Sony DCR-PC101 / DCR-PC101E (serv.man2) Service Manual ▷ View online
89
Editing
(2) Setting the modes to cancel the recording pause on the
VCR
1
Press
r/R to select PAUSEMODE, then press EXEC.
2
Press
r/R to select the mode to cancel recording pause on the VCR, then
press EXEC.
The correct button depends on your VCR.
Refer to the operating instructions of your VCR.
The correct button depends on your VCR.
Refer to the operating instructions of your VCR.
Buttons that cancel recording pause on the VCR
The buttons vary depending on your VCR. To cancel recording pause of your VCR:
– Select PAUSE if the button to cancel recording pause is X.
– Select REC if the button to cancel recording pause is z.
– Select PB if the button to cancel recording pause is N.
The buttons vary depending on your VCR. To cancel recording pause of your VCR:
– Select PAUSE if the button to cancel recording pause is X.
– Select REC if the button to cancel recording pause is z.
– Select PB if the button to cancel recording pause is N.
(3) Locate the infrared rays emitter of your camcorder and
face it towards the remote sensor of the VCR
Set the devices about 30 cm (12 in.) apart, and remove any obstacles between the
devices.
devices.
1
2
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
PAUSE
REC
PB
REC
PB
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
PAUSE
END
END
VCR
Remote sensor
Infrared rays emitter
A/V connecting cable (supplied)
Dubbing only desired scenes – Digital program editing (on tapes)
90
Dubbing only desired scenes – Digital program editing (on tapes)
2,3
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
ENGAGE
REC PAUSE
REC PAUSE
RETURN
EXECUTE
EXECUTE
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
COMPLETE
END
END
(4) Confirming the VCR operation
1
Insert a recordable tape into the VCR, then set the VCR to recording pause.
2
Press
r/R to select IR TEST, then press EXEC.
3
Press
r/R to select EXECUTE, then press EXEC.
If the VCR starts recording, the setting is correct.
The indicator you selected to cancel recording pause on the VCR flashes on
the LCD screen. When finished, the indicator changes to COMPLETE.
The indicator you selected to cancel recording pause on the VCR flashes on
the LCD screen. When finished, the indicator changes to COMPLETE.
When the VCR does not operate correctly
• After checking the code in “About the IR SETUP” code, set the IR SETUP or the
• After checking the code in “About the IR SETUP” code, set the IR SETUP or the
PAUSEMODE again.
• Place your camcorder at least 30 cm (12 in.) away from the VCR.
• Refer to the operating instructions of your VCR.
• Refer to the operating instructions of your VCR.
Step 2: Setting the VCR to operate with the i.LINK cable
When you connect using the i.LINK cable (optional), follow the procedures below.
(1) Set the POWER switch to VCR on your camcorder.
(2) Turn the power of the connected VCR on, then set the input selector to DV
(2) Turn the power of the connected VCR on, then set the input selector to DV
input.
When you connect a digital video camera recorder, set its power switch to
VCR/VTR.
When you connect a digital video camera recorder, set its power switch to
VCR/VTR.
(3) Press FN to display PAGE1.
(4) Press MENU, then select VIDEO EDIT in
(4) Press MENU, then select VIDEO EDIT in
, then press EXEC (p. 192).
(5) Press r/R to select TAPE, then press EXEC.
(6) Press EDIT SET.
(7) Press r/R to select CONTROL, then press EXEC.
(8) Press r/R to select i.LINK, then press EXEC.
(6) Press EDIT SET.
(7) Press r/R to select CONTROL, then press EXEC.
(8) Press r/R to select i.LINK, then press EXEC.
91
Editing
Dubbing only desired scenes – Digital program editing (on tapes)
4
5
6
7,8
3
FN
OTHERS
DATA CODE
BEEP
COMMANDER
D I SPL AY
V I DEO ED I T
BEEP
COMMANDER
D I SPL AY
V I DEO ED I T
READY
EXIT
RET.
EXEC
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
I R
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
I R
i. L I NK
i. L I NK
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
I R
i. L I NK
i. L I NK
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
i. L I NK
OTHERS
DATA CODE
BEEP
COMMANDER
D I SPL AY
V I DEO ED I T
BEEP
COMMANDER
D I SPL AY
V I DEO ED I T
EXIT
RET.
EXEC
RETURN
TAPE
MEMORY
TAPE
MEMORY
0:32:30:14
TOTAL
SCENE
SCENE
0:00:00:00
0
0
V I DEO ED I T
MARK
I N
I N
START
ED I T
SET
SET
UNDO
END
END
END
END
END
Note
When you connect with an i.LINK cable, you may not be able to operate the dubbing
function correctly, depending on the VCR.
Set CONTROL to IR in the menu settings of your camcorder.
When you connect with an i.LINK cable, you may not be able to operate the dubbing
function correctly, depending on the VCR.
Set CONTROL to IR in the menu settings of your camcorder.
When you connect using i.LINK cable
You cannot dub the titles, display indicators.
You cannot dub the titles, display indicators.
92
Dubbing only desired scenes – Digital program editing (on tapes)
Step 3: Adjusting the synchronization of the VCR
You can adjust the synchronization of your camcorder and the VCR.
Prepare a pen and paper for notes.
Before operation, eject a cassette from your camcorder (if inserted).
Prepare a pen and paper for notes.
Before operation, eject a cassette from your camcorder (if inserted).
(1) Insert a recordable tape into the VCR, then set the VCR to recording pause.
When you select i.LINK in CONTROL, the recording pause is not necessary.
(2) Press r/R to select ADJ TEST, then press EXEC.
(3) Press r/R to select EXECUTE, then press EXEC.
(3) Press r/R to select EXECUTE, then press EXEC.
IN and OUT are recorded on an image for five times each to calculate the
numerical values for adjusting the synchronization.
The EXECUTING indicator flashes on the LCD screen. When finished, the
indicator changes to COMPLETE.
numerical values for adjusting the synchronization.
The EXECUTING indicator flashes on the LCD screen. When finished, the
indicator changes to COMPLETE.
(4) Rewind the tape in the VCR, then start slow playback.
Take a note of the opening numerical value of each IN and the closing
numerical value of each OUT.
numerical value of each OUT.
(5) Calculate the average of five opening numerical values of five IN, and the
average of all the closing numerical values of each OUT.
(6) Press r/R to select “CUT-IN”, then press EXEC.
(7) Press r/R to select the average numerical value of IN, then press EXEC.
(7) Press r/R to select the average numerical value of IN, then press EXEC.
The calculated start position for recording is set.
(8) Press r/R to select “CUT-OUT”, then press EXEC.
(9) Press r/R to select the average numerical value of OUT, then press EXEC.
(9) Press r/R to select the average numerical value of OUT, then press EXEC.
The calculated stop position for recording is set.
(10) Press
RET. to execute.
Click on the first or last page to see other DCR-PC101 / DCR-PC101E (serv.man2) service manuals if exist.