JBL SPOT (serv.man3) EMC - CB Certificate ▷ View online
Page 31 of 62
Ref. No. : 06-1331-0461
IEC/EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN 60065F
TRF originator BEAB
NATIONAL DIFFERENCES OF AUSTRALIA : IEC 60065, 7th Edition (CB Bulletin No. 110A, June 2006)
ZZ.1 Introduction
This Annex sets out variations between this Standard and IEC 60065:2001.
These variations indicate national variations for purposes of the IECEE CB
Scheme and will be published in the IECEE CB Bulletin. These variations are
indicated within the body of the Standard by shading and strikethrough.
These variations indicate national variations for purposes of the IECEE CB
Scheme and will be published in the IECEE CB Bulletin. These variations are
indicated within the body of the Standard by shading and strikethrough.
ZZ.2
Variations
The variations are as follows:
7.1.5
In Table 3 under item c) add an h) in both columns
against 'thermoplastic materials' and add the
following new footnote:
against 'thermoplastic materials' and add the
following new footnote:
h As an alternative to the method described in
footnote f) the following variation may be used
where there is any doubt about the suitability of
the material:
footnote f) the following variation may be used
where there is any doubt about the suitability of
the material:
The ball-pressure test described in AS/NZS
60695.10.2 may be carried out.
60695.10.2 may be carried out.
To assess compliance under normal operating
conditions, the test shall be made in a heating
cabinet at a temperature of 40°C ± 2°C plus the
maximum temperature rise determined under
normal operating conditions but, it shall be at
least;
conditions, the test shall be made in a heating
cabinet at a temperature of 40°C ± 2°C plus the
maximum temperature rise determined under
normal operating conditions but, it shall be at
least;
- for external parts 75°C ± 2°C
- for material supporting parts conductively
connected to the mains 125°C ± 2°C.
connected to the mains 125°C ± 2°C.
N
7.2
After the second paragraph, add the following:
The alternative method described in footnote h) of
Table 3 may be used.
Table 3 may be used.
N
15.1.1
After the second paragraph, add the following:
Plugs for the connection of apparatus to mains-
powered socket-outlets shall comply with AS/NZS
3112 or AS/NZS 3123. Apparatus with a plug
portion, suitable for insertion into a 10 A 3-pin flat-
pin socket-outlet complying with AS/NZS 3112,
shall comply with the requirements of AS/NZS
3112 for equipment with integral pins for insertion
into socket-outlets.
powered socket-outlets shall comply with AS/NZS
3112 or AS/NZS 3123. Apparatus with a plug
portion, suitable for insertion into a 10 A 3-pin flat-
pin socket-outlet complying with AS/NZS 3112,
shall comply with the requirements of AS/NZS
3112 for equipment with integral pins for insertion
into socket-outlets.
18 Vdc powered equipment
N
15.3.5
In Table 15, in the second and third rows of the
first column replace ‘6’ with ‘7.5’.
first column replace ‘6’ with ‘7.5’.
N
Page 32 of 62
Ref. No. : 06-1331-0461
IEC/EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN 60065F
TRF originator BEAB
16.2
In Table 18, in the second and third rows of the
first column replace ‘6’ with ‘7.5’.
first column replace ‘6’ with ‘7.5’.
N
16.3
In item (b), add the following:
A flexible cord complying with AS/NZS 3191 need
not undergo this test.
not undergo this test.
N
20
Add the following after NOTE 2:
For alternative test refer to Clause 20.201.
N
20.1.4
In Table 21, in the third and fourth columns
change both ‘HB75’ and ‘No requirement’ to ‘V-1’.
change both ‘HB75’ and ‘No requirement’ to ‘V-1’.
No potential ignition sources
N
20.2.3
After this Clause, add the following variation:
20.201
Resistance to fire-Alternative tests
N
20.201.1 General
Parts of non-metallic material shall be resistant to
ignition and the spread of fire.
ignition and the spread of fire.
This requirement does not apply to decorative
trims, knobs and other parts unlikely to be ignited
or to propagate flames originating from inside the
apparatus, or the following:
trims, knobs and other parts unlikely to be ignited
or to propagate flames originating from inside the
apparatus, or the following:
N
(a) Components that are contained in an
enclosure having a flammability category of V-O
according to AS/NZS 60695.11.10 and having
openings only for the connecting wires filling the
openings completely, and for ventilation not
exceeding 1 mm in width regardless of length.
enclosure having a flammability category of V-O
according to AS/NZS 60695.11.10 and having
openings only for the connecting wires filling the
openings completely, and for ventilation not
exceeding 1 mm in width regardless of length.
N
(b) The following parts which would contribute
negligible fuel to a fire:
negligible fuel to a fire:
- small mechanical parts, the mass of which does
not exceed 4 g, such as mounting parts, gears,
cams, belts and bearings;
not exceed 4 g, such as mounting parts, gears,
cams, belts and bearings;
- small electrical components, such as capacitors
with a volume not exceeding 1 750 mm
with a volume not exceeding 1 750 mm
3
,
integrated circuits, transistors and optocoupler
packages, if these components are mounted on
material of flammability category V-1 or better
according to AS/NZS 60695.11.10.
packages, if these components are mounted on
material of flammability category V-1 or better
according to AS/NZS 60695.11.10.
NOTE - In considering how to minimize
propagation of fire and what 'small parts' are,
account should be taken of the cumulative effect
of small parts adjacent to each other for the
possible effect of propagating fire from one part
to another.
propagation of fire and what 'small parts' are,
account should be taken of the cumulative effect
of small parts adjacent to each other for the
possible effect of propagating fire from one part
to another.
N
Page 33 of 62
Ref. No. : 06-1331-0461
IEC/EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN 60065F
TRF originator BEAB
Compliance shall be checked by the tests of
20.201.2.1, 20.201.2.2. and 20.201.2.3
20.201.2.1, 20.201.2.2. and 20.201.2.3
N
For the base material of printed boards,
compliance shall be checked by the test of
20.201.2.4.
compliance shall be checked by the test of
20.201.2.4.
N
The tests shall be carried out on parts of non-
metallic material which have been removed from
the apparatus. When the glow-wire test is carried
out, they are placed in the same orientation as
they would be in normal use.
metallic material which have been removed from
the apparatus. When the glow-wire test is carried
out, they are placed in the same orientation as
they would be in normal use.
These tests are not carried out on internal wiring.
N
20.201.2 Tests
N
20.201.2.1 Testing of non-metallic parts
N
Parts of non-metallic material shall be subject to
the glow-wire test of AS/NZS 60695.2.11 which
shall be carried out at 550
the glow-wire test of AS/NZS 60695.2.11 which
shall be carried out at 550
o
C.
N
Parts for which the glow-wire test cannot be
carried out, such as those made of soft or foamy
material, shall meet the requirements specified in
ISO 9772 for category FH-3 material. The glow-
wire test shall not be carried out on parts of
material classified at least FH-3 according to ISO
9772 provided that the sample tested was not
thicker than the relevant part.
carried out, such as those made of soft or foamy
material, shall meet the requirements specified in
ISO 9772 for category FH-3 material. The glow-
wire test shall not be carried out on parts of
material classified at least FH-3 according to ISO
9772 provided that the sample tested was not
thicker than the relevant part.
N
20.201.2.2 Testing of insulated parts
Part of insulating material supporting potential
ignition sources shall be subject to the glow-wire
test of AS/NZS 64695.2.11 which shall be carried
out at 750
ignition sources shall be subject to the glow-wire
test of AS/NZS 64695.2.11 which shall be carried
out at 750
o
C.
N
The test shall be also carried out on other parts of
insulating material which are within a distance of
3 mm of the connection
insulating material which are within a distance of
3 mm of the connection
NOTE - Contacts in components such as switch
contacts are considered to be connections.
contacts are considered to be connections.
N
For parts which withstand the glow-wire test but
produce a flame, other parts above the
connection within the envelope of a vertical
cylinder having a diameter of 20 mm and a height
of 50 mm shall be subjected to the needle-flame
test. However, parts shielded by a barrier which
meets the needle-flame test need not be tested.
produce a flame, other parts above the
connection within the envelope of a vertical
cylinder having a diameter of 20 mm and a height
of 50 mm shall be subjected to the needle-flame
test. However, parts shielded by a barrier which
meets the needle-flame test need not be tested.
N
The needle-flame test shall be made in
accordance with AS/NZS 4695.2.2 with the
following modifications:
accordance with AS/NZS 4695.2.2 with the
following modifications:
N
Page 34 of 62
Ref. No. : 06-1331-0461
IEC/EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No: IECEN 60065F
TRF originator BEAB
5 Severities
Replace with:
The duration of application of the test flame shall
be 30 s ± 1 s.
be 30 s ± 1 s.
Noted
8 Test
procedure
8.2
Replace the first sentence with:
The specimen shall be arranged so that the flame
can be applied to a vertical or horizontal edge as
shown in the examples of figure 1.
can be applied to a vertical or horizontal edge as
shown in the examples of figure 1.
Noted
8.4
The first paragraph does not apply.
Noted
.
Addition:
If possible, the flame shall be applied at least 10
mm from a corner.
mm from a corner.
Noted
8.5
Replace with:
The test shall be made on one specimen. If the
specimen does not withstand the test, the test
may be repeated on two further specimens, both
of which shall then withstand the test.
specimen does not withstand the test, the test
may be repeated on two further specimens, both
of which shall then withstand the test.
Noted
10
Evaluation of test results
Replace with:
The duration of burning (tb) shall not exceed 30
s. However, for printed circuit boards, it shall not
exceed 15 s.
s. However, for printed circuit boards, it shall not
exceed 15 s.
Noted
The needle-flame test shall not be carried out on
parts of material classified as V-0 or V-1
according to AS/NZS 60695.11.10 provided that
the sample tested was not thicker than the
relevant part.
parts of material classified as V-0 or V-1
according to AS/NZS 60695.11.10 provided that
the sample tested was not thicker than the
relevant part.
N
20.201.2.3 Testing by needle-flame test
If parts, other than enclosures, do not withstand
the glow wire tests of 20.201.2.2, by failure to
extinguish within 30 s after the removal of the
glow-wire tip, the needle-flame test detailed in
20.201.2.2 shall be made on all parts of non-
metallic material which are within a distance of 50
mm or which are likely to be impinged upon by
flame during the tests of 20.201.2.2. Parts
shielded by a separate barrier which meets the
needle-flame test shall not be tested.
the glow wire tests of 20.201.2.2, by failure to
extinguish within 30 s after the removal of the
glow-wire tip, the needle-flame test detailed in
20.201.2.2 shall be made on all parts of non-
metallic material which are within a distance of 50
mm or which are likely to be impinged upon by
flame during the tests of 20.201.2.2. Parts
shielded by a separate barrier which meets the
needle-flame test shall not be tested.
N
Click on the first or last page to see other SPOT (serv.man3) service manuals if exist.