DOWNLOAD Panasonic PT-RCQ10 / PT-RCQ80 (serv.man3) Service Manual ↓ Size: 35.62 MB | Pages: 116 in PDF or view online for FREE

INF-13

    • Setting of the DYNAMIC GAMMA circuit operation.

    - ON : Enable the Dynamic gamma function. (Default setting)

    - OFF : Disable the Dynamic gamma function.

  • Setting of the 3D Color Management System circuit operation.

    - ON : Enable the 3D Color Management system function. (Default setting)

    - OFF : Disable the 3D Color Management system function.

  • Self-diagnosing information Displays.

① --- Model number
② --- Serial number
------------ Firmware version ------------
③ --- Main microprocessor
④ --- Sub microprocessor
⑤ --- FPGA (FPGA2/FPGA3)
⑥ --- CPLD 
⑦ --- Formatter
⑧ --- Digital Link
⑨ --- LD driver (LD1/LD2)
⑩ --- Power microprocessor
⑪ --- Interface board FPGA

⑫ --- Status of Emulate
------------ DEVICE CHECK ------------
⑬ --- Intake air temperature check (Celsius/Fahrenheit)
⑭ --- DMD temperature check (Celsius/Fahrenheit)
⑮ --- Exhaust air temperature check (Celsius/Fahrenheit)
⑯ --- LD1 temperature check (Celsius)
⑰ --- LD2 temperature check (Celsius)
⑱ --- FPGA temperature check (FPGA2/FPGA3 celsius)
⑲ --- Interface board FPGA temperature check (Celsius)
⑳ --- Power temperature check (NORMAL:OK/HIGH:NG) 
㉑ --- LD1 check (1: normal / 0: abnormal)
㉒ --- LD2 check (1: normal / 0: abnormal)

INF-14

OK : FAN

1111 1111 1111 11

R

A

D

IA

TO

R

3 

--

-

P

W

1 ---

P

W

2 ---

P

OW

ER

 -

--

LD 

D

R

IV

ER 

--

-

E

X

H

AU

ST

3 

---

D

M

D

 ---

E

X

H

AU

ST

1 

---

E

X

H

AU

ST

2 

---

R

A

D

IA

TO

R

2 

--

-

R

A

D

IA

TO

R

1 

--

-

PR

IS

M

 ---

PU

M

P1

 ---

PU

M

P

2 

---

OK : LD1  1 

0

LD

1-

1 -

--

LD

1-

2 -

--

OK : LD2  1 1

LD

2-

1 -

--

LD

2-

2 -

--

LD1-1

LD1-2

LD2-2

LD2-1

EXHAUST3 FAN

EXHAUST2 FAN

EXHAUST1 FAN

RADIATOR1 FAN

POWER FAN

DMD FAN

PRISM FAN

LD DRIVER FAN

PHOSPHOR2 FAN

PHOSPHOR1 FAN

RADIATOR2 FAN

RADIATOR3 FAN

•  Items ⑬ to ㉖ indicates the status of "NG" or "OK". If the "NG" indicates in red, the projector has an abnormal- 

ity now. If the "OK" indicates in red, the projector had an abnormality in the past and operates normally now. 

The item [DEVICE CHECK] also indicates the status as  

same as the above.

• To clear the error status, press the [MENU] button in the 

  SELF CHECK mode, the confirmation window will 

  appear and select [OK] and press the [ENTER] button. 

• This must be done after finishing the repair or maintenance.

CLEAR ERROR INFOMATION ?

OK

CANCEL

EXECUTE

CHANGE

ENTER

㉓ --- Fan check (1: normal / 0: abnormal)
㉔ --- Luminance sensor check (detected value R/G/B/Y)
㉕ --- Atmospheric pressure sensor check (hPa/Celsius)
㉖ --- Angle sensor check (Horizontal angle / Vertical angle)

w

⑯--- LD1 check (1: normal / 0: abnormal)

⑰--- LD2 check (1: normal / 0: abnormal)

⑱--- Fan check (1: normal / 0: abnormal)

INF-15

  • When replaced the phosphor wheel or color wheel, perform automatic adjustment of each wheel rotational phase.

    * Please refer to SECTION 3 (Adjustments) for the procedure.

  • Operation setting of shutter at standby operation.

    - SHUTTER KEEP:  When pushing the standby key while the shutter mode is on, the projector keeps the shutter mode 

on and sets into standby mode.

    - SHUTTER OPEN:   When pushing the standby key while the shutter mode is on, the projector opens the shutter and 

displays the "Power OFF confirmation message". (Default setting)

  • Enables to display the error information of the LIGHT indicators on the screen.

    (It is useful when using the projector with rear projection mode)

    - ON : "LD1/LD2 ERROR" is displayed on the screen  if the lighting error occurs. 

            (It will disappear when any of the control buttons is pressed.)

    - OFF : No message is displayed on the screen if the lighting error occurs. (Default setting)

  • Set the model and destination of this projector after replacing the A-PCB.

    * This model setting is effective after main power restart.

  • Used when checking the light source. (It is not normally used.)

[LIGHT SELECT]

• You can setup the light source to be lit.

    - ALL: All lighting blocks (LD1 / LD2) will light up. (Default setting)

    - LD1: Only the lower side of the lighting block (LD1) will be lit.

    - LD 2: Only the upper side of the lighting block (LD2) is lit.

    * After selection, press the <ENTER> button to switch.

    * When the power is turned off , it returns to "ALL". (Default setting)

[TEST PATTERN]

• Display test pattern (all white) for optical adjustment. (For factory adjustment)

  •   When replacing the LD unit with a new one, reset the LD runtime. 

 This resetting is effective after main power restart.

    * Please refer to SECTION 3 (Adjustments) for the procedure.

  •  Set the extension of black mute time.

   It hides the input switching noise.

    - DISABLE : Does not extend the mute time.  (Default setting)

    - 0.5s --- 5.0s : Extension of mute time can be set in 0.5 second steps.

  • Set this when you want to turn off the indicator LED.

[INDICATOR MODE]

    - NORMAL : Turn on or off the indicator LED according to the projector status.(Default setting)

    - OFF : The indicator will be forcibly turned off.

    - TIMEOUT : The indicator turns off when no operation is taken for a setting time.

[NO ACTIVITY TIME]

    Setup the time to turn off when INDICATOR MODE setting is TIMEOUT.

    You can set the time up to 15 minutes with 1 minute step. (default setting is 15 MIN.)

    *If INDICATOR MODE setting is NORMAL or OFF, this will be grayed out.

 •  Make the rotation phase adjustment of the wheels individually. 

(Do not change the setting, usually.)

INF-16

  •  Set up the communication specifications of the command control.

    - 0SEC : 1 Command 1 session mode. (Default)

    - 30SEC : Keeps a session for 30 seconds.

  • Setup when failing the DIGITAL LINK firmware updating. (Normally not used)

    - 0 : Normal (Default)

    - 1 : Firmware writing mode by the special tool.

  •  At the turning on the projector, setup when the abnormal HDMI signal (no information frame, etc.) is output from source 

equipment, it controls the Hot Plug and outputs the signal again.

    - DISABLE : Hot Plug is "High" during connecting to the source equipment.*1 

    - POWER ON : Hot Plug is switched from "Low" to "High" once when starting up the main power supply. (Default) *1, *2

    *1 :  When changing the setting of "EDID Selection" or "EDID Mode" on the HDMI IN menu, the Hop Plug becomes 

"Low".

    *2 : The source equipment may output the signal again to the connected equipment (monitors, projectors).

  •   Save log data to USB memory via USB port. 

The saved log data can be checked using the log backup tool.

    * Please refer to [5.4.Log acquisition procedure using USB memory] of this section for the procedure.

  •   Adjusts the smooth pixel drive function when the WOB unit is replaced.

    * Please refer to SECTION 3 (Adjustments) for the procedure.

  • Setting of the gradation smooth processing circuit operation.

    - ON : Enable the smooth gradation steps processing. (Default setting)

    - OFF : Disable