Harman Kardon SB 16 (serv.man9) EMC - CB Certificate ▷ View online
Clause
Requirement - Test
Result - Remark
Verdict
TÜV SÜD Product Service GmbH
Report reference No.:081-61102-000
Electrical Safety
F10Y2-X dev.DOC
Ridlerstr. 65
2006-11-02
D-80339 München
Page 37 of 52
Test Report National land Group Differences IEC 60065 7
th
Ed. Rev. 00 / 2006-02
14.12
- Replace “IEC 61051-2” with “UL 1449” and “IEC
60707” with “UL 94.” Delete all references to “IEC
60151”.15.1.1 – Add: “Attachment plug shall
have a current rating no less than 125% of the
current drawn under normal operating conditions
and a voltage rating appropriate for the rated
voltage of the apparatus.
60707” with “UL 94.” Delete all references to “IEC
60151”.15.1.1 – Add: “Attachment plug shall
have a current rating no less than 125% of the
current drawn under normal operating conditions
and a voltage rating appropriate for the rated
voltage of the apparatus.
Attachment plugs for use on more than one
supply voltage by means of a voltage selector
shall be rated for the voltage, which the
apparatus is intended to be connected when it is
shipped from the factory. Attachment plug cap
shall be polarized when the apparatus is
provided with a manually operated, line
connected, single-pole switch; Edison-base
lampholder; or a 15 or 20 A socket outlet.”
supply voltage by means of a voltage selector
shall be rated for the voltage, which the
apparatus is intended to be connected when it is
shipped from the factory. Attachment plug cap
shall be polarized when the apparatus is
provided with a manually operated, line
connected, single-pole switch; Edison-base
lampholder; or a 15 or 20 A socket outlet.”
N
15.1.2
- Delete reference to “Banana” plug in the Note.
Considered. P
15.1.3.1
- Add: “An audio amplifier having an open-circuit
audio output voltage not limited to 120 V that is
permanently connected to the mains shall be
provided with a means for connection complying
with U.21.1.1 – U.21.1.7 and wire-binding screws
No. 6-32 or larger complying with U.21.3.1 –
U.21.3.5, or quick-connect
audio output voltage not limited to 120 V that is
permanently connected to the mains shall be
provided with a means for connection complying
with U.21.1.1 – U.21.1.7 and wire-binding screws
No. 6-32 or larger complying with U.21.3.1 –
U.21.3.5, or quick-connect
terminals, or leads. Quick Connect Terminal shall
comply with the following: a) Male tabs firmly
mounted in place, b) Mating female connectors
shall be provided with the apparatus, c) Strain
Relief Test of Clause 16.5, d) Installation
instructions shall be provided for assembly of
terminal to a conductor and strain relief, e)
Terminals shall be appropriate for use with the
size and type of wire specified.”
comply with the following: a) Male tabs firmly
mounted in place, b) Mating female connectors
shall be provided with the apparatus, c) Strain
Relief Test of Clause 16.5, d) Installation
instructions shall be provided for assembly of
terminal to a conductor and strain relief, e)
Terminals shall be appropriate for use with the
size and type of wire specified.”
N
15.1.3.2
- Add: "Audio amplifiers having an audio output
not limited to 120 V that are connected to the
mains by a flexible cord shall have suitable cord
or provision for field installation or a receptacle
for plug-in connections."
not limited to 120 V that are connected to the
mains by a flexible cord shall have suitable cord
or provision for field installation or a receptacle
for plug-in connections."
N
15.2
- Add after 3rd paragraph: “The earthing
conductor in a supply cord, or in an
interconnecting cable shall have an equivalent or
larger cross-sectional area that the current-
carrying conductors in the supply cord or cable.
With reference to earthing conductors, the
insulation color may be green or green/yellow.
conductor in a supply cord, or in an
interconnecting cable shall have an equivalent or
larger cross-sectional area that the current-
carrying conductors in the supply cord or cable.
With reference to earthing conductors, the
insulation color may be green or green/yellow.
Class II type equipment.
N
Clause
Requirement - Test
Result - Remark
Verdict
TÜV SÜD Product Service GmbH
Report reference No.:081-61102-000
Electrical Safety
F10Y2-X dev.DOC
Ridlerstr. 65
2006-11-02
D-80339 München
Page 38 of 52
Test Report National land Group Differences IEC 60065 7
th
Ed. Rev. 00 / 2006-02
15.3.5
- Revise 2nd paragraph to read: “For rated
currents exceeding 13 A, reference is made to
Article 310 of the National Electrical Code,
ANSI/NFPA 70.”
currents exceeding 13 A, reference is made to
Article 310 of the National Electrical Code,
ANSI/NFPA 70.”
Table 15 - Replace with: “Nominal cross-
sectional area AWG“ and modify values.
sectional area AWG“ and modify values.
No applied for.
N
15.4
- Add: ”Component power supply adaptors
complying with the construction and test
requirements of UL 1310, UL 1950 Third Edition,
or UL 60950 are considered to fulfill the test
requirements on the clause.”
complying with the construction and test
requirements of UL 1310, UL 1950 Third Edition,
or UL 60950 are considered to fulfill the test
requirements on the clause.”
Ditto. N
16.1
- Modification: Mains supply flexible cords shall
comply with UL 817, be marked VW-1, and have
an ampacity not less than the current drawn by
the apparatus. Delete references to IEC 602227,
60245 and 60173.
comply with UL 817, be marked VW-1, and have
an ampacity not less than the current drawn by
the apparatus. Delete references to IEC 602227,
60245 and 60173.
Table 17A - Add: Types of cords and cord
lengths for various types of apparatus.
lengths for various types of apparatus.
Ditto.
N
16.2
- An integral earthing conductor shall be at least
the same size as the other cord conductors.
Substitute “IEC 60950, table 3B” with “Article 400
of the National Electrical Code”.
the same size as the other cord conductors.
Substitute “IEC 60950, table 3B” with “Article 400
of the National Electrical Code”.
Table 18 – Replace with “Wire sizes of external
flexible cords” Upper current limit in column 1
increased from 16 to 30 A and “AWG” wire sizes
added.
flexible cords” Upper current limit in column 1
increased from 16 to 30 A and “AWG” wire sizes
added.
Ditto.
N
16.3
- Add: c) Flexible cords not complying with 16.1,
used as connection between the apparatus and
other apparatus used in combination with it, shall
be marked VW-1.
used as connection between the apparatus and
other apparatus used in combination with it, shall
be marked VW-1.
Ditto.
N
17.8
- Expanded to include all cart/stand parts
supplied by the manufacturer, such as casters
and brackets.
supplied by the manufacturer, such as casters
and brackets.
Suitable assembly instructions required. Add:
"Relevant fixing means are not required when
installation is to be done by a skilled person."
"Relevant fixing means are not required when
installation is to be done by a skilled person."
Added. P
17.10
- Add: Aluminum conductors used as internal
wiring shall be terminated by a method capable
of being used in the combination of metals
involved at the connection point.
wiring shall be terminated by a method capable
of being used in the combination of metals
involved at the connection point.
No applied for.
N
17.11
- Add: An accessory shall be investigated to
determine that: a) The accessory, and the
combination of the accessory and the apparatus
shall present no hazard in the sense of this
standard and b) The accessory is provided with
installation instructions.
determine that: a) The accessory, and the
combination of the accessory and the apparatus
shall present no hazard in the sense of this
standard and b) The accessory is provided with
installation instructions.
Considered. P
Clause
Requirement - Test
Result - Remark
Verdict
TÜV SÜD Product Service GmbH
Report reference No.:081-61102-000
Electrical Safety
F10Y2-X dev.DOC
Ridlerstr. 65
2006-11-02
D-80339 München
Page 39 of 52
Test Report National land Group Differences IEC 60065 7
th
Ed. Rev. 00 / 2006-02
17.11.1
- Add: The installation of an accessory of a
skilled person shall be such that: a) The
mechanical positioning is accomplished by
means of tools normally available or by means of
special tools provided by the organization
responsible for providing the apparatus as part of
the installation kit, and b) The electrical
connections are made by using existing terminals
and connections in the apparatus or the building
wiring.
skilled person shall be such that: a) The
mechanical positioning is accomplished by
means of tools normally available or by means of
special tools provided by the organization
responsible for providing the apparatus as part of
the installation kit, and b) The electrical
connections are made by using existing terminals
and connections in the apparatus or the building
wiring.
Added. P
18
- Modification: Non-intrinsically protected picture
tubes shall comply with 18.1, 18.2.2 and 18.3.
tubes shall comply with 18.1, 18.2.2 and 18.3.
Intrinsically protected picture tubes shall comply
with UL 1418 or UL 61965.
with UL 1418 or UL 61965.
Add: “A bulb of a picture tube having a face
diameter of 7.5 cm or more shall be mounted in
an enclosure.
diameter of 7.5 cm or more shall be mounted in
an enclosure.
The enclosure shall have no opening that
exceeds 130 mm2 unless the minor dimension of
the opening is 10 mm or less.”
exceeds 130 mm2 unless the minor dimension of
the opening is 10 mm or less.”
No applied for.
N
18.1
- All tubes shall be mounted such that the
enclosure of the apparatus protects the tube
against the effects of implosion. Delete reference
to clause 18.2.
enclosure of the apparatus protects the tube
against the effects of implosion. Delete reference
to clause 18.2.
18.2, 18.2.1, and 18.2.3 are deleted..19 - Add
reference to 19.2.1. The test of 19.3 is conducted
on 1) apparatus with direct view CRT with 48 cm
diagonal min., 2) apparatus, other than a
speaker, with a mass greater than 47 kg, and 3)
apparatus, other than a speaker, with a mass or
25 kg or greater and a height of 1 m or more. The
tests in 19.1, 19.2 and 19.3 shall not cause the
apparatus to overturn. During the test of 19.2.1,
the apparatus shall not slide.
reference to 19.2.1. The test of 19.3 is conducted
on 1) apparatus with direct view CRT with 48 cm
diagonal min., 2) apparatus, other than a
speaker, with a mass greater than 47 kg, and 3)
apparatus, other than a speaker, with a mass or
25 kg or greater and a height of 1 m or more. The
tests in 19.1, 19.2 and 19.3 shall not cause the
apparatus to overturn. During the test of 19.2.1,
the apparatus shall not slide.
No CRT.
N
19.2.1
- Add: Slide test requirements.
No applied for.
N
19.3
– Replace by Horizontal force stability test
requirements.
requirements.
Table 20 – Add values for horizontal force test
Ditto. N
19.6.
-Add: “or equipment rack mounting”.
Ditto. N
20.1a
- Delete
N
20.1b
- Replace “IEC 60707” with “UL 94”
Add: “-parts such as protection TV lenses,
loudspeaker parts, external accessories, and
fibrous materials less then 0.25 mm thick.”
loudspeaker parts, external accessories, and
fibrous materials less then 0.25 mm thick.”
Replaced. N
Clause
Requirement - Test
Result - Remark
Verdict
TÜV SÜD Product Service GmbH
Report reference No.:081-61102-000
Electrical Safety
F10Y2-X dev.DOC
Ridlerstr. 65
2006-11-02
D-80339 München
Page 40 of 52
Test Report National land Group Differences IEC 60065 7
th
Ed. Rev. 00 / 2006-02
20.1.2
- Revise text to read: “Sleeving, extruded tubing
and insulation on wiring shall be rated VW-1
under following conditions: a) wiring located in a
circuit that is considered a potential ignition
source” or b) wiring not located in a circuit that is
a potential ignition source but is in contact with
wiring located in a circuit that is a potential
ignition source. ”Tape should be flame retardant.”
and insulation on wiring shall be rated VW-1
under following conditions: a) wiring located in a
circuit that is considered a potential ignition
source” or b) wiring not located in a circuit that is
a potential ignition source but is in contact with
wiring located in a circuit that is a potential
ignition source. ”Tape should be flame retardant.”
Delete Note and add: “Tape in contact with parts
of circuits that are potential ignition sources shall
be flame retardant.
of circuits that are potential ignition sources shall
be flame retardant.
Considered. N
20.1.3
- Replace 1st paragraph with: “Base material of
printed wiring boards, on which the available
power as the connection exceeds 15 W or the
operating voltage exceeds 50 V a.c. or d.c under
normal operating conditions, shall be of
flammability category V-1 or better according to
UL 94.”
printed wiring boards, on which the available
power as the connection exceeds 15 W or the
operating voltage exceeds 50 V a.c. or d.c under
normal operating conditions, shall be of
flammability category V-1 or better according to
UL 94.”
In 2nd paragraph replace “IEC 60707” with “UL
94” and remove exception for printed boards
housed in metal enclosures.
94” and remove exception for printed boards
housed in metal enclosures.
In 3rd paragraph replace “IEC 60707” with “UL
94” and delete option to use Clause G.1 of Annex
G.
94” and delete option to use Clause G.1 of Annex
G.
Replaced. P
20.1.4
- Replace with: “Components and parts shall
comply with the relevant flammability category
according to UL 94 as specified in Table 21.
Delete all other text.
comply with the relevant flammability category
according to UL 94 as specified in Table 21.
Delete all other text.
Replaced. N
20.1.4
- Add: “Component power supplies complying
with the construction and test requirements of UL
1310, UL 1950 Third Edition, or UL 60950 are
considered to fulfill the test requirements on the
clause.”
with the construction and test requirements of UL
1310, UL 1950 Third Edition, or UL 60950 are
considered to fulfill the test requirements on the
clause.”
Table 21 - Replace complete table with new table
for “Flammability categories for components and
parts.”
for “Flammability categories for components and
parts.”
No applied for.
N
20.2.1
- Modification: 1st paragraph: “Fire enclosure
required for 1) circuits and components where
the available power exceeds 15 W, 2) inductors
and windings conductively connected to the
mains and 3) high-voltage products. The fire
enclosure shall comply with the flammability
requirements of Table 22 according to UL 94 and
746C. 2nd, 3rd, and 4th paragraphs are deleted.
required for 1) circuits and components where
the available power exceeds 15 W, 2) inductors
and windings conductively connected to the
mains and 3) high-voltage products. The fire
enclosure shall comply with the flammability
requirements of Table 22 according to UL 94 and
746C. 2nd, 3rd, and 4th paragraphs are deleted.
In 5th paragraph replace “IEC 60707 or clause
G.1 of Annex G” with “UL 94 or UL 746C.”
G.1 of Annex G” with “UL 94 or UL 746C.”
Table 22 – Add” Flammability categories for fire
enclosures.
enclosures.
N
Click on the first or last page to see other SB 16 (serv.man9) service manuals if exist.