNEL A - D] information is added to [SIGNAL QUALITY] of sub menu [DIGITAL LINK STATUS].
Click on the first or last page to see other PT-RCQ10 / PT-RCQ80 (serv.man3) service manuals if exist.