JBL SPOT (serv.man3) EMC - CB Certificate ▷ View online
Page 43 of 62
Ref. No. : 06-1331-0461
IEC/EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN 60065F
TRF originator BEAB
15.1.3
Add the following title
Adapter output connectors
Replace the first paragraph with the following
Terminals and connectors used in output circuits of
supply apparatus, whose output voltage is not a
standard nominal mains voltage according to IEC
60038 (1), IEC 60320, IEC 60884, IEC 60906
(parts 1, 2, and 3), and CSA C22.2 No. 42.
supply apparatus, whose output voltage is not a
standard nominal mains voltage according to IEC
60038 (1), IEC 60320, IEC 60884, IEC 60906
(parts 1, 2, and 3), and CSA C22.2 No. 42.
N
15.2
Provisions for protective earthing
Replace the first paragraph with the following
Earthing connections shall comply with the test
requirements of CSA C22.2 No. 0.4.
requirements of CSA C22.2 No. 0.4.
N
15.3
Terminals for external flexible cords and for
permanent connection to the mains supply
permanent connection to the mains supply
—
15.3.1A
Add the following clause
Equipment intended for permanent connection to
the mains shall have provisions for connection to
the wiring system in accordance with the Canadian
Electrical Code, Part I.
the mains shall have provisions for connection to
the wiring system in accordance with the Canadian
Electrical Code, Part I.
The terminal parts and all other provisions for
permanent connection to fixed wiring shall comply
with CSA Standard CAN/CSA-C22.2 No. 0.
permanent connection to fixed wiring shall comply
with CSA Standard CAN/CSA-C22.2 No. 0.
Not such equipment.
N
15.4
Devices forming a part of the mains plug
—
15.4.2
Add the following paragraphs
Mains plugs of non-permanently installed
equipment shall comply with
equipment shall comply with
a) CSA C22.2 No. 21 for moulded-on type
attachment plugs; and
attachment plugs; and
b) CSA C22.2 No. 42 for disassembly type
attachment plugs (dimensional requirements are
also specified in IEC 60906-2).
attachment plugs (dimensional requirements are
also specified in IEC 60906-2).
Class II equipment provided with a general
purpose mains outlet, or lampholder, shall be
provided with a polarized-type plug.
purpose mains outlet, or lampholder, shall be
provided with a polarized-type plug.
If the plug is a polarized type, single pole switches
or over current protectors shall not be connected in
the identified conductor.
or over current protectors shall not be connected in
the identified conductor.
N
16
External flexible cords
—
Page 44 of 62
Ref. No. : 06-1331-0461
IEC/EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN 60065F
TRF originator BEAB
16.1
Replace this clause with the following
Flexible cord used for mains supply shall comply
with the requirements of CSA C22.2 No. 49. The
cord type shall be in accordance with Table 4 of
CSA C22.2 No. 1.
with the requirements of CSA C22.2 No. 49. The
cord type shall be in accordance with Table 4 of
CSA C22.2 No. 1.
The attachment plug shall be rated not less than
125% of the apparatus rated current.
125% of the apparatus rated current.
Cord sets shall comply with the requirements of
CSA C22.2 No. 21.
CSA C22.2 No. 21.
Non-detachable flexible cables and cords of Class
I apparatus shall be provided with a green/yellow
core connected to the protective earthing terminal
of the apparatus and, if a plug is provided , to the
protective earthing contact of the plug.
I apparatus shall be provided with a green/yellow
core connected to the protective earthing terminal
of the apparatus and, if a plug is provided , to the
protective earthing contact of the plug.
Compliance is checked by inspection.
Note: The colour for cores of flexible mains cords is contained in
IEC 60173 (4).
IEC 60173 (4).
No such cord.
N
17
Electrical connections and mechanical fixings
—
17.9A
Adhesive securement and conductive coatings
Add the following clause
No such part.
N
17.9A.1
Adhesive securement
The following parts, the displacement of which may
result in a fire or shock hazard, shall not be
secured solely by adhesive, unless the adhesive
system complies with the resistance to external
forces test of Clause 9.1.7, the bump test of
Clause 12.1.1, and the impact test of Clause
12.1.3, after conditioning in accordance with
Clause 17.9A.2:
result in a fire or shock hazard, shall not be
secured solely by adhesive, unless the adhesive
system complies with the resistance to external
forces test of Clause 9.1.7, the bump test of
Clause 12.1.1, and the impact test of Clause
12.1.3, after conditioning in accordance with
Clause 17.9A.2:
a) internal metal parts/conductive coatings;
b) barriers; and
c) required enclosure parts.
Note: Cathode ray tubes are excluded from this test.
N
17.9A.2
Adhesive and conductive coating securement
conditioning
conditioning
—
17.9A.2.1
General
Where required by Clause 17.9A.1, one sample of
the apparatus or enclosure section shall be
conditioned in accordance with the requirements of
Clause 17.9A.2.2. Equivalent ageing test data
supplied by the manufacturer will be considered in
lieu of ageing.
the apparatus or enclosure section shall be
conditioned in accordance with the requirements of
Clause 17.9A.2.2. Equivalent ageing test data
supplied by the manufacturer will be considered in
lieu of ageing.
N
Page 45 of 62
Ref. No. : 06-1331-0461
IEC/EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN 60065F
TRF originator BEAB
17.9A.2.2
Ageing
Day 1: Place in oven at 100
±
1°C for 1 week, or 82
±
1°C for 8 weeks at the manufacturer’s option.
Day 8 or Day 57:
1. Remove from oven and leave at room
temperature for 1h.
2. Place in freezer at –35°C for 2h.
3. Remove from freezer and allow to reach room
temperature overnight.
Day 9 or Day 58:
1. Place in a compartment at 96% relative
humidity for 3h.
2. Remove and leave at room temperature and
humidity for 1h.
3. Place in oven at a temperature selected in the
first cycle for 3h.
4. Remove and allow to come to room
temperature overnight.
Day 10 or Day 59:
1. Place in Freezer at –35°C for 2h.
2. Remove and leave at room temperature for
1h.
3. Place in humidity chamber at 96% relative
humidity for 3h.
4. Remove and allow to come to room
temperature overnight.
Day 11 or Day 60:
1. Place in oven at a temperature selected in the
first cycle for 3h.
2. Remove for 1h.
3. Place in Freezer at –35°C for 2h.
4. Remove and allow to come to room
temperature overnight.
Day 12 or Day 61:
1. Place in humidity chamber at 96% relative
humidity for 3h.
2. Remove and perform mechanical tests as
required by Clause 17.10.1 or 17.10.2 as
applicable.
applicable.
N
Page 46 of 62
Ref. No. : 06-1331-0461
IEC/EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN 60065F
TRF originator BEAB
18
Mechanical strength of picture tubes and
protection against the effects of implosion
protection against the effects of implosion
—
18.1A
Add the following clause
A picture tube with a maximum face dimension
exceeding 75mm either shall be intrinsically
protected with respect to effects of implosion and
to mechanical impact in accordance with
CAN/CSA - C22.2 No. 228 or CAN/CSA – E61965,
or the enclosure of the apparatus shall provide
adequate protection against the effects of an
implosion of the tube (see Clause 12)
exceeding 75mm either shall be intrinsically
protected with respect to effects of implosion and
to mechanical impact in accordance with
CAN/CSA - C22.2 No. 228 or CAN/CSA – E61965,
or the enclosure of the apparatus shall provide
adequate protection against the effects of an
implosion of the tube (see Clause 12)
No such tube.
N
19
Stability and mechanical hazards
Add the following after the second paragraph
The test of Clause 19.3 is only required for
a)
apparatus with a mass of 25kg or more
b)
apparatus, excluding loudspeaker
systems, with a height of 1m or more, or
c)
apparatus, including loudspeaker
systems, in combination with a supplied or
recommended cart of stand with a total height
of 1m or more.
recommended cart of stand with a total height
of 1m or more.
Add the following paragraph
Apparatus not tested because it is intended to be
fastened in place shall be provided with the
following warning:
fastened in place shall be provided with the
following warning:
“WARNING: This apparatus must be securely
attached to the floor/wall per installation instruction.
Tipping, shaking or rocking the machine may
cause injury/death.”
attached to the floor/wall per installation instruction.
Tipping, shaking or rocking the machine may
cause injury/death.”
N
20.2
Fire enclosure
—
20.2.1A
Add the following clause
Enclosures of apparatus containing high voltage or
projection lamps shall have a minimum
flammability rating of category FV1 according to
IEC 60707 at the minimum thickness used.
projection lamps shall have a minimum
flammability rating of category FV1 according to
IEC 60707 at the minimum thickness used.
No such parts
N
Annex B
(normative)
(normative)
Apparatus to be connected to the
telecommunication networks
telecommunication networks
Replace this annex with the following
Apparatus intended for direct connection to a
telecommunication network shall comply with
telecommunication network shall comply with
a) Clasue 19 of CSA C22.2 No.1; or
b) CAN/CSA – C22.2 No. 60950.
No TNV.
N
Click on the first or last page to see other SPOT (serv.man3) service manuals if exist.