JBL ENCOUNTER (serv.man4) EMC - CB Certificate ▷ View online
- Page 49 of 51 -
www.nemko.com
Report No. 27772
TRF No.:IECEN60950_1B
4.5
TABLE: maximum temperatures
P
test voltage (V) ..............................:
18
VAC
—
t
amb1
(
°
C) Normal.............................:
25
—
t
amb2
(
°
C) Blocked Vent ....................:
25
—
maximum temperature T of part/at:
T (
°
C)
allowed
T
max
(
°
C)
C16 (105ºC)
43
42
105
C64 (105ºC)
43
43
105
C56 (105ºC)
46
47
105
C78 (85ºC)
50
52
85
C79 (105ºC)
47
48
105
PCB under U14 (130ºC)
66
72
130
PCB under U15 (130ºC)
64
68
130
Power input connector (70ºC)
40
38
70
supplementary information:
temperature T of winding:
R
1
(
Ω
)
R
2
(
Ω
)
T (
°
C)
allowed
T
max
(
°
C)
insulation
class
N/A
supplementary information:
4.5.2
TABLE: ball pressure test of thermoplastic parts
N/A
allowed impression diameter (mm) ..................... :
≤
2 mm
—
part
test temperature (
°
C) impression diameter
(mm)
supplementary information:
- Page 50 of 51 -
www.nemko.com
Report No. 27772
TRF No.:IECEN60950_1B
4.7
TABLE: resistance to fire
N/A
part
manufacturer of material
type of material
thickness
(mm)
flammability
class
supplementary information:
5.1
TABLE: touch current measurement
N/A
Measured between:
Measured
(mA)
Limit
(mA)
Comments/conditions
supplementary information:
5.2
TABLE: electric strength tests, impulse tests and voltage surge tests
N/A
test voltage applied between:
test voltage (V)
a.c. / d.c.
breakdown
Yes / No
supplementary information
5.3
TABLE: fault condition tests
P
ambient temperature (
°
C) ................................. :
25
—
model/type of power supply .............................. :
—
—
manufacturer of power supply ........................... :
—
—
rated markings of power supply ......................... :
—
—
component
No.
No.
fault
test voltage
(V)
test time
fuse
No.
No.
fuse current
(A)
result
—
Top port on
subwoofer
blocked.
subwoofer
blocked.
18 VAC
4 hours
—
1.45
No effect. No significant
rise in temperatures.
Temperatures also in table
4.5. No hazard.
rise in temperatures.
Temperatures also in table
4.5. No hazard.
supplementary information:
- Page 51 of 51 -
www.nemko.com
Report No. 27772
TRF No.:IECEN60950_1B
C.2
TABLE: transformers
N/A
Loc.
Tested ins ulation
Working
voltage
peak / V
(2.10.2)
voltage
peak / V
(2.10.2)
Working
voltage
rms / V
(2.10.2)
voltage
rms / V
(2.10.2)
Required
electric
strength
(5.2)
electric
strength
(5.2)
Required
clearance /
mm
(2.10.3)
clearance /
mm
(2.10.3)
Required
creepage
distance /
mm
(2.10.4)
creepage
distance /
mm
(2.10.4)
Required
distance
thr. insul.
(2.10.5)
distance
thr. insul.
(2.10.5)
*
Loc.
Tested insulation
Test
voltage/ V
voltage/ V
Measured
clearance /
mm
clearance /
mm
Measured
creepage
dist./ mm
creepage
dist./ mm
Measured
distance
thr. insul. /
mm;
number of
layers
distance
thr. insul. /
mm;
number of
layers
supplementary information:
IEC 60950-1 1st. Ed, 2001
- Page 1 of 6 -
Order No.
27772
APPENDIX: AUSTRALIA DEVIATIONS
Test results according to CB BULLETIN No. 107A, May 2004.
Variations to IEC 60950-1:2001 for application in Australia and New Zealand
Clause
Requirement - Test
Result - Remark
Ver-
dict
ZZ.1
Introduction
This Annex sets out variations between this Standard and IEC 60950-1:2001. These variations indicate
national variations for purposes of the IECEE CB Scheme and will be published in the IECEE CB Bulletin.
These variations are indicated within the body of the Standard.
national variations for purposes of the IECEE CB Scheme and will be published in the IECEE CB Bulletin.
These variations are indicated within the body of the Standard.
ZZ.2
Variations
The variations are as follows:
1.2
Between the definitions for ‘Person, service’
and ‘Range, rated frequency’ insert the
following:
Potential ignition source 1.2.12.201
and ‘Range, rated frequency’ insert the
following:
Potential ignition source 1.2.12.201
Considered.
—
1.2.12.15
After the definition of 1.2.12.15, add the
following:
1.2.12.201 potential ignition source: Possible
fault which can start a fire if the open-circuit
voltage measured across an interruption or
faulty contact exceeds a value of 50 V (peak)
a.c. or d.c. and the product of the peak value of
this voltage and the measured r.m.s current
under normal operating conditions exceeds 15
VA.
Such a faulty contact or interruption in an
electrical connection includes those which may
occur in conductive patterns on printed boards.
following:
1.2.12.201 potential ignition source: Possible
fault which can start a fire if the open-circuit
voltage measured across an interruption or
faulty contact exceeds a value of 50 V (peak)
a.c. or d.c. and the product of the peak value of
this voltage and the measured r.m.s current
under normal operating conditions exceeds 15
VA.
Such a faulty contact or interruption in an
electrical connection includes those which may
occur in conductive patterns on printed boards.
NOTE 201 An electronic protection circuit may
be used to prevent such a fault from becoming a
POTENTIAL IGNITION SOURCE.
be used to prevent such a fault from becoming a
POTENTIAL IGNITION SOURCE.
NOTE 202 This definition is from AS/NZS
60065:2003.
60065:2003.
Considered.
—
1.5.1
Add the following to the end of first paragraph:
‘or the relevant Australian/New Zealand
Standard’.
‘or the relevant Australian/New Zealand
Standard’.
All critical components are IEC, UL
or CSA certified.
or CSA certified.
P
1.5.2
Add the following to the end of first and third
dash items:
‘or the relevant Australian/New Zealand
Standard’.
dash items:
‘or the relevant Australian/New Zealand
Standard’.
All critic al components are IEC, UL
or CSA certified.
or CSA certified.
P
2.1
Delete the Note.
—
3.2.3
Delete Note 2.
—
Click on the first or last page to see other ENCOUNTER (serv.man4) service manuals if exist.