Harman Kardon GO PLAY MICRO (serv.man2) EMC - CB Certificate ▷ View online
Page 20 of 58
Report No. 15039146 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
4.3.8
Batteries
(see appended tables 4.3.8)
P
- Overcharging of a rechargeable battery
Non-rechargeable batteries
used.
used.
N/A
- Unintentional charging of a non-rechargeable
battery
battery
Tested and complied.
P
- Reverse charging of a rechargeable battery
N/A
- Excessive discharging rate for any battery
Tested and complied.
P
4.3.9
Oil and grease
N/A
4.3.10
Dust, powders, liquids and gases
No dangerous concentration,
vaporization, leakage, spillage
or corrosion likely.
vaporization, leakage, spillage
or corrosion likely.
P
4.3.11
Containers for liquids or gases
N/A
4.3.12
Flammable liquids .................................................:
N/A
Quantity of liquid (l) ...............................................:
N/A
Flash point (
°
C) .....................................................:
N/A
4.3.13
Radiation
See below.
P
4.3.13.1
General
See below.
P
4.3.13.2
Ionizing radiation
N/A
Measured radiation (pA/kg) ............................... :
N/A
Measured high-voltage (kV) ............................... :
N/A
Measured focus voltage (kV) ............................. :
N/A
CRT markings .................................................... :
N/A
4.3.13.3
Effect of ultraviolet (UV) radiation on materials
N/A
Part, property, retention after test, flammability
classification .........................................................:
classification .........................................................:
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation .......:
N/A
4.3.13.5
Lasers (including laser diodes) and LEDs
Indicating lights used only.
P
4.3.13.5.1 Lasers (including laser laser diodes)
N/A
Laser class ............................................................:
4.3.13.5.2 Light emitting diodes (LEDs)
Far lower than AEL of class 1.
P
4.3.13.6
Other types ...........................................................:
N/A
4.4
Protection against hazardous moving parts
N/A
4.4.1
General
N/A
4.4.2
Protection in operator access areas .................... :
N/A
Household and home/office document/media
shredders
shredders
(see Annex EE)
N/A
Page 21 of 58
Report No. 15039146 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
4.4.3
Protection in restricted access locations ............. :
N/A
4.4.4
Protection in service access areas
N/A
4.4.5
Protection against moving fan blades
N/A
4.4.5.1
General
N/A
Not considered to cause pain or injury. a)………….:
N/A
Is considered to cause pain, not injury. b) …………:
N/A
Considered to cause injury. c) …………:
N/A
4.4.5.2
Protection for users
N/A
Use of symbol or warning ……………………………:
N/A
4.4.5.3
Protection for service persons
N/A
Use of symbol or warning ……………………………:
N/A
4.5
Thermal requirements
P
4.5.1
General
P
4.5.2
Temperature tests
No exceeding temperature.
P
Normal load condition per Annex L ...................... :
4.5.3
Temperature limits for materials
(see appended table 4.5)
P
4.5.4
Touch temperature limits
(see appended table 4.5)
P
4.5.5
Resistance to abnormal heat ............................... :
N/A
4.6
Openings in enclosures
P
4.6.1
Top and side openings
No openings.
P
Dimensions (mm) ................................................ :
4.6.2
Bottoms of fire enclosures
No openings.
P
Construction of the bottomm, dimensions (mm) . :
4.6.3
Doors or covers in fire enclosures
N/A
4.6.4
Openings in transportable equipment
N/A
4.6.4.1
Constructional design measures
N/A
Dimensions (mm) ................................................ :
4.6.4.2
Evaluation measures for larger openings
N/A
4.6.4.3
Use of metallized parts
N/A
4.6.5
Adhesives for constructional purposes
N/A
Conditioning temperature (
°
C), time (weeks) ....... :
4.7
Resistance to fire
P
4.7.1
Reducing the risk of ignition and spread of flame
See below.
P
Page 22 of 58
Report No. 15039146 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
Method 1, selection and application of components
wiring and materials
wiring and materials
(see appended table 4.7)
P
Method 2, application of all of simulated fault
condition tests
condition tests
(see appended table 5.3)
P
4.7.2
Conditions for a fire enclosure
See below.
P
4.7.2.1
Parts requiring a fire enclosure
See below.
N/A
4.7.2.2
Parts not requiring a fire enclosure
Following parts do not require
a fire enclosure:
a fire enclosure:
Connectors in secondary
circuits supplied by limited
power source.
circuits supplied by limited
power source.
Other components in
secondary circuits supplied
by limited power source
and mounted on V-1
material.
secondary circuits supplied
by limited power source
and mounted on V-1
material.
P
4.7.3
Materials
P
4.7.3.1
General
Those components are
mounted on V-1 material and
separated from material of a
class lower than V-1 by at
least 13 mm of air.
mounted on V-1 material and
separated from material of a
class lower than V-1 by at
least 13 mm of air.
P
4.7.3.2
Materials for fire enclosures
N/A
4.7.3.3
Materials for components and other parts outside
fire enclosures
fire enclosures
N/A
4.7.3.4
Materials for components and other parts inside fire
enclosures
enclosures
N/A
4.7.3.5
Materials for air filter assemblies
N/A
4.7.3.6
Materials used in high-voltage components
N/A
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
P
5.1
Touch current and protective conductor current
Class III equipment.
Class III equipment.
N/A
5.1.1
General
N/A
5.1.2
Configuration of equipment under test (EUT)
N/A
5.1.2.1
Single connection to an a.c. mains supply
N/A
5.1.2.2
Redundant multiple connections to an a.c. mains
supply
supply
N/A
5.1.2.3
Simultaneous multiple connections to an a.c. mains
supply
supply
N/A
5.1.3
Test circuit
N/A
5.1.4
Application of measuring instrument
N/A
Page 23 of 58
Report No. 15039146 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
5.1.5
Test procedure
N/A
5.1.6
Test measurements
N/A
Supply voltage (V) .................................................:
Measured touch current (mA) ...............................:
Max. allowed touch current (mA) ..........................:
Measured protective conductor current (mA) .......:
Max. allowed protective conductor current (mA) ...:
5.1.7
Equipment with touch current exceeding 3,5 mA
N/A
5.1.7.1
General .................................................................:
N/A
5.1.7.2
Simultaneous multiple connections to the supply
N/A
5.1.8
Touch currents to telecommunication networks and
cable distribution systems and from
telecommunication networks
cable distribution systems and from
telecommunication networks
N/A
5.1.8.1
Limitation of the touch current to a
telecommunication network or to a cable distribution
system
telecommunication network or to a cable distribution
system
N/A
Supply voltage (V) .................................................:
Measured touch current (mA) ...............................:
Max. allowed touch current (mA) ..........................:
5.1.8.2
Summation of touch currents from
telecommunication networks
telecommunication networks
N/A
a) EUT with earthed telecommunication ports ......:
N/A
b) EUT whose telecommunication ports have no
reference to protective earth
reference to protective earth
N/A
5.2
Electric strength
Class III equipment
Class III equipment
N/A
5.2.1
General
(see appended table 5.2)
N/A
5.2.2
Test procedure
N/A
5.3
Abnormal operating and fault conditions
P
5.3.1
Protection against overload and abnormal operation (see appended table 5.3)
P
5.3.2
Motors
(see appended Annex B)
N/A
5.3.3
Transformers
(see appended Annex C)
N/A
5.3.4
Functional insulation ..............................................:
Functional insulation complied
with the requirements c).
with the requirements c).
P
5.3.5
Electromechanical components
N/A
5.3.6
Audio amplifiers in ITE ..........................................:
(see appended table 5.3)
P
Click on the first or last page to see other GO PLAY MICRO (serv.man2) service manuals if exist.