Panasonic WJ-SX550 Service Manual / Supplement ▷ View online
– 42 –
7.8.2. Flow Chart for Alarm Board Check by WV-CU550 or Personal Computer
Start
Turn on the Power Switch of WJ-SX550
Press MON and 2 switches
simultaneously, and Power
Switch to ON; MON and 2
switches are pressed until
displayed as shown on right on
the LCD. (WV-CU550)
simultaneously, and Power
Switch to ON; MON and 2
switches are pressed until
displayed as shown on right on
the LCD. (WV-CU550)
Enter the Check No. 4XX
by 10-key.
by 10-key.
Press GO key
Execute the Check No. 4XX:
During execute, displayed as
shown on right on the LCD.
During execute, displayed as
shown on right on the LCD.
Return to Idle?
YES
NO
Finish?
Turn off the Power Switch
End
YES
∗ ∗ ∗ ∗ ∗ ∗
S
e
l
f C
h
e
c
k
C
h
e
c
k No.
0
0
0 I
D
L
E
SW Description etc.
C
h
e
c
k No.
4
X
X E
X
E
Enter to Idle mode, message
displayed as shown on right on
the LCD.
displayed as shown on right on
the LCD.
C
h
e
c
k No.
499 I
D
L
E
After completion of the Check,
message displayed as shown
on right on the LCD.
message displayed as shown
on right on the LCD.
End
No. 4
X
X O
K
C
h
e
c
k No.
4
X
X I
D
L
E
Next Check?
NO
YES
Next Check?
NO
YES
NO
Turn off the Power Switch of WV-CU550
Note: It is possible to change from the Normal Operation Mode to the
Self Check mode or from the Self Check Mode to the Normal
Operation Mode when control is by the RS-485 line.
Execute the Check No. 499 during execution.
or
Press the ACK RESET key.
– 43 –
7.9. Self Check Procedure for the Alarm
Board
8
Set the Extension Board between the Mother Board and
the Alarm Board.
8
Turn On the Power Switch of the Matrix Switcher WJ-
SX550.
8
Turn Off the Power Switch of the System Controller WV-
CU550.
8
While pressing the MON and 2 Switches simultaneously,
turn on the Power Switch of WV-CU550.
400 Original Setting at Factory
8
Enter the Instruction Code 400 by the 10-key of the WV-
CU550 or Instruction Code 00 by the SW11 on the Alarm
Board.
8
Press the GO key or press the SW2 (TEST) on the Alarm
Board, the original data set at the Factory is loaded.
401 Switch Check (Does not automatic recovery
to Idle mode)
8
Enter the Instruction Code 401 by the 10-key or
Instruction Code 01 by the SW11.
8
Press the GO key or press the SW2.
8
Set the SW1-1 to On, the 7-segment LED on the 7 Seg
Board should be indicated 1
.
1 and the Data “STX SA
000 ETX” is transmitted to the RS-232C line.
8
Set the SW1-1 to Off, the 7-segment LED should be indi-
cated 1 1 and the Data “STX SA 000 ETX” is transmitted
to the RS-232C line.
8
Set the SW1-2 to On, the 7-segment LED should be indi-
cated 1
.
2 and the Data “STX SA 001 ETX” is transmitted
to the RS-232C line.
8
Set the SW1-2 to Off, the 7-segment LED should be indi-
cated 1 2 and the Data “STX SA 000 ETX” is transmitted
to the RS-232C line.
8
Set the SW2 to On, the 7-segment LED should be indi-
cated 2 and the Data “STX SA 002 ETX” is transmitted
to the RS-232C line.
8
Set the SW3 to On, the 7-segment LED should be indi-
cated 3 and the Data “STX SA 003 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-1 to On, the 7-segment LED should be indi-
cated 4
.
1 and the Data “STX SA 004 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-1 to Off, the 7-segment LED should be indi-
cated 4 1 and the Data “STX SA 005 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-2 to On, the 7-segment LED should be indi-
cated 4
.
2 and the Data “STX SA 006 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-2 to Off, the 7-segment LED should be indi-
cated 4 2 and the Data “STX SA 007 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-3 to On, the 7-segment LED should be indi-
cated 4
.
3 and the Data “STX SA 008 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-3 to Off, the 7-segment LED should be indi-
cated 4 3 and the Data “STX SA 009 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-4 to On, the 7-segment LED should be indi-
cated 4
.
4 and the Data “STX SA 010 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-4 to Off, the 7-segment LED should be indi-
cated 4 4 and the Data “STX SA 011 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-5 to On, the 7-segment LED should be indi-
cated 4
.
5 and the Data “STX SA 012 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-5 to Off, the 7-segment LED should be indi-
cated 4 5 and transmit the Data “STX SA 014 ETX” to
the RS-232C line.
8
Set the SW4-6 to On, the 7-segment LED should be indi-
cated 4
.
6 and the Data “STX SA 015 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-6 to Off, the 7-segment LED should be indi-
cated 4 6 and the Data “STX SA 016 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-7 to On, the 7-segment LED should be indi-
cated 4
.
7 and the Data “STX SA 017 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-7 to Off, the 7-segment LED should be indi-
cated 4 7 and the Data “STX SA 018 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-8 to On, the 7-segment LED should be indi-
cated 4
.
8 and the Data “STX SA 019 ETX” is transmitted
to the RS-232C line.
8
Set the SW4-8 to Off, the 7-segment LED should be indi-
cated 4 8 and the Data “STX SA 020 ETX” is transmitted
to the RS-232C line.
8
After completion the check of the SW4, all sections of the
SW4 are reset to the Off positions.
8
Set the SW5-1 to On, the 7-segment LED should be indi-
cated 5
.
1 and the Data “STX SA 021 ETX” is transmitted
to the RS-232C line.
– 44 –
8
Set the SW5-1 to Off, the 7-segment LED should be indi-
cated 5 1 and the Data “STX SA 022 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-2 to On, the 7-segment LED should be indi-
cated 5
.
2 and the Data “STX SA 023 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-2 to Off, the 7-segment LED should be indi-
cated 5 2 and the Data “STX SA 024 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-3 to On, the 7-segment LED should be indi-
cated 5
.
3 and the Data “STX SA 025 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-3 to Off, the 7-segment LED should be indi-
cated 5 3 and the Data “STX SA 026 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-4 to On, the 7-segment LED should be indi-
cated 5
.
4 and the Data “STX SA 027 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-4 to Off, the 7-segment LED should be indi-
cated 5 4 and the Data “STX SA 028 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-5 to On, the 7-segment LED should be indi-
cated 5
.
5 and the Data “STX SA 029 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-5 to Off, the 7-segment LED should be indi-
cated 5 5 and the Data “STX SA 030 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-6 to On, the 7-segment LED should be indi-
cated 5
.
6 and the Data “STX SA 031 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-6 to Off, the 7-segment LED should be indi-
cated 5 6 and the Data “STX SA 032 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-7 to On, the 7-segment LED should be indi-
cated 5
.
7 and the Data “STX SA 033 ETX” is transmitted
to the RS-232C line.
8
Set the SW5-7 to Off, the 7-segment LED should be indi-
cated 5 7 and transmit the Data “STX SA 034 ETX” is
transmitted to the RS-232C line.
8
Set the SW5-8 to On, the 7-segment LED should be indi-
cated 5
.
8 and the Data “STX SA 035 ETX” to the RS-
232C line.
8
Set the SW5-8 to Off, the 7-segment LED should be indi-
cated 5 8 and the Data “STX SA 036 ETX” is transmitted
to the RS-232C line.
8
After completion the check of the SW5, all sections of the
SW5 are reset to the Off positions.
8
Set the SW6-1 to On, the 7-segment LED should be indi-
cated 6
.
1 and the Data “STX SA 037 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-1 to Off, the 7-segment LED should be indi-
cated 6 1 and the Data “STX SA 038 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-2 to On, the 7-segment LED should be indi-
cated 6
.
2 and the Data “STX SA 039 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-2 to Off, the 7-segment LED should be indi-
cated 6 2 and the Data “STX SA 040 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-3 to On, the 7-segment LED should be indi-
cated 6
.
3 and the Data “STX SA 041 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-3 to Off, the 7-segment LED should be indi-
cated 6 3 and the Data “STX SA 042 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-4 to On, the 7-segment LED should be indi-
cated 6
.
4 and the Data “STX SA 043 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-4 to Off, the 7-segment LED should be indi-
cated 6 4 and the Data “STX SA 044 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-5 to On, the 7-segment LED should be indi-
cated 6
.
5 and the Data “STX SA 045 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-5 to Off, the 7-segment LED should be indi-
cated 6 5 and the Data “STX SA 046 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-6 to On, the 7-segment LED should be indi-
cated 6
.
6 and the Data “STX SA 047 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-6 to Off, the 7-segment LED should be indi-
cated 6 6 and the Data “STX SA 048 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-7 to On, the 7-segment LED should be indi-
cated 6
.
7 and the Data “STX SA 049 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-7 to Off, the 7-segment LED should be indi-
cated 6 7 and the Data “STX SA 050 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-8 to On, the 7-segment LED should be indi-
cated 6
.
8 and the Data “STX SA 051 ETX” is transmitted
to the RS-232C line.
8
Set the SW6-8 to Off, the 7-segment LED should be indi-
cated 6 8 and the Data “STX SA 052 ETX” is transmitted
to the RS-232C line.
– 45 –
8
After completion the check of the SW6, all sections of the
SW6 are reset to the Off positions.
8
Set the SW7-1 to On, the 7-segment LED should be indi-
cated 7
.
1 and the Data “STX SA 053 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-1 to Off, the 7-segment LED should be indi-
cated 7 1 and the Data “STX SA 054 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-2 to On, the 7-segment LED should be indi-
cated 7
.
2 and the Data “STX SA 055 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-2 to Off, the 7-segment LED should be indi-
cated 7 2 and the Data “STX SA 056 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-3 to On, the 7-segment LED should be indi-
cated 7
.
3 and the Data “STX SA 057 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-3 to Off, the 7-segment LED should be indi-
cated 7 3 and the Data “STX SA 058 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-4 to On, the 7-segment LED should be indi-
cated 7
.
4 and the Data “STX SA 059 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-4 to Off, the 7-segment LED should be indi-
cated 7 4 and the Data “STX SA 060 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-5 to On, the 7-segment LED should be indi-
cated 7
.
5 and the Data “STX SA 061 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-5 to Off, the 7-segment LED should be indi-
cated 7 5 and the Data “STX SA 062 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-6 to On, the 7-segment LED should be indi-
cated 7
.
6 and the Data “STX SA 063 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-6 to Off, the 7-segment LED should be indi-
cated 7 6 and the Data “STX SA 064 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-7 to On, the 7-segment LED should be indi-
cated 7
.
7 and the Data “STX SA 065 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-7 to Off, the 7-segment LED should be indi-
cated 7 7 and the Data “STX SA 066 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-8 to On, the 7-segment LED should be indi-
cated 7
.
8 and the Data “STX SA 067 ETX” is transmitted
to the RS-232C line.
8
Set the SW7-8 to Off, the 7-segment LED should be indi-
cated 7 8 and the Data “STX SA 068 ETX” is transmitted
to the RS-232C line.
8
After completion the check of the SW7, all sections of the
SW7 are reset to the Off positions.
8
Set the SW8-1 to On, the 7-segment LED should be indi-
cated 8
.
1 and the Data “STX SA 069 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-1 to Off, the 7-segment LED should be indi-
cated 8 1 and the Data “STX SA 070 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-2 to On, the 7-segment LED should be indi-
cated 6
.
2 and the Data “STX SA 071 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-2 to Off, the 7-segment LED should be indi-
cated 6 2 and the Data “STX SA 072 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-3 to On, the 7-segment LED should be indi-
cated 6
.
3 and the Data “STX SA 073 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-3 to Off, the 7-segment LED should be indi-
cated 6 3 and the Data “STX SA 074 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-4 to On, the 7-segment LED should be indi-
cated 6
.
4 and the Data “STX SA 075 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-4 to Off, the 7-segment LED should be indi-
cated 6 4 and the Data “STX SA 076 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-5 to On, the 7-segment LED should be indi-
cated 6
.
5 and the Data “STX SA 077 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-5 to Off, the 7-segment LED should be indi-
cated 6 5 and the Data “STX SA 078 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-6 to On, the 7-segment LED should be indi-
cated 6
.
6 and the Data “STX SA 079 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-6 to Off, the 7-segment LED should be indi-
cated 6 6 and the Data “STX SA 080 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-7 to On, the 7-segment LED should be indi-
cated 6
.
7 and the Data “STX SA 081 ETX” is transmitted
to the RS-232C line.
8
Set the SW8-7 to Off, the 7-segment LED should be indi-
cated 6 7 and the Data “STX SA 082 ETX” is transmitted
to the RS-232C line.
Click on the first or last page to see other WJ-SX550 service manuals if exist.