DOWNLOAD Sony HDR-SR11 / HDR-SR11E / HDR-SR12 / HDR-SR12E (serv.man3) Service Manual ↓ Size: 760.69 KB | Pages: 48 in PDF or view online for FREE

6-8

HDR-SR11/SR11E/SR12/SR12E_ADJ

Before performing the adjustment, “Setting of Adjustment Mode”
is required.

[Setting method]
1) Connect the Camcorder to the PC with a USB cable, and turn

on the power switch.

2) The USB SELECT menu will appear on the LCD screen of

the Camcorder, and then select “COMPUTER” to establish
the connection.

3) Start the Automatic Adjustment Program, and click the [Con-

nect] button on the Main Menu screen.

4) When the following message is displayed, turn off and on again

the power switch of the Camcorder.

Turning off and on the power switch causes the
Camcorder to be switched to the Adjustment Mode.
After the Camcorder restarted, click the [OK] button in
the message window.

5) Upon successful completion of the settings in the Adjustment

Mode, the operation of each button on the Main Menu screen
is enabled.

To finish the adjustment, be sure to perform “Release of Adjust-
ment Mode”.

[Releasing method]
1) Click the [END] button on the Main Menu screen.
2) When the following message is displayed, releasing of adjust-

ment mode has completed. Click the [OK] button in the mes-
sage window to exit the Automatic Adjustment Program.

The Camcorder switches to the normal mode by turn-
ing off and on the power switch. After the adjustment
finished, turn off and on again the power switch of the
Camcorder to confirm that the USB SELECT menu is
displayed.

6-9

HDR-SR11/SR11E/SR12/SR12E_ADJ

When the HDD is replaced, the following VBScript files are used.
The Automatic Adjustment Program (HDR-SR11 Series Auto-Adj
Ver_1.[]r[][].exe) is not used.
• CheckHDDError_After2008.vbe
• SetFactoryCheckDefault_After2008.vbe
• SetFactoryCheckFull_After2008.vbe
• ExecAfterFactoryCheck_2008.vbe

For the VBScript files ([][][][][][][].vbe), the program is executed
by double-clicking the file.

The VBScript files can only be used on the PC in which
the SeusEX is installed.

The VBScript file to be used must include 2008 in the
file name.

6-10

HDR-SR11/SR11E/SR12/SR12E_ADJ

Message is checked.

When message is 
“No Error”

When message is 
“Error Detected”

Connect the camcorder to the PC 
with a USB cable, and turn on the 
power switch.

The USB SELECT menu will appear 
on the LCD screen of the camcorder, 
and the select “USB CONNECT” to 
establish the connection.

Execte the “CheckHDDError_After2008.vbe”.
(Double-click the file.)

Replacing the HDD is unneccessary.

Start

End

60GB: HDR-SR11/SR11E
120GB: HDR-SR12/SR12E

Select correct capacity and retry, if the HDD capacity
setting was wrong.

6-11

HDR-SR11/SR11E/SR12/SR12E_ADJ

During the execution of Factory Check, the LCD screen of
the camcorder becomes gray, and the ACCESS lamp be-
comes dark and light.
When the Factory Check finished, the LCD screen changes
as follows:

When Factory Check is OK: Camera image display
When Factory Check is NG: Blue display

Is replacement HDD new one?

No
Reused HDD

Yes
New HDD

Turn off the power of camcorder.

Turning on the power of camcorder 

will start automatic Factory Check.

Wait until Factory Check completed. (Note)

[EST. PROCESS TIME]

Default: 6 min.
Full:

            40GB   About 2 hour  36 min.
            60GB   About 3 hour  36 min.
            120GB  About 7 hour  15 min.

Replace the HDD.

Execte the 
“SetFactoryCheckDefault_After2008.vbe”.
(Double-click the file.)

Wait until “JOB Success” 
message is displayed. 
(several seconds)

Wait until “JOB Success” 
message is displayed. 
(several seconds)

Wait until “JOB Success” 
message is displayed. 
(several seconds)

Execte the 
“SetFactoryCheckFull_After2008.vbe”.
(Double-click the file.)

Execte the 
“ExecAfterFactoryCheck_2008.vbe”.
(Double-click the file.)