JBL ON STAGE III IIIP (serv.man2) EMC - CB Certificate ▷ View online
<12014238 001 >
Page 16 of 77
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Number of conductors, diameter (mm) of cable
and conduits ........................................................:
and conduits ........................................................:
3.2.4
Appliance inlets
Direct plug-in equipment.
N/A
3.2.5
Power supply cords
No power cord.
N/A
3.2.5.1
AC power supply cords
N/A
Type ......................................................................:
Rated current (A), cross-sectional area (mm2),
AWG .....................................................................:
AWG .....................................................................:
3.2.5.2
DC power supply cords
AC Source.
N/A
3.2.6
Cord anchorages and strain relief
No power cord.
N/A
Mass of equipment (kg), pull (N) ........................:
Longitudinal displacement (mm) ..........................:
3.2.7
Protection against mechanical damage
No parts under this unit likely to
damage the power supply cord.
No sharp edges.
damage the power supply cord.
No sharp edges.
P
3.2.8
Cord guards
No cord guard provided.
N/A
D (mm); test mass (g) ..........................................:
Radius of curvature of cord (mm).........................:
3.2.9
Supply wiring space
Not permanent connection or
non-detachable power cord
type.
non-detachable power cord
type.
N/A
3.3
Wiring terminals for connection of external conductors
N/A
3.3.1
Wiring terminals
Direct plug-in equipment.
N/A
3.3.2
Connection of non-detachable power supply
cords
cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
Rated current (A), cord/cable type, cross-sectional
area (mm2) ...........................................................:
area (mm2) ...........................................................:
3.3.5
Wiring terminal sizes
N/A
Rated current (A), type and nominal thread
diameter (mm) .....................................................:
diameter (mm) .....................................................:
3.3.6
Wiring terminals design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection from the mains supply
P
3.4.1
General requirement
Disconnect device provided.
P
<12014238 001 >
Page 17 of 77
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
3.4.2
Disconnect devices
Plug of this direct plug-in
equipment was used as
disconnected device.
equipment was used as
disconnected device.
P
3.4.3
Permanently connected equipment
Not permanently connected
equipment.
equipment.
N/A
3.4.4
Parts which remain energized
There is no parts remained with
hazardous voltage or energy in
the equipment when SPS is
separated from AC mains.
hazardous voltage or energy in
the equipment when SPS is
separated from AC mains.
P
3.4.5
Switches in flexible cords
No flexible cords.
N/A
3.4.6
Single-phase equipment and d.c. equipment
The mains plug disconnects
both poles simultaneously.
both poles simultaneously.
P
3.4.7
Three-phase equipment
Single phase equipment.
N/A
3.4.8
Switches as disconnect devices
See sub-clause 3.4.2.
N/A
3.4.9
Plugs as disconnect devices
See sub-clause 3.4.2.
N/A
3.4.10
Interconnected equipment
No interconnections using
hazardous voltages.
hazardous voltages.
N/A
3.4.11
Multiple power sources
Only one supply connection
provided.
provided.
N/A
3.5
Interconnection of equipment
P
3.5.1
General requirements
This power supply is not
considered for connection to
TNV.
considered for connection to
TNV.
P
3.5.2
Types of interconnection circuits ..........................: Interconnection circuits of
SELV through the connector.
No ELV interconnection
circuits.
No ELV interconnection
circuits.
P
3.5.3
ELV circuits as interconnection circuits
No ELV interconnection
N/A
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
N/A
Angle of 10°
Direct plug-in equipment.
N/A
Test: force (N).......................................................:
N/A
4.2
Mechanical strength
P
4.2.1
General
See below. After tests, unit
comply with 2.1.1, 2.6.1, 2.10
and 4.4.1.
comply with 2.1.1, 2.6.1, 2.10
and 4.4.1.
P
4.2.2
Steady force test, 10 N
10N applied to components
other than parts serving as an
enclosure.
other than parts serving as an
enclosure.
P
<12014238 001 >
Page 18 of 77
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
4.2.3
Steady force test, 30 N
No internal enclosure.
N/A
4.2.4
Steady force test, 250 N
250N applied to outer
enclosure. No energy or other
hazards.
enclosure. No energy or other
hazards.
P
4.2.5
Impact test
Direct plug-in equipment.
N/A
Fall test
N/A
Swing test
N/A
4.2.6
Drop test
No hazard as result from drop
test.
test.
P
4.2.7
Stress relief test
After 7 hours at temperature of
75°C and cooling down to room
temperature, no shrinkage,
distortion or loosening any
enclosure part was noticeable
on the adapter.
75°C and cooling down to room
temperature, no shrinkage,
distortion or loosening any
enclosure part was noticeable
on the adapter.
Test was performed for all
sources of enclosure material.
sources of enclosure material.
P
4.2.8
Cathode ray tubes
No CRT provided.
N/A
Picture tube separately certified ...........................:
N/A
4.2.9
High pressure lamps
No High pressure lamps
provided.
provided.
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) .....: Direct plug-in equipment.
N/A
4.3
Design and construction
P
4.3.1
Edges and corners
All edges and corners are
rounded and /or smoothed.
rounded and /or smoothed.
P
4.3.2
Handles and manual controls; force (N) ...............: No handles or controls provided.
N/A
4.3.3
Adjustable controls
No controls provided.
N/A
4.3.4
Securing of parts
No connection likely to be
exposed to mechanical stress is
provided in unit.
exposed to mechanical stress is
provided in unit.
P
4.3.5
Connection of plugs and sockets
No mismating of connectors,
plugs or sockets possible.
plugs or sockets possible.
P
4.3.6
Direct plug-in equipment
The prevention of imposing to
undue strain on the socket-
outlet was done by construction
of the plug of adaptor.
undue strain on the socket-
outlet was done by construction
of the plug of adaptor.
For British plug: 0.07Nm;
For Australian plug: 0.08Nm;
For Japan plug: 0.07Nm.
P
<12014238 001 >
Page 19 of 77
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Dimensions (mm) of mains plug for direct plug-in : (See attached partial test
reports)
P
Torque and pull test of mains plug for direct
plug-in; torque (Nm); pull (N) ................................:
plug-in; torque (Nm); pull (N) ................................:
See above.
P
4.3.7
Heating elements in earthed equipment
No heating elements provided.
N/A
4.3.8
Batteries
No batteries provided.
N/A
4.3.9
Oil and grease
No heating elements provided.
N/A
4.3.10
Dust, powders, liquids and gases
Equipment in intended use not
considered to be exposed to
these.
considered to be exposed to
these.
N/A
4.3.11
Containers for liquids or gases
No container for liquid or gas.
N/A
4.3.12
Flammable liquids.................................................: No such flammable liquid.
N/A
Quantity of liquid (l) ...............................................:
N/A
Flash point (°C).....................................................:
N/A
4.3.13
Radiation; type of radiation ..................................: No optical radiation present.
N/A
4.3.13.1
General
N/A
4.3.13.2
Ionizing radiation
N/A
Measured radiation (pA/kg) .................................:
Measured high-voltage (kV) ................................:
Measured focus voltage (kV) ...............................:
CRT markings .....................................................:
4.3.13.3
Effect of ultraviolet (UV) radiation on materials
N/A
Part, property, retention after test, flammability
classification ........................................................:
classification ........................................................:
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation ......:
N/A
4.3.13.5
Laser (including LEDs)
No optical radiation present.
N/A
Laser class ...........................................................:
4.3.13.6
Other types ..........................................................:
N/A
4.4
Protection against hazardous moving parts
N/A
4.4.1
General
No moving parts.
N/A
4.4.2
Protection in operator access areas
N/A
4.4.3
Protection in restricted access locations
N/A
4.4.4
Protection in service access areas
N/A
4.5
Thermal requirements
P
4.5.1
Maximum temperatures
See appended table 4.5.1.
P
Click on the first or last page to see other ON STAGE III IIIP (serv.man2) service manuals if exist.