DOWNLOAD Sony DCR-TRV345E / DCR-TRV350 / DCR-TRV351 / DCR-TRV355E / DCR-TRV356E (serv.man4) Service Manual ↓ Size: 1.02 MB | Pages: 73 in PDF or view online for FREE

6-30

Order Page Address Data

Procedure

1

6

48

00

2

0

03

00

3

Remove the ND filter 1.5
(1.0 + 0.4 + 0.1) on the lens.

Mode

CAMERA

Subject

Clear chart
(Color reproduction adjustment
frame)

Filter

Filter C14 for color temperature
correction
ND filter 1.0, 0.4 and 0.1

Measurement Point

Video terminal of

Displayed data of

A/V jack

page: 1 (Note 3)

(75 

Ω terminated)

Measuring Instrument

Vectorscope

Adjusting remote
commander

Specified Value

Fig. 6-1-12

LV data:

(A) and (B)

8000 to 8BC0

Check that the data of page: 0, address: 10 is “00”.

Perform “Auto White Balance Adjustment” before this
adjustment.

The right four digits of the page: 1 displayed data of the
adjusting remote commander.

                    1:XX:XX

Displayed data

Switch setting:
1) NIGHT SHOT .................................................................. OFF
2) DIGITAL ZOOM (Menu setting) .................................... OFF
3) STEADY SHOT (Menu setting) ..................................... OFF

Order Page Address Data

Procedure

1

Check that the lens is not
covered with either filter.

2

6

48

01

  INDOOR luminance point check

3

6

01

0F

Press PAUSE button.

4

Check that the center of the
white luminance point within
the circle shown Fig. 6-1-12
(A).

5

6

01

00

Press PAUSE button.

  OUTDOOR luminance point check

6

6

01

3F

Press PAUSE button.

7

Place the C14 filter on the
lens.

8

Check that the center of the
white luminance point within
the circle shown Fig. 6-1-12
(B).

  LV data check

9

Remove the C14 filter, and
place the ND filter 1.5 (1.0 +
0.4 + 0.1) on the lens.

10

6

01

00

Press PAUSE button.

11

0

03

06

12

1

Check that the displayed data
(Note 3) satisfied the LV data
specified value.

R-Y

2 mm

B-Y

2 mm

R-Y

B-Y

0.5 mm

1 mm

3 mm

3 mm

6-31

Check the angular velocity sensor output.

Precautions on the Parts Replacement
There are two types of repair parts.

Type A

ENC03JA

Type B

ENC03JB

Replace the broken sensor with a same type sensor. If replace with
other type parts, the image will vibrate up and down or left and
right during hand-shake correction operations.

Precautions on Angular Velocity Sensor
The sensor incorporates a precision oscillator. Handle it with care
as if it dropped, the balance of the oscillator will be disrupted and
operations will not be performed properly.

Mode

CAMERA

Subject

Not required

Measurement Point

Displayed data of page: 1 (Note 2)

Measuring Instrument

Adjusting remote commander

Specified value

PITCH data: 2B00 to 4B00
YAW data: 2B00 to 4B00

Check that the data of page: 0, address: 10 is “00”.

The right four digits of the page: 1 displayed data of the
adjusting remote commander.

1:XX:XX

Displayed data

Switch setting:
1) ZOOM ..................................................................... TELE end
2) STEADYSHOT (Menu setting) ........................................ ON

Order Page Address Data

Procedure

  PITCH sensor output check (SE751 of SI-036 board)

1

0

03

11

2

1

With the set in still state,
check that the displayed data
(Note 2) satisfies the PITCH
data specified value.

  YAW sensor output check (SE752 of SI-036 board)

3

0

03

12

4

1

With the set in still state,
check that the displayed data
(Note 2) satisfies the YAW
data specified value.

5

0

03

00

  Steady shot operation check

6

Shake the set vertically and
horizontally to check that the
steady shot function operates
normally.

6-32

Before perform the viewfinder system adjustments, check that the
data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.

Taken an extreme care not to destroy the liquid crystal

display module by static electricity when replacing it.

Perform the following data setting before the viewfinder
system adjustments.
1) Select page: 3, address: C4, and set data: 67.
2) Select page: 3, address: C5, and set data: 01.
Reset the data after completing adjustment.
1) Select page: 3, address: C4, and set data: 00.
2) Select page: 3, address: C5, and set data: 00.

Most of the measuring points for adjusting the viewfinder system
are concentrated in CN1011 of the VC-305 board.
Connect the measuring instruments via I/F unit for LANC control
(J-6082-521-A) and CPC jig connector (J-6082-539-A).

The following table shows the pin No. and signal name of CN1101.

Pin No.

Signal Name

Pin No.

Signal Name

1

FRRV

9

RF MON

2

8 mm PB RF

10

REG GND

3

BPF MONI

11

N.C.

4

CAP FG

12

N.C.

5

RF SWP

13

XLANC POWER ON

6

REG GND

14

EVF VG

7

XLANC JACK IN

15

VCO

8

REG GND

16

LANC SIG

The following table lists the test point of I/F unit of for LANC
control.

Pin No.

Signal Name

Pin No.

Signal Name

BL

15

EVF VCO

14

EVF VG

BL 4.75

9

PB RF (MON)

3

BPF MONI

6, 8, 10

GND

TMS

7

REC RF (RF IN)

TDI

TDO

5

SWP

TCK

4

CAP FG

2

IR VIDEO

 Pin No. are those of CN1011.

CN1011

16

1

Conductor 
side

6-33

Set the VCO free-run frequency. If deviated, the EVF screen will
be blurred.

Mode

CAMERA

Subject

Not required

Measurement Point

EVF VCO (Pin qg of CN1011)

Measuring Instrument

Frequency counter

Adjustment Page

C

Adjustment Address

36, 37

Specified Value

f = 15734 

± 30 Hz (NTSC model)

f = 15625 

± 30 Hz (PAL model)

Check that the data of page: 0, address: 10 is “00”.

NTSC model: DCR-TRV350/TRV351
PAL model: DCR-TRV345E/TRV355E/TRV356E

Order Page Address Data

Procedure

1

0

01

01

2

C

36

Change the data and set the
frequency (f) to the specified
value.

3

C

36

Press PAUSE button.

4

C

36

Read the data and this data is
named D

36

.

5

Convert D

36

 to decimal nota-

tion, and obtain D

36

’. (Note 3)

6

Calculate D

37

’ using following

equations. (decimal calcula-
tion)
D

37

’ = D

36

’ + 19 (NTSC model)

D

37

’ = D

36

’ – 19 (PAL model)

7

Convert D

37

’ to a hexadecimal

number, and obtain D

37

.

(Note 3, 4)

8

C

37

D

37

Press PAUSE button.

9

0

01

00

Refer to table 6-4-1. “Hexadecimal-decimal conversion
table”

If D

37

’ > 255, then D

37

 = FF (NTSC model)

If D

37

’ < 0, then D

37

 = 00 (PAL model)