DOWNLOAD Sony DCR-PC101 / DCR-PC101E (serv.man2) Service Manual ↓ Size: 6.01 MB | Pages: 127 in PDF or view online for FREE

Press ZERO SET MEMORY again after step 5 to erase the ZERO SET MEMORY
indicator and begin from step 3.

Note
The picture and sound recorded on the section between the insert start and end points
will be erased when you insert the new scene.

If you insert scenes on the tape recorded with other camcorder (including other
DCR-PC101)
The picture and sound may be distorted. We recommend that you insert scenes on a
tape recorded with your camcorder.

When the inserted picture is played back
The picture and sound may be distorted at the end of the inserted section. This is not a
malfunction.
The picture and sound at the start point and the end point may be distorted in the LP
mode.

To insert a scene without setting the insert end point
Skip step 3 and 4. Press x on the Remote Commander or 

 on your camcorder when

you want to stop inserting.

If you press FN
The ZERO SET MEMORY indicator is not displayed.

FN

ZERO SET

MEMORY

0:00:00

ZERO SET

MEMORY

REC

PAUSE

REC

START

REC CTRL

RET.

You can record additional audio to the original sound on a tape by connecting audio
equipment or a microphone. If you connect the audio equipment, you can add sound to
your tape already recorded in the 12-bit mode by specifying starting and ending points.
The original sound will not be erased.
Select one of the following connections to add additional audio.

You can check the recorded picture and sound by connecting the A/V jack to a TV.
The recorded sound is not output from a speaker. Check the sound by using the
headphones or TV.

Microphone (optional)

Intelligent accessory shoe

MIC (PLUG IN
POWER)

Microphone
(optional)

: Signal flow

No connection is necessary.

Note
When dubbing with the A/V jack or the built-in microphone, pictures are not output
through the S VIDEO jack or A/V jack. Check the recorded picture on the screen. You
can check the recorded sound by using headphones.

If you make all the connections
The audio input to be recorded will take precedence over others in the following order.
•MIC (PLUG IN POWER) jack
•Intelligent accessory shoe
•A/V jack
•Built-in microphone

LINE OUT

L

R

AUDIO R

Audio equipment

Do not connect the
video (yellow) plug.

: Signal flow

White

Red

A/V connecting cable (supplied)

AUDIO L

FN

PAGE1 PAGE2 PAGE3 EXIT

DATA

CODE

AUDIO

DUB

REC
CTRL

REC

PAUSE

RET.

PAGE1 PAGE2 PAGE3 EXIT

DATA

CODE

AUDIO

DUB

REC
CTRL

REC

PAUSE

RET.

PAGE1 PAGE2 PAGE3 EXIT

DATA

CODE

AUDIO

DUB

REC
CTRL

REC

PAUSE

RET.

PAGE1 PAGE2 PAGE3 EXIT

DATA

CODE

AUDIO

DUB

REC
CTRL

REC

PAUSE

RET.

PAGE1 PAGE2 PAGE3 EXIT

DATA

CODE

AUDIO

DUB

REC
CTRL

REC

PAUSE

RET.

PAGE1 PAGE2 PAGE3 EXIT

DATA

CODE

AUDIO

DUB

REC
CTRL

REC

PAUSE

RET.

PAGE1 PAGE2 PAGE3 EXIT

DATA

CODE

AUDIO

DUB

REC
CTRL

REC

PAUSE

RET.

PAGE1 PAGE2 PAGE3 EXIT

V  SPD

PLAY

A  DUB

CTRL

REC
CTRL

A  DUB  CTRL     

RET.

REC

START

REC

START

REC

START

REC

START

REC

START

REC

START

REC

START

AUDIO
DUB

To add new sound more precisely
Press ZERO SET MEMORY at the point where you want to stop recording later in
playback.
Carry out step 3. Recording automatically stops at the point where ZERO SET
MEMORY was pressed.

Choose a connection mentioned before, and connect audio equipment or microphone to
your camcorder. Then follow the procedure below.

(1) Insert your recorded tape into your camcorder.
(2) Set the POWER switch to VCR.
(3) Locate the recording start point. Press 

 to start playing back. To pause

playing back, press 

 at the recording start point. You can fine adjust the

recording start point by pressing 

/

.

(4) Press FN, then select PAGE3.
(5) Press A DUB CTRL to display control buttons.
(6) Press AUDIO DUB. The green  X appears on the LCD screen.
(7) Press 

 on your camcorder and at the same time start playing back the

audio you want to record.
The new sound is recorded in stereo 2 (ST2) during playback. While recording
new sound, the red   appears on the LCD screen.

(8) Press 

 on your camcorder at the point where you want to stop recording.