DOWNLOAD Sharp 32KF-84H (serv.man5) Service Manual ↓ Size: 308.05 KB | Pages: 7 in PDF or view online for FREE

1. Stand-by button (TV)

2. Power button (VCR)

3. 0 ~ 9 digit buttons 
4. Flash back button

5. GREEN button
6. RED button

7. Volume DOWN button
8. MENU button

9. REVEAL button

10. LIST button
11. STORE button
12. CANCEL button
13. HALF PAGE button

14. RESET button

15. Rewind/picture search reverse
16. Play button
17. Pause/Still button
18. Stop button

19. TV/VIDEO button
20. Channel Call button
21. Single/Double entry button

22. YELLOW button
23. BLUE button

24. Channel UP button
25. Volume UP button
26. Channel DOWN button
27. Wide mode button

28. CLOCK button

29. Sound mode button

30. HOLD button

31. Sound Mute button

32. TEXT/MIX/PICTURE button
33. INDEX button

34. Channel UP button (VCR)
35. Fast forward/picture search forward
36. Channel DOWN button (VCR)
37. Record button

All adjustments to this chassis, except for focus, are carried out in the Service Mode.

The Service Mode is provided to enable the engineer to correctly set up the receiver to the CRT fitted in the set.
Note that these adjustments may vary from one receiver to another.

To enter the Service Mode, carry out the following procedure.
1. Connect a test pattern to the antenna terminal.
2. Tune the receiver to this signal.
3. Turn the receiver off using the mains switch.
4. Press volume down and channel up buttons on the
    front of the receiver at the same time.
5. Keeping these buttons pressed, turn the mains on.
6. When the set starts up it will be in Service Mode.
7. Release the two buttons.

8

1

01. Horizontal Shift
02.

 

East West Width

03.

 

Pin Phase

04. Pin Amp
05. Upper corner correction
06. Lower corner correction
07. Extreme Corner Correction
08. Vertical Linearity
09. Vertical Angle
10. Vertical Bow

11. Vertical Amplitude
12. S Correction
13. Vertical Shift
14. Red Cut Off
15. Green Cut Off
16. Blue Cut Off
17. Alter NVM Pag (Page)
18. Alter NVM Pos (Position)
19. Alter NVM Val (Value)
20. Teletext Mix Mode Contrast

21. Teletext Contrast
22. OSD Contrast
23. DVCO Adjustment (Only PAL)
24. DVCO Adjustment (Only NTSC)
25. AGC Adjustment
26. Auto Installation On/Off

•••••

 Use the channel up and down buttons to move between the options.

•••••

 Use the volume control buttons to change the data.

•••••

 To store the data, use the stand-by button on the remote control.

•••••

 To exit the Service Mode, turn the receiver off using the mains switch.

When the Service Mode is entered the following On Screen Display appears:

The figures displayed in the “XXXX” locations are hexadecimal representations of the number of times that particular
function has been executed. For example if the hexadecimal number displayed after “SW ON” was 0E4A, this would
correspond to the receiver being turned on 3658 times.

 

X

The following adjustments can be carried out in the Service Mode.

When in the Service Mode it is possible to access certain functions by using the teletext keys as below.

•••••

 By pressing the   Blue   button each adjustment can be directly accessed via the remote control. Referring to the

list above, press the   Blue  button followed by the adjustment number, this will directly access the selected
adjustment. If any number above 26 is selected, the set will revert to the Service Mode entry page. To access a
number less than 10, use the 0 key first, i.e. 02.

•••••

 Press the  Yellow  button to go straight to the AGC adjustment.

•••••

 Press the Green  button once to enter  “FACTORY VOLUME” level. Use volume control keys to change the

setting. The original value will be recovered after resetting the TV set.

•••••

 Press the Green  button twice to enter  “FACTORY BALANCE” level. Use volume control keys to change the

setting. The original value will be recovered after resetting the TV set.

•••••

 Press the   Red   button once to enter “FACTORY CONTRAST” level.  Use volume control keys to change the

setting. The adjustment is stored automatically.

•••••

 Press the    Red    button twice to enter “FACTORY BRIGHTNESS” level.  Use volume control keys to change the

setting. The adjustment is stored automatically.

•••••

 Press the    Red     button three times to enter “FACTORY COLOUR” level.  Use volume control keys to change the

setting. The adjustment is stored automatically.

•••••

 If buttons 0 through 9 are pressed, the set will automatically go to that program number.

   Note that in case the blue button has been used before, the program number should be requested by using two

digit number (01...99).

•••••

 By pressing the Menu button, the unit will normalise Picture and Audio settings. The Auto Installation is then

turned “on”.

SERVICE SOFTWARE 32KF84H 

∗∗

-

∗∗∗∗∗

SW on: XXXX   SW off: XXXX   Hours ON: XXXX

The following geometry adjustments can be carried out.  Detailed instructions on how to execute these are given on the
following pages:

• 

Horizontal Shift

• 

East West Width

• 

Pin Phase

• 

Pin Amp

• 

Vertical angle

• 

Vertical bow

• 

Upper Corner Amplitude

• 

Lower Corner Symmetry

• 

Extreme Corner Symmetry

• 

Vertical Amplitude

• 

S Correction

• 

Vertical Shift

• 

Vertical Linearity

Just in case the TV set requires a full geometry adjustment, please proceed  first with Verti-
cal according to the above order, and after that,  adjust Horizontal according to the above
order.

Adjust the horizontal shift so that the picture is centred.
The effect of this adjustment is shown in figure 2.

•

 When the volume up button is pressed, the picture moves to the left.

•

 When the volume down button is pressed, the picture moves to the right.

•

 Press the stand-by button on the remote control to store.

Adjust the East West Width so that 8% over-scan is achieved.
The effect of this adjustment is shown in figure 3.

•

 When the volume up button is pressed, horizontal scanning increases.

•

 When the volume down button is pressed, horizontal scanning decreases.

•

 Press the stand-by button on the remote control to store.

Adjust the Pin Phase so that the picture is symmetrical top and bottom.
The effect of this adjustment is shown in figure 4.

•

 When the volume up button is pressed, side pincushion changes.

•

 When the volume down button is pressed, side pincushion changes.

•

 Press the stand-by button on the remote control to store.

Adjust the Pin Amplitude so that the picture is centred.
The effect of this adjustment is shown in figure 5.

•

 When the volume up button is pressed, side pincushion changes from pincushion to

barrel shape.

•

 When the volume down button is pressed, side pincushion changes from barrel

shape to pincushion.

•

 Press the stand-by button on the remote control to store.

Figure 2

Figure 3

Figure 4

Figure 5

Adjust the Upper Corner Correction so that the picture is centred.
The effect of this adjustment is shown in figure 6.

• 

When the volume up button is pressed, side pincushion changes from pincushion to

barrel shape.

•

 When the volume down button is pressed, side pincushion changes from barrel shape to

pincushion.

•

 Press the stand-by button on the remote control to store.

Adjust the Lower Corner Correction so that the picture is centred.
The effect of this adjustment is shown in figure 7.

• 

When the volume up button is pressed, side pincushion changes from pincushion to

barrel shape.

• 

When the volume down button is pressed, side pincushion changes from barrel shape to

pincushion.

• 

Press the stand-by button on the remote control to store.

Adjust the Extreme Corner Correction so that the picture is centred.
The effect of this adjustment is shown in figure 8.

• 

When the volume up button is pressed, side pincushion changes from pincushion to

barrel shape.

•

 When the volume down button is pressed, side pincushion changes from barrel shape to

pincushion.

•

 Press the stand-by button on the remote control to store.

Adjust the Vertical Linearity so that the upper and lower parts of the picture are symmetrical.
The effect of this adjustment is shown in figure 9.

• 

When the volume up button is pressed, the upper picture scanning decreases and the

lower picture scanning increases.

• 

When the volume down button is pressed, the upper picture scanning increases and the

lower picture scanning decreases.

• 

Press the stand-by button on the remote control to store.

Adjust the Vertical Angle so that the picture is centred.
The effect of this adjustment is shown in figure 10.

• 

When the volume up button is pressed, the vertical angle changes to right.

• 

When the volume down button is pressed, the vertical angle changes to left.

• 

Press the stand-by button on the remote control to store.

Figure 9

Figure 7

Figure 10

Figure 6

Figure 8