DOWNLOAD Sony HDR-SR11 / HDR-SR11E / HDR-SR12 / HDR-SR12E (serv.man3) Service Manual ↓ Size: 760.69 KB | Pages: 48 in PDF or view online for FREE

6-16

HDR-SR11/SR11E/SR12/SR12E_ADJ

Check the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color
will become inconsistent.

Subject

Not required

Measurement Point

Pin 4 of IC1303 on VC-516 board

Measuring Instrument

Frequency counter

Specified value

f = 48000000 

± 960 Hz

Switch setting
1) POWER ............................................................. MOVIE mode

Checking method:
1) Check that the frequency (f) satisfies the specified value.

IC1301

IC1303 4pin

VC-516 BOARD (SIDE A)

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Video Adj.
2. S VIDEO OUT Y Level Adj.
3. S VIDEO OUT Chroma Level Adj.
4. VIDEO OUT Level Check
5. Release of Data Setting during Video Adj.

[Adjusting method]
1) Click the [Start] button of the S VIDEO OUT and VIDEO OUT

Adjustment.

2) The Automatic Adjustment Program executes the “1. Data

Setting during Video Adj.”.

3) If “1. Data Setting during Video Adj.” completed successfully,

the following screen is displayed during the execution of “2. S
VIDEO OUT Y Level Adj.”. Using the [Up] / [Down] button on
the screen, adjust so that the Y signal level satisfies the speci-
fied value. After the adjustment, click the [End] button in the
screen.

6-17

HDR-SR11/SR11E/SR12/SR12E_ADJ

4) After that, the following screen is displayed during the execu-

tion of “3. S VIDEO OUT Chroma Level Adj.”. Using the [Up]/
[Down] button on the screen, adjust so that the Cr signal level
and the Cb signal level satisfies the specified value. After the
adjustment, check that the burst level of the chroma signals
satisfies the specified value, and click the [End] button in the
screen.

5) If the [End] button is clicked, “4. VIDEO OUT Level Check”

will be executed. The following message and screen are dis-
played. Check that the sync signal level and burst level of the
video signals satisfies the specified value, and click the [OK]
button in the message.

6) If the [OK] button is clicked, “5. Release of Data Setting dur-

ing Video Adj.” will be executed.

7) Upon successful completion of all item the S VIDEO OUT

and VIDEO OUT Adjustment, the following message is dis-
played. Click the [OK] button.

6-18

HDR-SR11/SR11E/SR12/SR12E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Video Adj.
2. COMPONENT OUT Y Level Adj.
3. COMPONENT OUT Pb Level Adj.
4. COMPONENT OUT Pr Level Adj.
5. Release of Data Setting during Video Adj.

[Adjusting method]
1) Click the [Start]  button of the COMPONENT OUT Adjust-

ment.

2) The Automatic Adjustment Program executes the “1. Data

Setting during Video Adj.”.

3) If “1. Data Setting during Video Adj.” completed successfully,

the following screen is displayed during the execution of “2.
COMPONENT OUT Y Level Adj.”. Using the [Up]/[Down]
button on the screen, adjust so that the Y signal level satisfies
the specified value. After the adjustment, check that the sync
level of the Y signals satisfies the specified value, and click
the [End] button in the screen.

4) After that, the following screen is displayed during the execu-

tion of “3. COMPONENT OUT Pb Level Adj.”. Using the [Up]/
[Down] button on the screen, adjust so that the Pb signal level
satisfies the specified value. After the adjustment, check that
the sync level of the Pb signals satisfies the specified value,
and click the [End] button in the screen.

5) After that, the following screen is displayed during the execu-

tion of “4. COMPONENT OUT Pr Level Adj.”. Using the [Up]/
[Down] button on the screen, adjust so that the Pr signal level
satisfies the specified value. After the adjustment, check that
the sync level of the Pr signals satisfies the specified value,
and click the [End] button in the screen.

6-19

HDR-SR11/SR11E/SR12/SR12E_ADJ

6) If the [End] button is clicked, “5. Release of Data Setting dur-

ing Video Adj.” will be executed.

7) Upon successful completion of all item the COMPONENT

OUT Adjustment, the following message is displayed. Click
the [OK] button.