Sony HDR-SR11 / HDR-SR11E / HDR-SR12 / HDR-SR12E (serv.man3) Service Manual ▷ View online
6-32
HDR-SR11/SR11E/SR12/SR12E_ADJ
11-3. GYRO Sensor Sensitivity Adjustment
[Adjusting method]
1) Click the [Start] button of Camera Adjustment 8, and the fol-
1) Click the [Start] button of Camera Adjustment 8, and the fol-
lowing screen will appear.
2) Input the sensitivity of respective sensors (S
9001
, S
9002
) read at
“Preparation” into the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.
3) Input the PITCH/YAW data of lens (L
1
, L
2
) read at “Prepara-
tion” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.
Note:
In order to get the correct value for the adjustment, it is
necessary to input a decimal point (“period” or “com-
ma”) as same format as windows setting because “Nu-
meric Value Format” depend on the language. (F:123
456 789,00, GB:123,456,789.00, D:123.456.789,00)
“Numeric Value Format” setting is available in “Con-
trol Panel”-“Regional and Language Options”.
necessary to input a decimal point (“period” or “com-
ma”) as same format as windows setting because “Nu-
meric Value Format” depend on the language. (F:123
456 789,00, GB:123,456,789.00, D:123.456.789,00)
“Numeric Value Format” setting is available in “Con-
trol Panel”-“Regional and Language Options”.
4) Click the [OK] button, and the adjustment data is then calcu-
lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.
sult is written to the memory in the camera.
5) Upon successful completion of the data writing, the following
massage will be displayed, and then turn off the power of cam-
era and turn it on again.
era and turn it on again.
6) After the Camera started, click the [OK] button of the mes-
sage, and the data value will be clecked. If the data value is
normal, the following massage will be displayed. Check that
the steady shot function operates normally.
normal, the following massage will be displayed. Check that
the steady shot function operates normally.
11-2. Preparation when the lens is replaced
Note down the PITCH/YAW data on the replacement lens for repair.
Adjustment Block
11
Adjustment Page
8F
Adjustment Address
FF70, FF71
Note:
The PITCH/YAW data of lens is written only repair parts.
Preparation:
1) Read the PITCH data written on repair parts, and named this
1) Read the PITCH data written on repair parts, and named this
as L
1
.
2) Read the YAW data written on repair parts, and named this as
L
2
.
Fig. 6-1-19
YAW data
t
L
2
PITCH/YAW Data
PITCH data
t
L
1
P.PP / Y.YY
P.PP / Y.YY
6-33
HDR-SR11/SR11E/SR12/SR12E_ADJ
1-8.
LCD/EVF SYSTEM ADJUSTMENTS
1.
Function of Each Button on LCD/EVF System
Adjustment Screen
Adjustment Screen
Click the [LCD/EVF SYSTEM ADJUSTMENT] button on the Main
Menu screen, and the “LCD/EVF SYSTEM ADJUSTMENT”
screen in Fig. 6-1-20 will appear.
Menu screen, and the “LCD/EVF SYSTEM ADJUSTMENT”
screen in Fig. 6-1-20 will appear.
Fig. 6-1-20
1
[To Menu] button
The Main Menu screen comes back.
The Main Menu screen comes back.
2
[Start] button
Each adjustment “LCD Adjustment”, “EVF Adjustment” or
“Touch Panel Adjustment” starts.
Each adjustment “LCD Adjustment”, “EVF Adjustment” or
“Touch Panel Adjustment” starts.
2.
Adjustment Items of LCD/EVF System Adjustment
The adjustment items of LCD/EVF system adjustment are as listed
in Table 6-1-5. The Automatic Adjustment Program executes the
in Table 6-1-5. The Automatic Adjustment Program executes the
2
1
Table 6-1-5
adjustment items if the LCD/EVF Adjustment Start button is
clicked.
clicked.
Block
Page
Address
V-COM Adj.
10
60
1052
Transmissive Mode White Balance Adj.
10
60
1056, 1057
VCO Adj.
10
60
103F (NTSC model),
1040 (PAL model)
1040 (PAL model)
Contrast Adj.
10
60
1047
White Balance Adj.
10
60
1045, 1046
Touch Panel
Adjustment
Adjustment
Touch Panel Adj.
Adjusting Address
Note:
The adjustment data cannot be read or written from the SeusEX.
(Note)
Button Name
Adjustment
EVF
Adjustment
Adjustment
LCD
Adjustment
Adjustment
6-34
HDR-SR11/SR11E/SR12/SR12E_ADJ
4) If the [End] button is clicked, the following screen is displayed
during the execution of “3. Transmissive Mode White Balance
Adj.”. Check that the LCD screen is not colored. If colored,
using the [Up]/[Down] button on the screen, adjust so that the
LCD screen is not colored. After the adjustment, click the [End]
button in the screen.
Adj.”. Check that the LCD screen is not colored. If colored,
using the [Up]/[Down] button on the screen, adjust so that the
LCD screen is not colored. After the adjustment, click the [End]
button in the screen.
5) If the [End] button is clicked, “4. Release of Data Setting dur-
ing LCD/EVF Adj.” will be executed.
6) Upon successful completion of all item the LCD Adjustment,
the following message is displayed. Click the [OK] button.
3.
LCD Adjustment
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during LCD/EVF Adj.
2. V-COM Adj.
3. Transmissive Mode White Balance Adj.
4. Release of Data Setting during LCD/EVF Adj.
sequence]
1. Data Setting during LCD/EVF Adj.
2. V-COM Adj.
3. Transmissive Mode White Balance Adj.
4. Release of Data Setting during LCD/EVF Adj.
[Adjusting method]
1) Click the [Start] button of the LCD Adjustment.
2) The Automatic Adjustment Program executes the “1. Data
1) Click the [Start] button of the LCD Adjustment.
2) The Automatic Adjustment Program executes the “1. Data
Setting during LCD/EVF Adj.”.
3) After that, the following screen is displayed during the execu-
tion of “2. V-COM Adj.”. Using the [Up]/[Down] button on the
screen, adjust so that the brightness of portions A and B on the
LCD panel is equal. After the adjustment, click the [End] but-
ton in the screen.
screen, adjust so that the brightness of portions A and B on the
LCD panel is equal. After the adjustment, click the [End] but-
ton in the screen.
6-35
HDR-SR11/SR11E/SR12/SR12E_ADJ
5.
Touch Panel Adjustment
[Automatic Adjustment Program execution items and
sequence]
1. Touch Panel Adj.
2. Release of Data Setting during LCD/EVF Adj.
sequence]
1. Touch Panel Adj.
2. Release of Data Setting during LCD/EVF Adj.
[Adjusting method]
1) Click the [Start] button of the Touch Panel Adjustment.
2) The Automatic Adjustment Program executes the “1. Touch
1) Click the [Start] button of the Touch Panel Adjustment.
2) The Automatic Adjustment Program executes the “1. Touch
Panel Adj.”. The following message is displayed, and then
adjust the LCD screen in accordance with the instructions given
on the screen. After the adjustment, click the [OK] button in
the message window.
adjust the LCD screen in accordance with the instructions given
on the screen. After the adjustment, click the [OK] button in
the message window.
3) If the [OK] button is clicked, “2. Release of Data Setting dur-
ing LCD/EVF Adj.” will be executed.
4) Upon successful completion of all item the Touch Panel Ad-
justment, the following message is displayed. Click the [OK]
button.
button.
4.
EVF Adjustment
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during LCD/EVF Adj.
2. EVF Automatic Adj.
sequence]
1. Data Setting during LCD/EVF Adj.
2. EVF Automatic Adj.
(VCO Adj., Contrast Adj.)
3. White Balance Adj.
4. Release of Data Setting during LCD/EVF Adj.
4. Release of Data Setting during LCD/EVF Adj.
[Adjusting method]
1) Click the [Start] button of the EVF Adjustment.
2) The Automatic Adjustment Program executes the “1. Data
1) Click the [Start] button of the EVF Adjustment.
2) The Automatic Adjustment Program executes the “1. Data
Setting during LCD/EVF Adj.” and “2. EVF Automatic Adj.”.
3) After that, the following screen is displayed during the execu-
tion of “3. White Balance Adj.”. Check that the EVF screen is
not colored. If colored, using the [Up]/[Down] button on the
screen, adjust so that the EVF screen is not colored. After the
adjustment, click the [End] button in the screen.
not colored. If colored, using the [Up]/[Down] button on the
screen, adjust so that the EVF screen is not colored. After the
adjustment, click the [End] button in the screen.
4) If the [End] button is clicked,“4.Release of Data Setting dur-
ing LCD/EVF Adj.” will be executed.
5) Upon successful completion of all item the EVF Adjustment,
the following message is displayed. Click the [OK] button.
Click on the first or last page to see other HDR-SR11 / HDR-SR11E / HDR-SR12 / HDR-SR12E (serv.man3) service manuals if exist.