JBL ON BEAT XTREME (serv.man8) EMC - CB Certificate ▷ View online
Page 7 of 11
Report No.: 171153
ATTACHMENT 6
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
14.12
Surge suppression varistors
Add the following paragraph:
As an alternative, a varistor complying with CSA
C22.2 No. 1 shall be acceptable.
As an alternative, a varistor complying with CSA
C22.2 No. 1 shall be acceptable.
No surge varistor
N/A
14.12A
Gas discharge tubes
Add New Clause 14.12A:
Gas discharge tubes complying with the following
tests may be connected to bridge BASIC or
REINFORCED INSULATION.
Ten samples of gas discharge tubes isolating the
ac supply from exposed parts shall be subjected to
the varistor pulse tests of Clause 14.12. Following
the pulses, the device shall be allowed to return to
room temperature. The dielectric breakdown
voltage of the gas tube shall not decrease by more
than 50% and the gas discharge tube shall comply
with the electric strength test of Clause 10.3, with
the test voltage reduced to twice the mains
voltage.
Add New Clause 14.12A:
Gas discharge tubes complying with the following
tests may be connected to bridge BASIC or
REINFORCED INSULATION.
Ten samples of gas discharge tubes isolating the
ac supply from exposed parts shall be subjected to
the varistor pulse tests of Clause 14.12. Following
the pulses, the device shall be allowed to return to
room temperature. The dielectric breakdown
voltage of the gas tube shall not decrease by more
than 50% and the gas discharge tube shall comply
with the electric strength test of Clause 10.3, with
the test voltage reduced to twice the mains
voltage.
No gas tube
N/A
15.1
15.1.1
Plugs and sockets
(Convenience Receptacle Type)
Add the Following Clause:
Add the Following Clause:
A receptacle provided for general purpose mains
output shall comply with the requirements of CSA
Standard C22.2 No 42 (dimensional requirements
are also specified in IEC 60906-2). The attachment
plug cap shall be polarized type when the
apparatus is provided with a manually operated,
MAINS connected single pole switch for apparatus
on-off operation, a socket screwshell lampholder,
or a 15 or 20 A socket outlet.
output shall comply with the requirements of CSA
Standard C22.2 No 42 (dimensional requirements
are also specified in IEC 60906-2). The attachment
plug cap shall be polarized type when the
apparatus is provided with a manually operated,
MAINS connected single pole switch for apparatus
on-off operation, a socket screwshell lampholder,
or a 15 or 20 A socket outlet.
No socket outlet
N/A
15.1.2
(Audio Terminals)
Add the following paragraph:
Banana plugs shall be acceptable.
Add the following paragraph:
Banana plugs shall be acceptable.
No banana plugs
N/A
15.1.3
Adapter output connectors
Replace the first paragraph with the following:
Terminals and connectors used in output circuits of
supply apparatus, whose output is not a standard
nominal mains voltage according to IEC 60038,
Table 1, shall not be compatible with those
specified for household and similar general
purposes, for example those described in IEC
60083[1], IEC 60320, IEC 60884, IEC 60906 (parts
1, 2, and 3), and CSA C22.2 No 42.
Replace the first paragraph with the following:
Terminals and connectors used in output circuits of
supply apparatus, whose output is not a standard
nominal mains voltage according to IEC 60038,
Table 1, shall not be compatible with those
specified for household and similar general
purposes, for example those described in IEC
60083[1], IEC 60320, IEC 60884, IEC 60906 (parts
1, 2, and 3), and CSA C22.2 No 42.
No mains output
P
Page 8 of 11
Report No.: 171153
ATTACHMENT 6
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
15.2
Provisions for protective earthing - Bond
Impedance
Replace the third paragraph with the following:
Earthing connections shall comply with the test
requirements of CSA C22.2 No 0.4.
Impedance
Replace the third paragraph with the following:
Earthing connections shall comply with the test
requirements of CSA C22.2 No 0.4.
Class ll apparatus
N/A
15.3
15.3.1A
Terminals for external flexible cords and
permanent connections to the mains supply
permanent connections to the mains supply
(Permanent Wiring)
Add the following clauses:
Equipment intended for permanent connection to
the mains shall have provisions for connection to
the wiring system in accordance with the Canadian
Electrical Code, Part I.
Add the following clauses:
Equipment intended for permanent connection to
the mains shall have provisions for connection to
the wiring system in accordance with the Canadian
Electrical Code, Part I.
Appliance inlet applied
N/A
The terminal parts and all other provisions for
permanent connection to fixed wiring shall comply
with CSA Standard CAN/CSA-C22.2 No 0.
permanent connection to fixed wiring shall comply
with CSA Standard CAN/CSA-C22.2 No 0.
Apparatus is not for
permanent connection.
permanent connection.
N/A
15.4.2
(Mains Plugs – Type)
Add the following paragraphs:
Mains plugs of non-permanently installed
equipment shall comply with:
Add the following paragraphs:
Mains plugs of non-permanently installed
equipment shall comply with:
a)
CSA C22.2 No 21 for moulded-on type
attachment plugs; and
b)
CSA C22.2 No 42 for disassembly type
attachment plugs (dimensional requirements are
also specified in IEC 60906-2).
also specified in IEC 60906-2).
CSA approved attachment plug
P
Class II equipment provided with a general
purpose mains outlet, or lampholder, shall be
provided with a polarized-type plug.
purpose mains outlet, or lampholder, shall be
provided with a polarized-type plug.
N/A
If the plug is a polarized type, single pole switches
or over current protectors shall not be
connected in the identified conductor.
or over current protectors shall not be
connected in the identified conductor.
P
Page 9 of 11
Report No.: 171153
ATTACHMENT 6
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
16
16.1
External flexible cords
Replace this clause with the following:
Flexible cord used for mains supply shall comply
with the requirements of CSA C22.2 No 49. The
cord type shall be in accordance with Table 4 of
CSA C22.2 No 1.
The attachment plug shall be rated not less than
125% of the apparatus rated current.
Cord sets shall comply with the requirements of
CSA C22.2 No 21.
Non-detachable flexible cables and cords of Class
I apparatus shall be provided with a green/yellow
core connected to the protective earthing terminal
of the apparatus and, if a plug is provided, to the
protective earthing contact of the plug.
Compliance is checked by inspection.
Note: The colour of cores of flexible mains cords is
contained in IEC 60173[4].
Flexible cord used for mains supply shall comply
with the requirements of CSA C22.2 No 49. The
cord type shall be in accordance with Table 4 of
CSA C22.2 No 1.
The attachment plug shall be rated not less than
125% of the apparatus rated current.
Cord sets shall comply with the requirements of
CSA C22.2 No 21.
Non-detachable flexible cables and cords of Class
I apparatus shall be provided with a green/yellow
core connected to the protective earthing terminal
of the apparatus and, if a plug is provided, to the
protective earthing contact of the plug.
Compliance is checked by inspection.
Note: The colour of cores of flexible mains cords is
contained in IEC 60173[4].
Complying with CSA C22.2.
See appended table, list of
critical components.
critical components.
P
17.9A
17.9A.1
Adhesive securement and conductive coatings
Add the following clause:
Adhesive securement
The following parts, the displacement of which may
result in a fire or shock hazard, shall not be
secured solely by adhesive, unless the adhesive
system complies with the resistance to external
forces test of Clause 9.1.7, the bump test of
Clause 12.1.1, and the impact test of Clause
12.1.3, after conditioning in accordance with
Clause 17.9A.2:
a) internal metal parts/conductive coatings;
b) barriers; and
c) required enclosure parts.
Note: Cathode ray tubes are excluded from this
test.
Adhesive securement
The following parts, the displacement of which may
result in a fire or shock hazard, shall not be
secured solely by adhesive, unless the adhesive
system complies with the resistance to external
forces test of Clause 9.1.7, the bump test of
Clause 12.1.1, and the impact test of Clause
12.1.3, after conditioning in accordance with
Clause 17.9A.2:
a) internal metal parts/conductive coatings;
b) barriers; and
c) required enclosure parts.
Note: Cathode ray tubes are excluded from this
test.
N/A
17.9A.2
17.9A.2.1
Adhesive and conductive coating securement
conditioning
conditioning
General:
Where required by Clause 17.9A.1, one sample of
the apparatus or enclosure section shall be
conditioned in accordance with the requirements of
Clause 17.9A.2.2. Equivalent ageing test data
supplied by the manufacturer will be considered in
lieu of ageing.
Where required by Clause 17.9A.1, one sample of
the apparatus or enclosure section shall be
conditioned in accordance with the requirements of
Clause 17.9A.2.2. Equivalent ageing test data
supplied by the manufacturer will be considered in
lieu of ageing.
N/A
Page 10 of 11
Report No.: 171153
ATTACHMENT 6
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
17.9A.2.2
Ageing
Day 1: Place in oven at 100 ± 1ºC for 1 week, or 82
± 1ºC for 8 weeks at the manufacturer’s option.
Day 8 or Day 57:
1. Remove from oven and leave at room temperature
for 1 h.
2. Place in freezer at –35ºC for 2 h.
3. Remove from freezer and allow to reach room
temperature overnight.
Day 9 or Day 58:
1. Place in a compartment at 96% relative humidity
for 3 h.
2. Remove and leave at room temperature and
humidity for 1 h.
3. Place in over at a temperature selected in the first
cycle for 3 h.
4. Remove and allow to come to room temperature
overnight.
Day 10 or Day 59:
1. Place in freezer at –35ºC for 2 h.
2. Remove and leave at room temperature for 1 h.,
3. Place in humidity chamber at 96% relative
humidity for 3 h.
4. Remove and allow to come to room temperature
overnight.
Day 11 or Day 60:
1. Place in oven at the temperature selected in the
first cycle for 3 h.
2. Remove for 1 h.
3. Place in freezer at –35ºC for 2 h.
4. Remove and allow to come to room temperature
overnight.
Day 12 or Day 61:
1. Place in humidity chamber at 96% relative
humidity for 3 h.
2. Remove and perform mechanical tests as required
by Clause 17.9A.1 as applicable.
Day 1: Place in oven at 100 ± 1ºC for 1 week, or 82
± 1ºC for 8 weeks at the manufacturer’s option.
Day 8 or Day 57:
1. Remove from oven and leave at room temperature
for 1 h.
2. Place in freezer at –35ºC for 2 h.
3. Remove from freezer and allow to reach room
temperature overnight.
Day 9 or Day 58:
1. Place in a compartment at 96% relative humidity
for 3 h.
2. Remove and leave at room temperature and
humidity for 1 h.
3. Place in over at a temperature selected in the first
cycle for 3 h.
4. Remove and allow to come to room temperature
overnight.
Day 10 or Day 59:
1. Place in freezer at –35ºC for 2 h.
2. Remove and leave at room temperature for 1 h.,
3. Place in humidity chamber at 96% relative
humidity for 3 h.
4. Remove and allow to come to room temperature
overnight.
Day 11 or Day 60:
1. Place in oven at the temperature selected in the
first cycle for 3 h.
2. Remove for 1 h.
3. Place in freezer at –35ºC for 2 h.
4. Remove and allow to come to room temperature
overnight.
Day 12 or Day 61:
1. Place in humidity chamber at 96% relative
humidity for 3 h.
2. Remove and perform mechanical tests as required
by Clause 17.9A.1 as applicable.
N/A
Click on the first or last page to see other ON BEAT XTREME (serv.man8) service manuals if exist.