DOWNLOAD Sony DCR-PC330 / DCR-PC330E (serv.man4) Service Manual ↓ Size: 1.47 MB | Pages: 74 in PDF or view online for FREE

6-6

Fig. 6-1-3.

CPC lid

Adjustment remote
commander (RM-95)

AC power
adaptor 

AC IN

LANC jack

LANC jack

For tape path adjustment

DC IN connector

CPC-6 terminal board jig
(J-6082-371-A)

CPC-6 flexible jig
(J-6082-370-C)

Screw 
(M1.7 

× 

2.5),

lock ace, p2

6-7

1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.

1.

POWER switch (PS5000 block) ............................ CAMERA

2.

NIGHT SHOT switch (FK5000 block) ............................ OFF

3.

BACK LIGHT switch (FK5000 board) ........................... OFF

4.

FOCUS switch (FK5000 block) ...................................... OFF

5.

Touch panel settings

CAMERA SET of the menu

PROGRAM AE .................................................... AUTO
SPOT METER ...................................................... AUTO
EXPOSURE ......................................................... AUTO

WHITE BALANCE ............................................. AUTO
COLOR SLOW SHUTTER ..................................... OFF
DIGITAL ZOOM ..................................................... OFF
16 : 9 WIDE .............................................................. OFF
STEADY SHOT ....................................................... OFF

APPLICATION of the menu

PICTURE EFFECT .................................................. OFF
DIGITAL EFFECT ................................................... OFF

2. Order of Adjustments
Basically carry out adjustments in the order given.

Fig. 6-1-4.

3. Subjects
1)

Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)

2)

Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)

3)

Flange back adjustment chart
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm 

×

841mm) black and white vellum paper.

Fig. a

(Video output terminal

output waveform)

Fig. b (TV monitor picture)

Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.

Fig. 6-1-5.

Note: Use matte vellum paper bigger than A0, and make sure the edges of

the black and white paper joined together are not rough.

6-8

4. Preparing the Flash Adjustment Box
A dark room is required to provide an accurate strobe adjustment.
If it is not available, prepare the flash adjustment box as given below;

1) Provide woody board A, B and C of 15 mm thickness.

woody board A (2 sheets)

400 mm

woody board B (2 sheets)

370 mm

woody board C (1 sheet)

700 mm

513 mm

513 mm

700 mm

700 mm

730 mm

2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side

of woody board A, B and C are internal. (Fig. 6-1-7)

Fig. 6-1-6

Fig. 6-1-7

6-9

Note: When reading or writing the 14, 18, 19, 1B, 1C, 1E or 1F page data,

select page: 0, address: 10, and set data: 01, then select 4, 8, 9, B, C,
E or F page. The 14, 18, 19, 1B, 1C, 1E or 1F page can be chosen by
this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.

 [Initialization Procedure]
1.

Initialization of A, D page data

2.

Initialization of B, 1B page data

3.

Initialization of 8, C, 18, 1C page data

4.

Initialization of E, F, 14, 19, 1E, 1F page data

Note: The data of page: 0, address: 10 must be “00”.

Note1: If “Initializing the A, D Page Data” is performed, all data of the A

page and D page will be initialized. (It is impossible to initialize a
single page.)

Note2: If the A, D page data has been initialized, the following adjustments

need to be performed again.
1) Modification of A, D page data
2) Touch panel adjustment

Note3: NTSC model: DCR-PC330

PAL model: DCR- PC330E

Adjusting page

A

Adjusting Address

10 to FF

Adjusting page

D

Adjusting Address

10 to 7F

1

0

01

01

Set the data.

2

0

10

00

Set the data.

3

7

03

Set the following data.
01 (NTSC), 81 (PAL)

4

7

00

Set the following data.
20 (Initializing A page)
22 (Initializing D page)
28 (Initializing A and D pages)

5

7

01

Set the following data, and press
PAUSE button.
20 (Initializing A page)
22 (Initializing D page)
28 (Initializing A and D pages)

6

7

02

Check that the data changes to “01”

7

Perform “Modification of A, D
Page Data”.

2. Modification of A, D Page Data
If the A, D page data has been initialized, change the data of the
“Fixed data-2” address shown in the following tables by manual
input.

Modifying Method:
1)

Before changing the data, select page: 0, address: 01, and set
data: 01.

2)

New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.

Note: If copy the data built in the different model, the camcorder may

not operate.

3)

When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.

1

2

00

29

Set the data.

2

2

01

29

Set the data, and press PAUSE
button.

Note: If the following symptoms occur after completing of the

“Modification of A, D page data”, check that the data of addresses:
1A to 4F of A page and the data of addresses: 12, 13 of D page are
same as those of the same model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
2) The power is shut off so that unit cannot operate.