JBL SUB 250P (serv.man2) EMC - CB Certificate ▷ View online
Page 34 of 57
Report No.: 11034065 001
IEC 60065 ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
RATED CURRENT
CONSUMPTION of the
apparatus
CONSUMPTION of the
apparatus
a
A
Nominal cross-
sectional area
sectional area
mm
2
up to and including 6
Over 6 up to and including
10
10
Over 10 up to and including
16
16
0,75
1
1,5
a
The RATED CURRENT CONSUMPTION
includes currents which can be drawn from
the socket-outlets providing MAINS power for
other apparatus.
the socket-outlets providing MAINS power for
other apparatus.
16.3
Replacement:
In item a), replace “IEC 60885-1” by “JIS C 3661-
1:1998”.
1:1998”.
N/A
Replacement:
In item b), replace “IEC 60227-2” by “JIS C 3662-
2 (corresponding to IEC 60227-2)”.
2 (corresponding to IEC 60227-2)”.
N/A
16.5
Addition:
Add “or CLASS 0I EQUIPMENT used a plug with
an external earth wire” after the words, CLASS I
EQUIPMENT.
an external earth wire” after the words, CLASS I
EQUIPMENT.
N/A
20.1
Replacement:
In Note 3, replace each IEC 60065 and IEC
60707 by “JIS C 6065” and “JIS C 0066:2001
(IEC 60707).
60707 by “JIS C 6065” and “JIS C 0066:2001
(IEC 60707).
N/A
Annex B
Replacement:
Replace normative by Informative.
N/A
Annex G
Replacement:
Replace IEC 60707 by JIS C 0066:2001
Replace IEC 60695-2-2 by JIS C 60695-2-
2:2000.
2:2000.
Replace IEC 60695-11-10 by JIS Z 2391:1999.
N/A
Annex N
Addition:
Add “- protective earthing lead wire, protective
earthing contact of appliance inlet or external
protective earthing terminal in case of Class 0I
apparatus.” after the second dash of N.1.3.
earthing contact of appliance inlet or external
protective earthing terminal in case of Class 0I
apparatus.” after the second dash of N.1.3.
N/A
Replacement:
Replace the first sentence and two dashes of
N.2.2, as follows:
N.2.2, as follows:
The continuity of the protective earthing
conecction between
conecction between
- the ACCESSIBLE conductive parts, including
TERMINALS regarded as ACCESSIBLE (see
N/A
Page 35 of 57
Report No.: 11034065 001
IEC 60065 ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
8.4), which should be connected to the
PROTECTIVE EARTHING TERMINAL, and
PROTECTIVE EARTHING TERMINAL, and
- the protective earthing contact of socket-outlets
respectively, if provided to deliver power to other
apparatus
apparatus
should be checked between
- the protective earthing contact of the MAINS
plug or appliance inlet, or the PROTECTIVE
EARTHING TERMINAL in case of a
PERMANENTLY CONNECTED APPARATUS,
for CLASS I apparatus, and
EARTHING TERMINAL in case of a
PERMANENTLY CONNECTED APPARATUS,
for CLASS I apparatus, and
- the protective earthing lead wire, the protective
earthing contact of appliance inlet, or external
protective earthing terminal, for CLASS 0I
apparatus.
earthing contact of appliance inlet, or external
protective earthing terminal, for CLASS 0I
apparatus.
Page 36 of 57
Report No.: 11034065 001
IEC 60065 ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60065
SWEDEN NATIONAL DIFFERENCES
Audio, video and similar electronic apparatus – Safety requirements
Differences according .................... :
SS-EN 60065, 3rd EDITION
Attachment Form No. ..................... :
Attachment Form Originator ......... :
TUV Rheinland Taiwan
Master Attachment Form ............... :
IECEE CB Bulletin on 2011-04-19
Clause
Requirement + Test
Result - Remark
Verdict
Annex B
Replace NOTE 1 by
In the CENELEC countries listed in IEC 62151,
special national conditions apply.
special national conditions apply.
Add the following:
All subclauses given below are subclauses of IEC
62151:2000 (ref. Corrigendum 1 and 2 to IEC
62151).
62151:2000 (ref. Corrigendum 1 and 2 to IEC
62151).
Subclause 4.1.1 (Corrigendum 2):
Add after the first paragraph:
NOTE - In Sweden, CLASS I equipment which is
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
The marking text shall be as follows:
"Apparaten skall anslutas till jordat uttag”
Subclause 5.3.1 (Corrigendum 1):
Add after the first test specifications paragraph:
NOTE 1 In Finland, Norway and Sweden, there
are additional requirements for the insulation.
are additional requirements for the insulation.
Renumber the existing note as note 2.
For additional requirements for the insulation in
Sweden in the NOTE 1 the following text is added
between the first and second paragraph (this text
is identical to the text in EN 60950-1:2001):
Sweden in the NOTE 1 the following text is added
between the first and second paragraph (this text
is identical to the text in EN 60950-1:2001):
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
forming part of a component, it shall at least
consist of either
- two layers of thin sheet material, each of which
N/A
Page 37 of 57
Report No.: 11034065 001
IEC 60065 ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
shall pass the electric strength test below, or
- one layer having a distance through insulation
of at least 0,4 mm, which shall pass the electric
of at least 0,4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES do
not exist, if the component passes the electric
strength test in the accordance with the
compliance clause below and in addition:
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES do
not exist, if the component passes the electric
strength test in the accordance with the
compliance clause below and in addition:
- passes the test and inspection criteria of 13.6
with an electric strength test of 10.3 using the test
voltage of 1,5 kV multiplied by 1,6, and
with an electric strength test of 10.3 using the test
voltage of 1,5 kV multiplied by 1,6, and
- is subject to routine testing for electric strength
during manufacturing, using a test voltage of 1,5
kV (for performance of the test see N.2.1).
during manufacturing, using a test voltage of 1,5
kV (for performance of the test see N.2.1).
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
capacitor complying with IEC 60384-14:1993,
subclass Y2.
A capacitor classified Y3 according to IEC 60384-
14:1993, may bridge this insulation under the
following conditions:
14:1993, may bridge this insulation under the
following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by
IEC 60384-14, which in addition to the Y3 testing,
is tested with an Impulse test of 2.5kV defined in
IEC 62151, subclause 6.2.1;
having a capacitor classified Y3 as defined by
IEC 60384-14, which in addition to the Y3 testing,
is tested with an Impulse test of 2.5kV defined in
IEC 62151, subclause 6.2.1;
- the additional testing shall be performed on all
the test specimens as described in IEC 60384-
14;
the test specimens as described in IEC 60384-
14;
- the Impulse test of 2.5kV is to be performed
before the Endurance Test in IEC 60384-14 in
the sequence of tests as described in IEC 60384-
14.
before the Endurance Test in IEC 60384-14 in
the sequence of tests as described in IEC 60384-
14.
Subclause 5.3.2 (Corrigendum 1):
Add after the fourth dash:
NOTE - In Sweden, exclusions are applicable for
equipment which is intended for connection to the
building installation wiring using screw terminals
or other reliable means, and for equipment which
is intended for connection to the building
installation wiring via an industrial plug and
equipment which is intended for connection to the
building installation wiring using screw terminals
or other reliable means, and for equipment which
is intended for connection to the building
installation wiring via an industrial plug and
socket -outlet or an appliance coupler, or both,
complying with IEC 60309 or with a comparable
national standard
complying with IEC 60309 or with a comparable
national standard
Click on the first or last page to see other SUB 250P (serv.man2) service manuals if exist.