JBL ON BEAT XTREME (serv.man8) EMC - CB Certificate ▷ View online
Page 7 of 16
Report No.: 171153
ATTACHMENT 5
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
14.5.1.3 Delete
N/A
14.5.2.1
Modification: Fuse links shall comply with
UL 248-14
UL 248-14
Fuses, IEC 60127.
P
14.5.2.2
Delete reference to IEC 60127 and breaking
capacity marking requirements.
capacity marking requirements.
Marked
N/A
14.5.3
Add: As an option, a PTC thermistor may comply
with UL 1434.
Delete the 3rd and 4th paragraphs.
with UL 1434.
Delete the 3rd and 4th paragraphs.
No PTC thermistor
N/A
14.5.3A
Add: Protective devices connected to the mains
shall have adequate breaking capacity and comply
with UL 873, UL 1416, UL 1417 or UL 2111 as
applicable.
shall have adequate breaking capacity and comply
with UL 873, UL 1416, UL 1417 or UL 2111 as
applicable.
N/A
14.5.4
Reference to fuse-links is deleted.
N/A
14.6.1
Add: “Switches and relays shall comply with UL 10
54, UL 61058-1 or UL 508 as applicable. Mains
switch or relay shall be rated for the total current
through the switch or relay contacts.”
Replace remaining text with: “A rating of a mains
switch or relay, provided on a audio apparatus
intended for commercial use, is to be equal to or
greater than the maximum steady state current it
controls under normal operating conditions except
the audio output is adjusted to 1/3 maximum
undistorted output or at 1/3 of the manufacturer’s
rated output power, whichever is greater.”
14.6.2, 14.6.3 and 14.6.4 are deleted.
54, UL 61058-1 or UL 508 as applicable. Mains
switch or relay shall be rated for the total current
through the switch or relay contacts.”
Replace remaining text with: “A rating of a mains
switch or relay, provided on a audio apparatus
intended for commercial use, is to be equal to or
greater than the maximum steady state current it
controls under normal operating conditions except
the audio output is adjusted to 1/3 maximum
undistorted output or at 1/3 of the manufacturer’s
rated output power, whichever is greater.”
14.6.2, 14.6.3 and 14.6.4 are deleted.
No switches
N/A
14.6.5
Modification: A switch or relay that controls a mains
socket-outlet shall have a rating equal to the
rated current consumption of the apparatus plus
the current rating of the socket-outlet.
socket-outlet shall have a rating equal to the
rated current consumption of the apparatus plus
the current rating of the socket-outlet.
N/A
14.6.6
Add: A mains switch shall comply with (a), (b) or (c)
. The contacts of a mains relay shall comply with
(a), (b) or (d). A switch that controls a mains
receptacle shall comply with (b) and a relay that
controls a mains receptacle shall comply with (b)
or (d).
. The contacts of a mains relay shall comply with
(a), (b) or (d). A switch that controls a mains
receptacle shall comply with (b) and a relay that
controls a mains receptacle shall comply with (b)
or (d).
N/A
14.6.6a
Add: Switch or relay contacts to have current rating
equal to or greater than 1.414 times the inrush
current of the apparatus
equal to or greater than 1.414 times the inrush
current of the apparatus
N/A
Page 8 of 16
Report No.: 171153
ATTACHMENT 5
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
14.6.6b
Add: Switch or relay to be TV rated.
N/A
14.6.6c
Add: Switch is located on the back of apparatus an
d is not operable from a remote control.
d is not operable from a remote control.
N/A
14.6.6d
Add: Relay is to be subjected to the endurance test.
N/A
14.6.6.1
Add: Peak Inrush current test
N/A
14.6.6.2
Add: Relay endurance test
N/A
14.6.7
Add: Double pole switch controlling a.c. and d.c. cir
cuits shall be suitable for the application.
cuits shall be suitable for the application.
N/A
14.7
Add to the end of the 2nd paragraph “…except that
the jointed test finger to in 9.1.1 is used to
determine accessibility (IEC 60950, 2.8.2) and
interlock operation (IEC 60950, 2.8.3).”
the jointed test finger to in 9.1.1 is used to
determine accessibility (IEC 60950, 2.8.2) and
interlock operation (IEC 60950, 2.8.3).”
No interlock
N/A
14.10.6
Add: “An apparatus intended for use with an
external battery shall be provided with an
overcurrent protective device in the battery-
supply circuit.”
external battery shall be provided with an
overcurrent protective device in the battery-
supply circuit.”
No battery
N/A
14.11
Add: “Component power supplies and their
optocouplers complying with the construction and
test requirements of UL 1310, UL 1950 Third
Edition, or UL 60950 are considered to fulfill the
test requirements on the clause.”
Optocouplers bridging reinforced insulation shall
comply with requirements for double protection as
specified in UL 1577. 4th paragraph reads:
“External clearances and creepage distances of
optocouplers shall comply with 13.1.”
optocouplers complying with the construction and
test requirements of UL 1310, UL 1950 Third
Edition, or UL 60950 are considered to fulfill the
test requirements on the clause.”
Optocouplers bridging reinforced insulation shall
comply with requirements for double protection as
specified in UL 1577. 4th paragraph reads:
“External clearances and creepage distances of
optocouplers shall comply with 13.1.”
Optocouplers, UR
P
14.12
Replace
“IEC 61051-2” with “UL 1449” and “IEC 60707”
with “UL 94.” Delete all references to “IEC 60151”.
“IEC 61051-2” with “UL 1449” and “IEC 60707”
with “UL 94.” Delete all references to “IEC 60151”.
No varistor
N/A
15.1.1
Add: “Attachment plug shall have a current rating
no less than 125% of the current drawn under
normal operating conditions and a voltage rating
appropriate for the rated voltage of the apparatus.
no less than 125% of the current drawn under
normal operating conditions and a voltage rating
appropriate for the rated voltage of the apparatus.
Current rating of the attachment
plug have > 125% of apparatus
rated current.
rated current.
P
Attachment plugs for use on more than one supply
voltage by means of a voltage selector shall be
rated for the voltage, which the apparatus is
intended to be connected when it is shipped from
the factory.
voltage by means of a voltage selector shall be
rated for the voltage, which the apparatus is
intended to be connected when it is shipped from
the factory.
No selector
N/A
Page 9 of 16
Report No.: 171153
ATTACHMENT 5
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
Attachment plug cap shall be polarized when the
apparatus is provided with a manually operated,
line connected, single-pole switch; Edison-base
lampholder; or a 15 or 20 A socket outlet.”
apparatus is provided with a manually operated,
line connected, single-pole switch; Edison-base
lampholder; or a 15 or 20 A socket outlet.”
Polarized plug cap.
P
15.1.2
Delete reference to “Banana” plug in the Note.
Built-in type speaker
N/A
15.1.3.1
Add: “An audio amplifier having an open-circuit
audio output voltage not limited to 120 V that is
permanently connected to the mains shall be
provided with a means for connection complying
with U.21.1.1 – U.21.1.7 and wire-binding screws
No. 6-32 or larger complying with U.21.3.1 –
U.21.3.5, or quick-connect terminals, or leads.
Quick Connect Terminal shall comply with the
following:
a) Male tabs firmly mounted in place,
b) Mating female connectors shall be provided with
the apparatus,
c) Strain Relief Test of Clause 16.5,
d) Installation instructions shall be provided for
assembly of terminal to conductor and strain relief,
e) Terminals shall be appropriate for use with the
size and type of wire specified.”
audio output voltage not limited to 120 V that is
permanently connected to the mains shall be
provided with a means for connection complying
with U.21.1.1 – U.21.1.7 and wire-binding screws
No. 6-32 or larger complying with U.21.3.1 –
U.21.3.5, or quick-connect terminals, or leads.
Quick Connect Terminal shall comply with the
following:
a) Male tabs firmly mounted in place,
b) Mating female connectors shall be provided with
the apparatus,
c) Strain Relief Test of Clause 16.5,
d) Installation instructions shall be provided for
assembly of terminal to conductor and strain relief,
e) Terminals shall be appropriate for use with the
size and type of wire specified.”
No 120V audio
N/A
15.1.3.2
Add: "Audio amplifiers having an audio output not
limited to 120 V that are connected to the mains
by a flexible cord shall have suitable cord or
provision for field installation or a receptacle for
plug-in connections."
limited to 120 V that are connected to the mains
by a flexible cord shall have suitable cord or
provision for field installation or a receptacle for
plug-in connections."
No 120V audio
N/A
15.2
Add after 3rd paragraph:
“The earthing conductor in a supply cord, or in an in
terconnecting cable shall have an equivalent or
larger cross-sectional area that the current-carrying
conductors in the supply cord or cable.
With reference to earthing conductors, the
insulation color may be green or green/yellow.
“The earthing conductor in a supply cord, or in an in
terconnecting cable shall have an equivalent or
larger cross-sectional area that the current-carrying
conductors in the supply cord or cable.
With reference to earthing conductors, the
insulation color may be green or green/yellow.
Class II apparatus
N/A
15.3.5
Revise 2nd paragraph to read: “For rated currents
exceeding 13 A, reference is made to Article 310
of the National Electrical Code, ANSI/NFPA 70.”
Table 15 - Replace with: “Nominal cross-sectional
area AWG“ and modify values.
exceeding 13 A, reference is made to Article 310
of the National Electrical Code, ANSI/NFPA 70.”
Table 15 - Replace with: “Nominal cross-sectional
area AWG“ and modify values.
Appliance inlet provided.
N/A
Page 10 of 16
Report No.: 171153
ATTACHMENT 5
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065J
15.4
Add: ”Component power supply adaptors complyin
g with the construction and test requirements of UL
1310, UL 1950 Third Edition, or UL 60950 are
considered to fulfill the test requirements on the
clause.”
g with the construction and test requirements of UL
1310, UL 1950 Third Edition, or UL 60950 are
considered to fulfill the test requirements on the
clause.”
N/A
16.1
Modification: Mains supply flexible cords shall
comply with UL 817, be marked VW-1, and have
an ampacity not less than the current drawn by the
apparatus. Delete references to IEC 602227, 6024
5
and 60173.
Table 17A - Add: Types of cords and cord lengths
for various types of apparatus.
comply with UL 817, be marked VW-1, and have
an ampacity not less than the current drawn by the
apparatus. Delete references to IEC 602227, 6024
5
and 60173.
Table 17A - Add: Types of cords and cord lengths
for various types of apparatus.
Considered
P
16.2
An integral earthing conductor shall be at least the
same size as the other cord conductors. Substitute
“IEC 60950, table 3B” with “Article 400 of the
National Electrical Code”.
Table 18 – Replace with “Wire sizes of external
flexible cords” Upper current limit in column 1
increased from 16 to 30 A and “AWG” wire sizes
added.
same size as the other cord conductors. Substitute
“IEC 60950, table 3B” with “Article 400 of the
National Electrical Code”.
Table 18 – Replace with “Wire sizes of external
flexible cords” Upper current limit in column 1
increased from 16 to 30 A and “AWG” wire sizes
added.
Class II apparatus
N/A
16.3
Add: c) Flexible cords not complying with 16.1, use
d as connection between the apparatus and other a
pparatus used in combination with it, shall be mark
ed VW-1.
d as connection between the apparatus and other a
pparatus used in combination with it, shall be mark
ed VW-1.
N/A
17.8
Expanded to include all cart/stand parts supplied by
the manufacturer, such as casters and brackets.
Suitable assembly instructions required.
Add: "Relevant fixing means are not required when
installation is to be done by a skilled person."
the manufacturer, such as casters and brackets.
Suitable assembly instructions required.
Add: "Relevant fixing means are not required when
installation is to be done by a skilled person."
No accessory
N/A
17.10
Add: Aluminum conductors used as internal wiring
shall be terminated by a method capable of being
used in the combination of metals involved at the c
onnection point.
shall be terminated by a method capable of being
used in the combination of metals involved at the c
onnection point.
N/A
17.11
Add: An accessory shall be investigated to
determine that: a) The accessory, and the combinat
ion of the accessory and the apparatus shall prese
nt no hazard in the sense of this standard and b) T
he accessory is provided with installation instructio
ns.
determine that: a) The accessory, and the combinat
ion of the accessory and the apparatus shall prese
nt no hazard in the sense of this standard and b) T
he accessory is provided with installation instructio
ns.
N/A
Click on the first or last page to see other ON BEAT XTREME (serv.man8) service manuals if exist.