Sony HDR-FX1000 / HDR-FX1000E (serv.man3) Service Manual ▷ View online
6-72
HDR-FX1000/FX1000E_ADJ
2-2. EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in C
page, addresses F4, F8 and FC . The type of error indicated by the
code are shown in the following table.
page, addresses F4, F8 and FC . The type of error indicated by the
code are shown in the following table.
Code
Emergency Type
00
No error
10
Loading motor emergency during loading
11
Loading motor emergency during unloading
22
T reel emergency during normal rotation
23
S reel emergency during normal rotation
24
T reel emergency (Short circuit between S reel
terminal and T reel terminal)
terminal and T reel terminal)
30
FG emergency at the start up of the capstan
40
FG emergency at the start up of the drum
42
FG emergency during normal rotation of the drum
0010=2
0111=7
←
UNLOAD
Lock released
Cassette compartment
Cassette compartment
Pinch roller pressing
LS chassis movement section
EJ
BL
0011=3
0111=7
ULE
BL
0001=1
0111=7
LD1 (SR)
LD2 (HL)
BL
0101=5
0111=7
BL
0100=4
0111=7
STOP
BL
0110=6
R/P
LOAD
→
←
D (MSB)
←
C
←
B
←
A (LSB)
Mechanical Position
Position
EJ
BL
ULE
LD1 (SR)
LD2 (HL)
STOP
R/P
NULL
Code
2
7
3
1
5
4
6
0
F
Contents
Position at which the cassette component lock is released, at the farthest unload side mechanically
at which the mechanism can move no further in the UNLOAD direction.
at which the mechanism can move no further in the UNLOAD direction.
BLANK code, at the boundary between codes.
EJECT completion position. when the cassette is ejected, the mechanism will stop at this position.
Cassette IN standby. The guide will start protruding out as the mechanism moves towards the
LOAD position.
Cassette IN standby. The guide will start protruding out as the mechanism moves towards the
LOAD position.
When prepraing TOP load processing or when DEW is detected, rolling up tape by T reel is
preformed at this position.
preformed at this position.
When prepraing TOP load processing or when DEW is detected, rolling up tape by S reel is
preformed at this position.
preformed at this position.
Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the
brake is imposed on both reels.
brake is imposed on both reels.
PB, REC, CUE, REVIEW, PAUSE, FF, REW positions. When pinch roller is pressed, and the
tension regulator is ON, the mechanism is operating at this position in modes in which normal
images are shown.
tension regulator is ON, the mechanism is operating at this position in modes in which normal
images are shown.
Code not existing in the MD. Default value.
Status before finding any mechanism position.
2-3. MSW Code
MSW when errors occur:
Information on MSW (mode SW) when errors occur
MSW when movement starts:
Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved)
MSW of target of movement:
Information on target MSW of movement when the mechanism position is moved
Information on MSW (mode SW) when errors occur
MSW when movement starts:
Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved)
MSW of target of movement:
Information on target MSW of movement when the mechanism position is moved
6-73
HDR-FX1000/FX1000E_ADJ
3.
Bit Value Discrimination
Bit values must be discriminated using the display data of the ad-
justment remote commander for the following items. Us the table
below to discriminate if the bit value is “1” or “0”.
justment remote commander for the following items. Us the table
below to discriminate if the bit value is “1” or “0”.
(Example) If the remote commander display is “8E”, bit value from
bit 7 to bit 4 can be discriminated from the column
A
,
and those from bit 3 to bit 0 from column
B
.
Page
Address
bit3 to bit0 discrimination
bit7 to bit4 discrimination
Display on the adjustment remote commander
Display on the
adjustment
remote
commander
0
1
2
3
4
5
6
7
8
9
A (
A
)
B (
b
)
C (
C
)
D (
d
)
E (
E
)
F (
F
)
Bit values
bit3
or
bit7
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
bit2
or
bit6
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
bit1
or
bit5
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
bit0
or
bit4
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
A
B
4.
Jack Check (1)
Page 7
Address FF
Using method:
1) Select page: 7, address: FF.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
1) Select page: 7, address: FF.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
5.
Jack Check (2)
Page 7
Address 50
Using method:
1) Select page: 7, address: 50.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
1) Select page: 7, address: 50.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
Bit
Function
When bit value = 1
When bit value = 0
2
A/V R connector (JK-376 board CN9508)
Used (Component A/V)
Not used
3
A/V R connector (JK-376 board CN9508)
Used (Composite A/V multi)
Not used
Bit
Function
When bit value = 1
When bit value = 0
2
EXT MIC jack (MJ-002 board J9001)
ON
OFF
6-74
HDR-FX1000/FX1000E_ADJ
6.
Jack Check (3)
Page 3
Address CF
Bit
Function
When bit value = 1
When bit value = 0
0
HDMI OUT jack (FP-965 flexible CN001)
Used
Not used
Using method:
1) Select page: 3, address: CF.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
1) Select page: 3, address: CF.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
7.
Switch Check (1)
Page 2
Address EC
Using method:
1) Select page: 2, address: EC.
2) By discriminating the bit value of display data, the state of switch can be discriminated.
1) Select page: 2, address: EC.
2) By discriminating the bit value of display data, the state of switch can be discriminated.
8.
Switch Check (2)
Page 7
Address 4D
Using method:
1) Select page: 7, address: 4D.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
1) Select page: 7, address: 4D.
2) By discriminating the bit value of display data, the state of jack can be discriminated.
Bit
Function
When bit value = 1
When bit value = 0
0
POWER-VCR (Control switch block (PS24000))
ON
OFF
1
POWER-CAMERA (Control switch block (PS24000))
ON
OFF
2
EJECT (FP-969 flexible board S101)
ON
OFF
3
4
DISPLAY/BATT INFO (KY-105 board S7206)
ON
OFF
Bit
Function
When bit value = 1
When bit value = 0
7
AUDIO LEVEL AUTO/MANUAL
AUTO
MANUAL
(Control switch block (AU24000) S005)
6-75
HDR-FX1000/FX1000E_ADJ
9.
Switch Check (3)
Page 7
Address 63 to 6B
Note:
Check that the data of page: 0, address: 10 is “00”.
Using method:
1) Select page: 7, address: 63 to 6B.
2) By discriminating the display data, the pressed key can be discriminated.
1) Select page: 7, address: 63 to 6B.
2) By discriminating the display data, the pressed key can be discriminated.
MEMORY (VCR)
PLAY
(KY-105)
(S7202)
MEMORY (VCR)
INDEX
(KY-105)
(S7205)
MEMORY (VCR)
DELETE
(KY-105)
(KY-105)
(S7210)
VOLUME/
MEMORY
+
(KY-105)
(S7203)
VOLUME/
MEMORY
–
(KY-105)
(S7208)
DATA CODE
(KY-105)
(S7212)
ASSGIN
4
(AS-060)
(S8801)
ASSGIN
5
(AS-060)
(S8802)
ASSGIN
6
(AS-060)
(S8803)
ZERO SET
MEM
(KY-105)
(S7215)
PAUSE
(KY-105)
(S7213)
PANEL
REVERSE
(FP-966 FLEXIBLE)
(IC402)
(HT-002)
(S7401)
PANEL
CLOSE
CLOSE
(FP-966 FLEXIBLE)
(IC403)
PANEL
OPEN
(FP-966 FLEXIBLE)
(IC403)
PANEL
NORMAL
(FP-966 FLEXIBLE)
(IC402)
(HT-002)
(S7401)
STOP
(KY-105)
(S7201)
REW
(KY-105)
(S7204)
REC
(KY-105)
(S7209, S7211)
FF
(KY-105)
(S7216)
PLAY
(KY-105)
(S7214)
SLOW
(KY-105)
(S7217)
–
–
–
–
–
–
–
–
–
65
(KEY AD0)
(VC-543)
(IC3601 )
C5
Address
00
1B
36
53
A0
CF
FF
77
00 to 0C
0D to 26
27 to 43
44 to 63
8B toB6
B7 to E6
E7 to FF
64 to 8A
Data
66
(KEY AD1)
(VC-543)
(IC3601 )
B3
67
(KEY AD2)
(VC-543)
(IC3601 )
B4
68
(KEY AD3)
(VC-543)
(IC3601 )
D2
69
(KEY AD4)
(VC-543)
(IC3601 )
E2
6A
(KEY AD5)
(VC-543)
(IC3601 )
E1
6B
(KEY AD6)
(VC-543)
(IC3601 )
C2
63
(KEY AD7)
(VC-543)
(IC3601 )
B5
64
(KEY AD8)
(VC-543)
(IC3601 )
A3
( )
REC
START/STOP
CONTROL
SWITCH BLOCK
(PS24000)
(S301)
( )
REC
START/STOP
CONTROL
SWITCH BLOCK
(GZ92000)
(S001)
( )
PHOTO/
EXPANDED
FOCUS
CONTROL
SWITCH BLOCK
(PZ24000)
(S501)
( )
PICTURE
PROFILE
CONTROL
SWITCH BLOCK
(KP24000)
(S302)
( )
STATUS
CHECK
CONTROL
SWITCH BLOCK
(KP24000)
(S303)
( )
IRIS/
EXPOSURE
CONTROL
SWITCH BLOCK
(CF24000)
(S204)
( )
WHT BAL
CONTROL
SWITCH BLOCK
(CF24000)
(S202)
( )
MENU
CONTROL
SWITCH BLOCK
(KP24000)
(S301)
( )
SHUTTER
SPEED
CONTROL
SWITCH BLOCK
(CF24000)
(S203)
( )
SEL/PUSH
EXEC
CONTROL
SWITCH BLOCK
(KP24000)
(S304)
( )
AUTO LOCK:
AUTO
CONTROL
SWITCH BLOCK
(CF24000)
(S208)
( )
ASSIGN 1
ZEBRA
CONTROL
SWITCH BLOCK
(AU24000)
(S001)
( )
ASSIGN 2
AE SHIFT
AE SHIFT
CONTROL
SWITCH BLOCK
(AU24000)
(S002)
( )
ASSIGN 3
REC REVIEW
CONTROL
SWITCH BLOCK
(AU24000)
(S003)
( )
FOCUS
PUSH AUTO
CONTROL
SWITCH BLOCK
(AU24000)
(S004)
( )
FOCUS
AUTO
CONTROL
SWITCH BLOCK
(AU24000)
(S009)
( )
FOCUS
INFINITY
CONTROL
SWITCH BLOCK
(AU24000)
(S009)
( )
FOCUS
MAN
CONTROL
SWITCH BLOCK
(AU24000)
(S009)
( )
AUTO LOCK:
MANUAL
CONTROL
SWITCH BLOCK
(CF24000)
(S208)
( )
GAIN
H
CONTROL
SWITCH BLOCK
(CF24000)
(S205)
( )
GAIN
L
CONTROL
SWITCH BLOCK
(CF24000)
(S205)
( )
GAIN
M
CONTROL
SWITCH BLOCK
(CF24000)
(S205)
( )
WHT BAL
PRS
CONTROL
SWITCH BLOCK
(CF24000)
(S206)
( )
WHT BAL
B
CONTROL
SWITCH BLOCK
(CF24000)
(S206)
( )
WHT BAL
A
CONTROL
SWITCH BLOCK
(CF24000)
(S206)
( )
GAIN
CONTROL
SWITCH BLOCK
(CF24000)
(S201)
( )
CONTROL
SWITCH BLOCK
(CF24000)
(S207)
(WHT BAL ONE PUSH)
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Click on the first or last page to see other HDR-FX1000 / HDR-FX1000E (serv.man3) service manuals if exist.