DOWNLOAD Sony DCR-TRV345E / DCR-TRV350 / DCR-TRV351 / DCR-TRV355E / DCR-TRV356E (serv.man4) Service Manual ↓ Size: 1.02 MB | Pages: 73 in PDF or view online for FREE

6-50

Set the CAP FG signal duty cycle to 50% to establish an appropri-
ate capstan servo. If deviated, the uneven rotation of capstan and
noise can occur in the LP mode.

Mode

VTR playback

Signal

Hi8/Standard8 alignment tape:
 For checking operation
 (WR5-5NSP (NTSC))
 (WR5-5CSP (PAL)

Measurement Point

Displayed data of

CAP FG (Pin 4

page: 3, address: 03  of CN1011)

Measuring Instrument

Adjusting remote

Oscilloscope

commander

Adjustment Page

C

Adjustment Address

16

Specified value

The data of page: 3, Duty = 50 

± 1 %

address: 03 is “00”

Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

Insert the alignment tape and
enter the VTR playback mode.

2

0

01

01

3

3

01

81

Press PAUSE button.

4

3

02

Check the data changes to
“00”.

5

3

03

Check the data is “00”. (Note 2)

6

Check that Duty of CAP FG
signal satisfies the specified
value.

7

0

01

00

If the data is other value, adjustment has errors.
For the error contents, see the following table.

Bit value of page: 3,

Error contents

address: 03

bit0 = 1

Adjustment time out

bit1 = 1

No changed to Hi8/Standard8 mode

Before perform the servo and RF system adjustments, check that
the specified values of “27/36MHz Origin Oscillation Adjustment”
of “VIDEO SYSTEM ADJUSTMENTS” is satisfied.
Check that the data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.

Adjusting Procedure:
1. REEL FG adjustment
2. CAP FG duty adjustment
3. Digital8 switching position adjustment
4. SD error rate check
5. Hi8/Standard8 switching position adjustment

Compensates the dispersion of the hall elements.

Mode

VTR stop

Signal

No signal

Measurement Point

Displayed data of page: 3, address:
03

Measuring Instrument

Adjusting remote commander

Adjustment Page

C

Adjustment Address

17, 2F

Specified value

The data of page: 3, address: 03 is
“00” or “01” or “04” or “05”

Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

Close the cassette compart-
ment without inserting cas-
sette.

2

0

01

01

3

3

01

1C

Press PAUSE button.

4

3

02

Check the data changes to
“00”.

5

3

03

Check the data is “00” or “01”
or “04” or “05”. (Note 2)

6

0

01

00

If the data is other value, adjustment has errors.
For the error contents, see the following table.

Data

Error contents

02, 03, 06, 07

T REEL is defective

08, 09, 0C, 0D

S REEL is defective

0A, 0B, 0E, 0F

T REEL and S REEL is defective

A

B

Duty = A/B 

×

 100 [%] 

Center of movement 

6-51

Checking the video error rate in LP mode, adjust the filter tap
coefficient of IC6001.

Mode

VTR playback

Signal

Recorded signal at “Preparations
before adjustments”

Measurement Point

Displayed data of page: 3, address:
03

Measuring Instrument

Adjusting remote commander

Adjustment Page

1C (Note 1)

Adjustment Address

B3 to C8

Specified value

The data of page: 3, address: 03 is
“00”

If reading/writing data on page 1C, set data: 01 to page:
0, address: 10, and then select page C. By this data set-
ting, the page C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.

Switch setting:
1) REC MODE (Menu display) .............................................. LP

Preparations before adjustment:
1) Set the camcoder to CAMERA mode (LP mode).
2) Record camera signal for a minute, and rewind tape.

Order Page Address Data

Procedure

1

0

01

01

2

7

62

Set the bit value of bit0 is “1”.
(Note 2)

3

Playback the recorded signal
at“Preparations before adjust-
ments”.

4

3

01

40

Press PAUSE button.

5

3

02

Check the data changes to
“00”.

6

3

03

Check the data is “00”. (Note 3)

7

7

62

Set the bit value of bit0 is “0”.
(Note 2)

8

0

01

00

For the bit value, refer to “6-4. SERVICE MODE”, “4-3.
3. Bit Value Discrimination”.

If the data is other value, adjustment has errors.
For the error contents, see the following table.

Data

Error contents

01

Error rate of the EVEN channel exceeds the specified
value

02

Error rate of the ODD channel exceeds the specified
value

03

Error rate of the EVEN and ODD channels exceeds the
specified value

To obtain normal playback waveform output, adjust the switching
position.

Mode

VTR playback

Signal

Digital8 alignment tape:
SW/OL standard (WR5-2D)

Measurement Point

Displayed data of page: 3, address:
03

Measuring Instrument

Adjusting remote commander

Adjustment Page

C

Adjustment Address

10, 11, 12, 13

Specified value

The data of page: 3, address: 03 is
“00”

Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

Insert the SW/OL standard tape
and enter the VTR stop mode.

2

0

01

01

3

C

10

EE

Press PAUSE button.

4

3

21

Check the data is “02”. (Note 2)

5

3

01

0D

Press PAUSE button.

6

3

02

Check the data changes to
“00”.

7

3

03

Check the data is “00”.
(Note 3, 4)

8

0

01

00

If the data is “72”, the tape top being played. After play-
ing the tape for 1 to 2 seconds, stop it, perform step 5 and
higher.
If the data is “62”, the tape end being played. After re-
wind the tape, perform step 5 and higher.

If the data is not “00”, select page: C, address: 21 and
take a note of the data. Set data: 10, press the PAUSE
button, then perform the adjustment again.
When the data does not become “00” even if the adjust-
ment has been performed again, set back the data on page:
C, address: 21.

If bit0 of the data is “1”, the EVEN channel is defective.
If bit1 of the data is “1”, the ODD channel is defective.
Contents of the defect is see written into page: C, ad-
dress: 10 and 12. See following table.
(For the bit values, refer to “6-4. SERVICE MODE”, “4-
3. 3. Bit Value Discrimination”.)
If bit3 of the data is “1”, the tape end being played. After
rewinding the tape, perform the adjustment again.

When the EVEN channel is defective

Data of page: C,

Contents of defect

address: 10

EE

Writing into EEP ROM (IC4502) is defective

E8

Adjustment data is out of range

E7

No data is returned from IC6001

When the ODD channel is defective

Data of page: C,

Contents of defect

address: 12

E8

Adjustment data is out of range

E7

No data is returned from IC6001

6-52

If deviated in this case cause switching noise or jitter on the Hi8/
Standard8 mode played back screen.

Mode

VTR playback

Signal

Hi8/Standard8 alignment tape:
 For tracking adjustment
 (WR5-1NP (NTSC))
 (WR5-1CP (PAL))

Measurement Point

CH1: SWP (Pin 5 of CN1011)
CH2: IR VIDEO (Pin 2 of CN1011)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

70, 71

Specified value

t1 = 0 

± 10 µsec

Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

Insert the alignment tape and
enter the VTR stop mode.

2

0

01

01

3

0

10

01

4

8

12

Set the bit value of bit6 is “1”.
(Note 2)

5

0

10

00

6

7

62

Set the bit value of bit1 is “1”.
(Note 2)

7

Set to the playback mode.

8

C

70

Change the data and minimize
“t1”. (Coarse adjustment)

9

C

70

Press PAUSE button.

10

C

71

Change the data and adjust so
that the switching position (t1)
becomes specified value. (Fine
adjustment)

11

C

71

Press PAUSE button.

12

7

62

Set the bit value of bit1 is “0”.
(Note 2)

13

0

10

01

14

8

12

Set the bit value of bit6 is “0”.
(Note 2)

15

0

10

00

16

0

01

00

For the bit value, refer to “6-4. SERVICE MODE”, “4-3.
3. Bit Value Discrimination”.

CH1

CH2

Enlargement

t1=0 

±

 10 

µ

sec

CH1

CH2

6-53

Before performing the video system adjustments, check that the
data of page: 0, address: 10 is “00”.
If not, select  page: 0, address: 10, and set data “00”.
Video system adjustments must be performed in the following or-
der.

Adjusting Procedure:
1. 27/36 MHz origin oscillation adjustment
2. S VIDEO OUT Y level adjustment
3. S VIDEO OUT C level adjustment
4. VIDEO OUT level check
5. Hi8/Standard8 Y/C output level setting
6. Hi8/Standard8 AFC f

0

 adjustment

Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color
will become inconsistent.

Mode

CAMERA

Subject

Arbitrary

Measurement Point

Pin <z.,  of IC2201

Measuring Instrument

Frequency counter

Adjustment Page

F

Adjustment Address

10

Specified value

f = 13500000 

± 68 Hz (NTSC model)

f = 18000000 

± 90 Hz (PAL model)

Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

0

01

01

2

F

10

Change the data and set the
frequency (f) to the specified
value.

3

F

10

Press PAUSE button.

4

0

01

00

Mode

CAMERA

Subject

Arbitrary

Measurement Point

Y signal terminal of
S VIDEO jack (75 

Ω terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

C

Adjustment Address

25

Specified value

A = 1000 

± 20 mVp-p

Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

0

01

01

2

8

A0

Set the bit value of bit 3 to “1”,
and press PAUSE button.
(Note 2)

3

3

0C

02

Press PAUSE button.

4

C

25

Change the data and set the Y
signal level (A) to the
specified value.

5

C

25

Press PAUSE button.

6

8

A0

Set the bit value of bit 3 to “0”,
and press PAUSE button.
(Note 2)

7

3

0C

00

Press PAUSE button.

8

0

01

00

For the bit values, refer to  “6-4. SERVICE MODE”, “4-
3. 3. Bit Value Discrimination”.

H

Center of luminance line

A

1

54

55

108

109

162

163

198

216

IC2201