DOWNLOAD Harman Kardon HS 2X0 Service Manual ↓ Size: 889.84 KB | Pages: 64 in PDF or view online for FREE

 

Page 11 of 62                                Report No. SH10011244-001 

IEC 60065

Clause 

Requirement + Test 

Result - Remark 

Verdict 

TRF No. IEC60065J 
 
 
 

9.1.7 

Resistance to external forces 

 

Pass 

 

a) Test probe 11 of IEC 61032 for 10 s (50 N)  

No damage of enclosure and no 
hazardous live parts are 
accessible. 

Pass 

 

b) Test hook of fig. 4 for 10 s (20 N)  

No hazardous live parts are 
accessible. 

Pass 

 

c) 30 mm diameter test tool for 5 s (100 or 250 N)  

100N 

Pass 

9.2 

No hazard after removing a cover by hand  

Tools required. 

N/A 

 

10.1 

Insulation resistance (MΩ) at least 2 MΩ min. after 
surge test for basic and 4 MΩ min. for reinforced 
insulation ………………………………………………..
: 

 

Pass 

10.2 

Humidity treatment 48 h or 120 h …………………….: 40℃, 95%, 120h. 

Pass 

10.3 

Insulation resistance and dielectric strength between 
mains terminals  

(see appended table) 

Pass 

 

Insulation Resistance and dielectric strength across 
BASIC or SUPPLEMENTARY insulation (Class 1)  

Class II 

N/A 

 

Insulation resistance and dielectric strength across 
REINFORCED insulation (Class II)  

(see appended table) 

Pass 

 

11.1 

No shock hazard under fault condition  

Single fault did not cause 
excessive voltage in output 
circuits. 

Pass 

11.2 

Heating under fault condition  

 

Pass 

 

Flames extinguish within 10 seconds  

No flames 

N/A 

 

No hazard from softening solder  

No softening of solder point and 
becoming fluid 

Pass 

 

Soldered terminations not used  as protective 
mechanism  

 Pass 

11.2.1 

Measurement of temperature rises  

(see appended table) 

Pass 

11.2.2 

Temperature rise of accessible parts  

(see appended table) 

Pass 

11.2.3 

Temperature rise of parts, other than windings, 
providing electrical insulation  

(see appended table) 

Pass 

 

Temperature rise of printed circuit boards (PCB) 
exceeding the limits of table 3 by max. 100 K for 
max. 5 min  

(see appended table) 

Pass 

 

Page 12 of 62                                Report No. SH10011244-001 

IEC 60065

Clause 

Requirement + Test 

Result - Remark 

Verdict 

TRF No. IEC60065J 
 
 
 

 

a) Temperature rise of printed circuit boards (PCB) 
to 20.1.3, exceeding the limits of table 3 by not more 
than 100 K for an area not greater than 
2 cm² ………: 

         

 N/A 

 

b) Temperature rise of printed circuit boards (PCB) 
to 20.1.3 up to 300 K for an area not greater than 
2 cm² for a maximum of 5 min  

         

 N/A 

 

Meets all the special conditions if conductors on 
printed circuit boards are interrupted  

         

 N/A 

 

Class I protective earthing maintained  

Class II 

N/A 

11.2.4 

Temperature rise of parts acting as a support or  
mechanical barrier  

(see appended table) 

Pass 

11.2.5 

Temperature rise of windings  

(see appended table) 

Pass 

11.2.6 

Temperature rise of parts not subject to the limits of 
11.2.1 to 11.2.5  

(see appended table) 

Pass 

 

12.1.1 

Bump test where mass >7 kg  

Mass weight : 3.53 kg. 

Pass 

12.1.2 

Vibration test  

 

N/A 

12.1.3 

Impact hammer test  

0.5J, no hazards after the test 

Pass 

 

Steel ball test  

2J, no hazards after the test 

Pass 

12.1.4 

Drop test for portable apparatus where mass ≤ 7 kg   

N/A 

12.1.5 

Thermoplastic enclosures stress relief test  

70°C / 7 hours 

Pass 

12.2 

Fixing of knobs, push buttons, keys and levers  

 

Pass 

12.3 

Remote controls with hazardous live parts  

No remote control device with 
hazardous live parts 

N/A 

12.4 

Drawers (pull test 50 N, 10 s)  

No drawer is provided 

N/A 

12.5 

Antenna coaxial sockets providing isolation  

No antenna coaxial socket is 
provided as isolation 

N/A 

12.6 

Telescoping or rod antennas construction  

No such device 

N/A 

12.6.1 

Telescoping or rod antennas securement  

 

N/A 

 

13.1 

Clearances in accordance with 13.3  

 Pass 

 

Creepage distances in accordance with 13.4  

 

Pass 

13.2 

Determination of operating voltage  

T502: 254Vrms, 536Vp 
T503: 275Vrms, 560Vp 

Pass 

13.3 Clearances 

 

 

Pass 

13.3.1 General 

 

 

Pass 

 

Page 13 of 62                                Report No. SH10011244-001 

IEC 60065

Clause 

Requirement + Test 

Result - Remark 

Verdict 

TRF No. IEC60065J 
 
 
 

13.3.2 

Circuits conductively connected to the mains comply 
with table 8 and, where applicable, table 
9 …………..: 

(See table 13) 

Pass 

13.3.3 

Circuits not conductively connected to the mains 
comply with table 10  

Such circuits are secondary 
circuit and do not include 
hazardous voltage, no basic, 
supplementary or reinforced 
insulation required. 

N/A 

13.3.4 

Measurement of transient voltages  

 

N/A 

13.4 

Creepage distances  

 

Pass 

 

Creepage distances greater than table 11 minimum 
values  

(See table 13) 

Pass  

13.5 

Printed boards  

 

N/A 

13.5.1 

Clearances and creepage distances between 
conductors on printed circuit boards, one of which 
may be conductively connected to the mains, as in 
fig. 10  

 N/A 

13.5.2 

Type B coated printed circuit boards complying with 
IEC 60664-3 (basic insulation only)  

 N/A 

13.6 

Conductive parts along uncemented joints 
clearances and creepage distances comply with 13.3 
and 13.4  

 N/A 

 

Conductive parts along reliably cemented joints 
comply with 8.8  

 N/A 

 

Temperature cycle test and dielectric strength test  

 

N/A 

13.7 

Enclosed, enveloped or hermetically sealed parts not 
conductively connected to the mains, clearances and 
creepage distances as in table 12  

 N/A 

13.8 

Parts filled with insulating compound, meeting the 
requirements of 8.8  

Optocoupler are approved 
components.                         
(See sub-clause 14.11) 

Pass 

 

14.1 Resistors 

 

 

Pass 

 

a) Resistors between hazardous live parts and 
accessible metal parts  

R

558  

Pass 

 

b) Resistors, other than between hazardous live 
parts and accessible parts  

 N/A 

 

Resistors separately approved ……………………….: R558 approved by VDE 

Pass 

14.2 

Capacitors and RC units  

 

Pass 

 

Page 14 of 62                                Report No. SH10011244-001 

IEC 60065

Clause 

Requirement + Test 

Result - Remark 

Verdict 

TRF No. IEC60065J 
 
 
 

 Capacitors 

separately 

approved ………………...……: 

Yes  

Pass 

14.2.1 

Y capacitors tested to IEC 60384-14, 2

nd

 

edition ……: 

Y1: CY501, CY502, CY503, 
CY504 

Pass 

14.2.2 

X capacitors tested to IEC 60384-14, 2

nd

 

edition ……: 

X2: CX501, CX502, CX503 

Pass 

14.2.3 

Capacitors operating at mains frequency but not 
connected to the mains: tests for 
X2 …………………: 

No such component. 

N/A 

14.2.5 

Capacitors with volume exceeding 1750 mm³, where 
short-circuit current exceeds 0,2 A: compliance with 
IEC60384-1, 4.38 category B or 
better ………………: 

 

N/A 

 

Capacitors with volume exceeding 1750 mm³, 
mounted closer to a potential ignition source than 
table 5 permits: compliance with IEC 60 384-1, 4.38 
category B or 
better ……………………………………: 

 N/A 

 

Shielded by a barrier acc. to 20.1.4/ table 21 or 
metal …………………………………………………….
: 

No, electrolytic capacitor is fully 
shielded by metal case. 

N/A 

14.3 

Inductors and windings  

 

Pass 

 

Comply with IEC 61558-1, IEC 61558-2 
(as relevant) and clause 20.1.4  

 

N/A 

14.3.1 

Transformers and inductors marked with 
manufacturer's name and type ……………………….:

Power transformer T502, T503 

Line filter LF501, LF502  
(See appended table14) 

Pass 

 

Transformers and inductors separately approved ….: No, tested with appliance 

N/A 

14.3.2 General 

 

 

Pass 

 

Insulation material complies with clause 20.1.4  

 

Pass 

14.3.3 

Constructional requirements  

 

Pass 

14.3.3.1 

Clearances and creepage distances comply with 
clause 13  

(see appended table) 

Pass 

14.3.3.2 

Transformers meet the constructional requirements   

Pass 

14.3.4 

Separation between windings 

 

Pass