Panasonic PT-RCQ10 / PT-RCQ80 (serv.man3) Service Manual ▷ View online
4
PREFACE
< RCQ10 / RCQ80 >
Cautions when installing
r
After attaching the projection lens, be sure to attach the Lens Mount Cover.
Not doing so may cause failure due to accumulating dust internally.
r
r
Do not set up the projector outdoors.
The projector is designed for indoor use only.
r
r
Do not set up the projector in the following locations.
f Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal compo-
nents or malfunction.
f Location close to sea or where corrosive gas may occur: The projector may fall due to corrosion. Also, failure to do so
may shorten the life of the components and result in malfunction.
f Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare cases due to
the heated air from the exhaust vent or the hot or cooled air from the air conditioner. Make sure that the exhaust from the
projector or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
f Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life of the light
source, or result in deformation of the projector due to heat, which may cause malfunctions.
Follow the operating environment temperature of the projector.
f Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
f Places where there is high-power laser equipment: Directing a laser beam onto the projection lens surface causes dam-
age to the DLP chips.
r
The projector may not work properly due to strong radio wave from the broadcast station or the radio.
If there is any facility or equipment which outputs strong radio waves near the installation location, install the projector at
a location sufficiently far from the source of the radio waves. Or, wrap the LAN cable connected to the <DIGITAL LINK>
terminal using a piece of metal foil or a metal pipe which is grounded at both ends.
r
Focus adjustment
The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in the
period just after switching on the power. It is recommended to perform the focus adjustment after 30 minutes have elapsed
with the focus test pattern displayed.
r
Do not install the projector at an altitude of 4 200 m (13 780') or higher above sea level.
r
Do not use the projector in a location that the ambient temperature exceeds 45 °C (113 °F).
Using the projector in a location where the altitude is too high or the ambient temperature is too high may reduce the life of
the components or result in malfunctions.
Do not use the projector in a location where the ambient temperature exceeds 40 °C (104 °F) when the optional Wireless
Module (Model No.: AJ-WM50 Series) is attached to the projector.
r
Projection in all 360° direction is possible.
r
Cautions when setting up the projector.
f The projector can be used by installing its top placed on the floor. To prevent the top surface from getting scratched dur-
ing use, it is recommended to attach about a 20 mm (25/32") square buffer material (such as rubber cushion) on the four
corners of the top surface.
f Use the adjustable feet only for the floor standing installation and for adjusting the angle. Using them for other purposes
may damage the projector.
f When installing the projector with a method other than the floor installation using the adjustable feet, top placed on the
floor, or the ceiling installation with the Ceiling Mount Bracket, use the five screw holes for ceiling mount to fix the projec-
tor to the mount.
In such case, make sure that there is no clearance between the screw holes for ceiling mount on the projector bottom and
the setting surface by inserting spacers (metallic) between them.
f Use a torque screwdriver or Allen torque wrench to tighten the fixing screws to their specified tightening torques.
Do not use electric screwdrivers or impact screwdrivers.
(Screw diameter: M6, tapping depth inside the projector: 12 mm (15/32"), torque: 4 ± 0.5 N·m)
f Do not stack projectors on top of each other.
f Do not block the intake/exhaust vents of the projector.
f Prevent hot and cool air from the air conditioning system to blow directly to the intake/exhaust vents of the projector.
360°
360°
360°
360° vertically
360° horizontally
360° tilted
(combination of vertical and horizontal)
5
PREFACE
< RCQ10 / RCQ80 >
f Do not install the projector in a confined space.
When installing the projector in a confined space, provide air conditioning or ventilation separately. Exhaust heat may ac-
cumulate when the ventilation is not enough, triggering the protection circuit of the projector.
f Panasonic takes no responsibility for any damage to the product caused by an inappropriate choice of location for install-
ing the projector, even if the warranty period of the product has not expired.
Usable outlet
100 mm (3-15/16") or longer
500 mm (19-11/16") or longer
500 mm (19-11/16") or longer
500 mm (19-11/16") or longer
This projector supports AC 100 V to AC 240 V as the power supply. A grounded outlet supporting 15 A is required
with either voltage.
The shape of the usable outlet differs depending on the power supply. Following illustrations are examples.
The shape of the usable outlet differs depending on the power supply. Following illustrations are examples.
2P/3W 15 A 250 V
2P/3W 15 A 250 V
2P/3W 20 A 250 V
2P/3W 15 A 125 V
2P/3W 15 A 250 V
Attention
f
Use the supplied power cord and ground at the outlet.
f
Use the power cord matching the used power supply voltage and outlet shape.
Note
f
The supplied power cords vary depending on the country or region where you purchased the product.
6
PREFACE
< RCQ10 / RCQ80 >
CONTENTS
1. Safety Precautions
1. 1. General Guidelines
1. 2. Leakage Current Check
1. 2. Leakage Current Check
2. Specifications
2. 1 Specifications
2. 2 Connecting terminal / slot
2. 3 Wireless LAN
2. 4 Compatible signal
2. 5. Dimensions
2. 2 Connecting terminal / slot
2. 3 Wireless LAN
2. 4 Compatible signal
2. 5. Dimensions
SECTION 1 SERVICE INFORMATION
1. The name of each part
1. 1. Remote controls
1. 2. Projector body
1. 3. Control panel
1. 4. Connecting terminals
1. 5. Interface Board (optional)
1. 2. Projector body
1. 3. Control panel
1. 4. Connecting terminals
1. 5. Interface Board (optional)
2. Menu Navigation
3. Service Mode
3. Service Mode
3. 1. Setting to Service Mode
3. 2. Resetting to User Mode
3. 3. Functions of Service Mode
3. 2. Resetting to User Mode
3. 3. Functions of Service Mode
4. Notes on service
4. 1. Before service operation
4. 2. Service
4. 3. Installing the Interface Board (optional)
4. 4. Security password
4. 2. Service
4. 3. Installing the Interface Board (optional)
4. 4. Security password
5. Troubleshooting
5. 1. Power/Light source/Temperature indicators
5. 2. Shutdown system
5. 3. Log data acquisition procedure
5. 4. Log data acquisition procedure using USB memory
5. 5. Self-diagnosis information acquisition by control commands
5. 6. System log error code table
5. 4. Troubleshooting
5. 2. Shutdown system
5. 3. Log data acquisition procedure
5. 4. Log data acquisition procedure using USB memory
5. 5. Self-diagnosis information acquisition by control commands
5. 6. System log error code table
5. 4. Troubleshooting
SECTION 2 DISASSEMBLY PROCEDURES
1. Parts Locations
1. 1. Mechanical parts location
1. 2. Optical parts location
1. 3. Electrical parts location (PCBs)
1. 4. Electrical parts location (Fans)
1. 2. Optical parts location
1. 3. Electrical parts location (PCBs)
1. 4. Electrical parts location (Fans)
7
PREFACE
< RCQ10 / RCQ80 >
2. Precautions for disassembly / assembly
2. 1. Before disassembly
2. 2. Removing / inserting procedure of flexible cable
2. 3. WOB unit
2. 2. Removing / inserting procedure of flexible cable
2. 3. WOB unit
3. Disassembly Instructions
3. 1. Top cover removal
3. 2. Side cover (L/R), Front cover, Rear cover removal
3. 3. Signal block removal
3. 4. LD driver block removal
3. 5. Power unit assy removal
3. 6. DMD block removal
3. 7. Rod assy removal
3. 8. Liquid cooling unit 1 / Liquid cooling unit 2 removal
3. 9. LD units removal
3.10. Lighting case 2 / Lighting case 1 removal
3.11. Phosphor Wheel 2 / Phosphor Wheel 1 removal
3. 2. Side cover (L/R), Front cover, Rear cover removal
3. 3. Signal block removal
3. 4. LD driver block removal
3. 5. Power unit assy removal
3. 6. DMD block removal
3. 7. Rod assy removal
3. 8. Liquid cooling unit 1 / Liquid cooling unit 2 removal
3. 9. LD units removal
3.10. Lighting case 2 / Lighting case 1 removal
3.11. Phosphor Wheel 2 / Phosphor Wheel 1 removal
SECTION 3 ADJUSTMENTS
1. Adjustment item and a procedure
1. 1. Focus balance adjustment
1. 2. Lighting area adjustment
1. 3. Lens calibration
1. 4. Wheel index adjustment
1. 5. EEPROM data transfer
1. 6. Model information setup
1. 7. Date and time setup
1. 8. LD unit runtime reset
1. 9. Pixel shift adjustment
1. 2. Lighting area adjustment
1. 3. Lens calibration
1. 4. Wheel index adjustment
1. 5. EEPROM data transfer
1. 6. Model information setup
1. 7. Date and time setup
1. 8. LD unit runtime reset
1. 9. Pixel shift adjustment
2. Firmware update procedure
2. 1. Equipment to be used
2. 2. Connection Preparations
2. 3. Update procedure
2. 2. Connection Preparations
2. 3. Update procedure
3. Firmware update procedure using USB memory
3. 1. Preparing the USB memory
3. 2. Update procedure
3. 2. Update procedure
