Harman Kardon SB 16 (serv.man9) EMC - CB Certificate ▷ View online
Clause
Requirement - Test
Result - Remark
Verdict
TÜV SÜD Product Service GmbH
Report reference No.:081-61102-000
Electrical Safety
F10Y2-X dev.DOC
Ridlerstr. 65
2006-11-02
D-80339 München
Page 25 of 52
Test Report National land Group Differences IEC 60065 7
th
Ed. Rev. 00 / 2006-02
J.2
After Table J.1 the following is added: In Norway,
due to the IT power distribution system used, the
a.c. MAINS supply voltage is considered to be
equal to the line-to-line voltage, and will remain
230 V in case of a single earth fault.
due to the IT power distribution system used, the
a.c. MAINS supply voltage is considered to be
equal to the line-to-line voltage, and will remain
230 V in case of a single earth fault.
Justification:
Based on a use in Norway of an IT power
distribution system where the neutral is not
provided.
distribution system where the neutral is not
provided.
Considered. P
Annex B
Replace NOTE 1 by
In the CENELEC countries listed in IEC 62151,
special national conditions apply.
special national conditions apply.
Add the following:
All subclauses given below are subclauses of
IEC 62151:2000 (ref. Corrigendum 1 and 2 to
IEC 62151).
IEC 62151:2000 (ref. Corrigendum 1 and 2 to
IEC 62151).
Replaced. P
Subclause 4.1.1 (Corrigendum 2):
Add after the first paragraph:
NOTE - In Norway, CLASS I equipment which is
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
The marking text shall be as follows:
"Apparatet skal tilkoples jordet stikkontakt"
Subclause 5.3.1 (Corrigendum 1):
Add after the first test specifications paragraph:
Added. P
NOTE 1 In Finland, Norway and Sweden, there
are additional requirements for the insulation.
Renumber the existing note as note 2.
are additional requirements for the insulation.
Renumber the existing note as note 2.
For additional requirements for the insulation in
Sweden in the NOTE 1 the following text is
added between the first and second paragraph
(this text is identical to the text in EN 60950-
1:2001):
Sweden in the NOTE 1 the following text is
added between the first and second paragraph
(this text is identical to the text in EN 60950-
1:2001):
No TNV circuit.
N
Clause
Requirement - Test
Result - Remark
Verdict
TÜV SÜD Product Service GmbH
Report reference No.:081-61102-000
Electrical Safety
F10Y2-X dev.DOC
Ridlerstr. 65
2006-11-02
D-80339 München
Page 26 of 52
Test Report National land Group Differences IEC 60065 7
th
Ed. Rev. 00 / 2006-02
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
forming part of a component, it shall at least
consist of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or -
one layer having a distance through insulation of
at least 0,4 mm, which shall pass the electric
strength test below.
shall pass the electric strength test below, or -
one layer having a distance through insulation of
at least 0,4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES
do not exist, if the component passes the electric
strength test in the accordance with the
compliance clause below and in addition:
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES
do not exist, if the component passes the electric
strength test in the accordance with the
compliance clause below and in addition:
- passes the test and inspection criteria of 13.6
with an electric strength test of 10.3 using the
test voltage of 1,5 kV multiplied by 1,6, and
with an electric strength test of 10.3 using the
test voltage of 1,5 kV multiplied by 1,6, and
- is subject to routine testing for electric strength
during manufacturing, using a test voltage of 1,5
kV (for performance of the test see N.2.1).
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
during manufacturing, using a test voltage of 1,5
kV (for performance of the test see N.2.1).
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
No applied for.
N
A capacitor classified Y3 according to IEC
60384-14:1993, may bridge this insulation under
the following conditions:
60384-14:1993, may bridge this insulation under
the following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by
IEC 60384-14, which in addition
to the Y3 testing, is tested with an Impulse test of
2.5kV defined in IEC 62151, subclause 6.2.1;
having a capacitor classified Y3 as defined by
IEC 60384-14, which in addition
to the Y3 testing, is tested with an Impulse test of
2.5kV defined in IEC 62151, subclause 6.2.1;
- the additional testing shall be performed on all
the test specimens as described in IEC 60384-
14;
the test specimens as described in IEC 60384-
14;
- the Impulse test of 2.5kV is to be performed
before the Endurance Test in IEC 60384-14 in
the sequence of tests as
described in IEC 60384-14.
before the Endurance Test in IEC 60384-14 in
the sequence of tests as
described in IEC 60384-14.
No applied for.
N
Clause
Requirement - Test
Result - Remark
Verdict
TÜV SÜD Product Service GmbH
Report reference No.:081-61102-000
Electrical Safety
F10Y2-X dev.DOC
Ridlerstr. 65
2006-11-02
D-80339 München
Page 27 of 52
Test Report National land Group Differences IEC 60065 7
th
Ed. Rev. 00 / 2006-02
Subclause 5.3.2 (Corrigendum 1):
Add after the fourth dash:
NOTE -In Norway, exclusions are applicable for
equipment which is intended for connection to
the building installation
wiring using screw terminals or other reliable
means, and for equipment which is intended for
connection to the building installation wiring via
an industrial plug and socket -outlet or an
appliance coupler, or both, complying with IEC
60309 or with a comparable national standard.
Add after the fourth dash:
NOTE -In Norway, exclusions are applicable for
equipment which is intended for connection to
the building installation
wiring using screw terminals or other reliable
means, and for equipment which is intended for
connection to the building installation wiring via
an industrial plug and socket -outlet or an
appliance coupler, or both, complying with IEC
60309 or with a comparable national standard.
No applied for.
N
Clause
Requirement - Test
Result - Remark
Verdict
TÜV SÜD Product Service GmbH
Report reference No.:081-61102-000
Electrical Safety
F10Y2-X dev.DOC
Ridlerstr. 65
2006-11-02
D-80339 München
Page 28 of 52
Test Report National land Group Differences IEC 60065 7
th
Ed. Rev. 00 / 2006-02
SE
Annex B
Replace NOTE 1 by
In the CENELEC countries listed in IEC 62151,
special national conditions apply.
special national conditions apply.
Add the following:
All subclauses given below are subclauses of
IEC 62151:2000 (ref. Corrigendum 1 and 2 to
IEC 62151).
IEC 62151:2000 (ref. Corrigendum 1 and 2 to
IEC 62151).
Subclause 4.1.1 (Corrigendum 2):
Add after the first paragraph:
Replaced. P
NOTE - In Sweden, CLASS I equipment which is
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
The marking text shall be as follows:
"Apparaten skall anslutas till jordat uttag”
Subclause 5.3.1 (Corrigendum 1):
Add after the first test specifications paragraph:
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
capacitor complying with IEC 60384-14:1993,
subclass Y2.
No mains sock-outlet.
N
NOTE 1 In Finland, Norway and Sweden, there
are additional requirements for the insulation.
are additional requirements for the insulation.
Renumber the existing note as note 2.
For additional requirements for the insulation in
Sweden in the NOTE 1 the following text is
added between the first and second paragraph
(this text is identical to the text in EN 60950-
1:2001):
Sweden in the NOTE 1 the following text is
added between the first and second paragraph
(this text is identical to the text in EN 60950-
1:2001):
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
forming part of a component, it shall at least
consist of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation
of at least 0,4 mm, which shall pass the electric
strength test below.
shall pass the electric strength test below, or
- one layer having a distance through insulation
of at least 0,4 mm, which shall pass the electric
strength test below.
No applied for.
N
Click on the first or last page to see other SB 16 (serv.man9) service manuals if exist.