Panasonic KV-S2087 (serv.man2) Service Manual ▷ View online
45
8.4.2.
Paper Path Cover
(1) Select Automatic feeding (See 4.1.) to keep the Gate close.
(2) Remove the Feed Tray. (See 8.2.1.)
(3) Remove the DFP Cover.
(4) Remove the DFP Roller.
(5) Remove 4 Screw A.
(2) Remove the Feed Tray. (See 8.2.1.)
(3) Remove the DFP Cover.
(4) Remove the DFP Roller.
(5) Remove 4 Screw A.
(5) Set Gates up at upright position (arrow
1
).
(6) Unlock 2 Hooks to remove the Paper Path Cover.
Reassembling Note :
Before attaching the Paper Path Cover to the Main Unit, set
Gates up at upright position (arrow
Gates up at upright position (arrow
1
).
<Front side>
<Back side>
Hook:
*Make sure that 2 Hooks of the Paper Path Cover
are locked tog
Hther with the Main Chassis.
Paper Path Cover
Main Chassis
A
Hook:
A
DFP Cover
A
A
Gate
1
Paper Path Cover
46
8.4.3.
USR Sensor Board
8.4.4.
Door Sensor Board
8.4.5.
Paper Feed Select Sensor Board
8.4.6.
Paper Sensor
(1) Remove the Paper Path Cover. (See 8.4.2.)
(2) Remove the 2 Screws A and Connector on the Board.
(3) Remove the USR Sensor Board.
(2) Remove the 2 Screws A and Connector on the Board.
(3) Remove the USR Sensor Board.
(1) Remove the Paper Path Cover. (See 8.4.2.)
(2) Remove the Screw A and the Connector on the Board.
(3) Remove the Door Sensor Board.
(2) Remove the Screw A and the Connector on the Board.
(3) Remove the Door Sensor Board.
(1) Remove the Paper Path Cover. (See 8.4.2.)
(2) Remove the 2 Screws A and the Connector on the Board.
(3) Remove the Paper Feed Select Sensor Board.
(2) Remove the 2 Screws A and the Connector on the Board.
(3) Remove the Paper Feed Select Sensor Board.
(1) Remove the Paper Path Cover. (See 8.4.2.)
(2) Remove the Screws A.
(3) Remove the Screw F to remove the Paper Sensor.
(2) Remove the Screws A.
(3) Remove the Screw F to remove the Paper Sensor.
Paper Sensor
F
A
Paper Feed
Select
Sensor Board
Select
Sensor Board
Door Sensor
Board
Board
USR Sensor Board
A
A
A
A
47
8.4.7.
CIS Unit (B)
(1) Remove the Paper Path Cover. (See 8.4.2.)
(2) Press the Hook (A) (arrow
(2) Press the Hook (A) (arrow
1
) to take out the CIS Unit (B)
from the Main Unit (arrow
2
).
(3) Remove the FFC Cable to remove the CIS Unit (B).
(4) Unlock 7 Hooks to separate the CIS Cover (B)
Reassembling Note:
Make sure to lock 7 Hooks properly.
(5) Take out the Scanning Glass (B) A’ssy.
(6) Remove the Screw (C) and Lock spring.
(7) Remove the Reference Plate (F).
(6) Remove the Screw (C) and Lock spring.
(7) Remove the Reference Plate (F).
FFC Cable
CIS(B)
1
Main Unit
CIS (B)
2
(A)
Hook:
Scanning Glass (B) A’ssy
Reference Plate (F)
(C)
CIS (B)
CIS Cover (B)
Lock Spring
48
8.4.8.
Lower Relay Board
8.4.9.
Drive Belt
(1) Remove the CIS Unit (B). (See 8.4.7.)
(2) Remove the 2 Screws B and 3 Connectors on the Board.
(3) Remove the Lower Relay Board.
(2) Remove the 2 Screws B and 3 Connectors on the Board.
(3) Remove the Lower Relay Board.
(1) Remove the Left Cover. (See 8.2.9.)
(2) Loosen the screw. Push down the lever until the belt goes
(2) Loosen the screw. Push down the lever until the belt goes
slack, and then tighten the screws to hold the lever in place.
(3) Remove the Drive Belt.
Reassembling Note: BELT LAYOUT
a: Reattach the Drive Belt as shown in the following figure.
b: Loosen the screw. (Loosening the screw will make the
b: Loosen the screw. (Loosening the screw will make the
belt tighten properly.
c: Check if the belt works properly by turning Gear (A).
d: Tighten the screw.
d: Tighten the screw.
B
Lower Relay Board
B
Connectors
Screw
Drive Belt
Spring
Lever
(A)
Click on the first or last page to see other KV-S2087 (serv.man2) service manuals if exist.