Sony DCR-PC101 / DCR-PC101E (serv.man2) Service Manual ▷ View online
85
Editing
You can duplicate selected scenes (programs) for editing onto a tape without operating
the VCR.
Scenes can be selected by frame. You can set up to 20 programs.
Your camcorder can dub on “Memory Stick”s. See page 143 for more information.
the VCR.
Scenes can be selected by frame. You can set up to 20 programs.
Your camcorder can dub on “Memory Stick”s. See page 143 for more information.
Before operating the Digital program editing on tapes
recorded on other equipment
recorded on other equipment
Step 1
Connecting to the VCR (p. 85).
Step 2
Setting the VCR to operate (p. 86, 90).
Step 3
Adjusting the synchronization of the VCR (p. 92).
When you dub using the same VCR again, you can skip steps 2 and 3.
Using the Digital program editing function on tapes recorded
on other equipment
on other equipment
Operation 1 Making the program (p. 94).
Operation 2 Performing Digital program editing (Dubbing a tape) (p. 96).
Operation 2 Performing Digital program editing (Dubbing a tape) (p. 96).
Note
When editing digital video, the operation signals to the VCR cannot be sent with
LANC .
When editing digital video, the operation signals to the VCR cannot be sent with
LANC .
Step 1: Connecting to the VCR
You can connect either the A/V connecting cable or the i.LINK cable .
When you use the A/V connecting cable, connect the devices as illustrated in page 83.
When you use the i.LINK cable, connect the devices as illustrated in page 84.
When you use the A/V connecting cable, connect the devices as illustrated in page 83.
When you use the i.LINK cable, connect the devices as illustrated in page 84.
If you connect using an i.LINK cable
With digital-to-digital connection, video and audio signals are transmitted in digital
form for high-quality editing.
With digital-to-digital connection, video and audio signals are transmitted in digital
form for high-quality editing.
Dubbing only desired scenes
– Digital program editing (on tapes)
– Digital program editing (on tapes)
Unwanted
scene
Unwanted
scene
Switch the order
86
Dubbing only desired scenes – Digital program editing (on tapes)
Step 2: Setting the VCR to operate with the A/V connecting cable
To edit using the VCR, send the control signal by infrared rays to the remote sensor on
the VCR.
When you connect using the A/V connecting cable, follow the procedures below, (1) to
(4), to send the control signal correctly.
the VCR.
When you connect using the A/V connecting cable, follow the procedures below, (1) to
(4), to send the control signal correctly.
(1) Setting the IR SETUP code
1
Set the POWER switch to VCR on your camcorder.
2
Turn the power of the connected VCR on, then set the input selector to
LINE.
When you connect a video camera recorder, set its power switch to VCR/
VTR.
LINE.
When you connect a video camera recorder, set its power switch to VCR/
VTR.
3
Press FN to display PAGE1.
4
Press MENU, then select VIDEO EDIT in
, then press EXEC (p. 192).
5
Press
r/R to select TAPE, then press EXEC.
6
Press EDIT SET.
7
Press
r/R to select CONTROL, then press EXEC.
8
Press
r/R to select IR, then press EXEC.
9
Press
r/R to select IR SETUP, then press EXEC.
0
Press
r/R to select the IR SETUP code of your VCR, then press EXEC.
Check the code in “About the IR SETUP code” (p. 88).
87
Editing
Dubbing only desired scenes – Digital program editing (on tapes)
4
5
6
8~10
7
3
FN
OTHERS
DATA CODE
BEEP
COMMANDER
D I SPL AY
V I DEO ED I T
BEEP
COMMANDER
D I SPL AY
V I DEO ED I T
EXIT
RET.
EXEC
READY
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
END
RET.
EXEC
I R
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
EXIT
RET.
EXEC
3
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
I R
i. L I NK
i. L I NK
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
I R
V I DEO ED I T
ED I T SET
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
CONTROL
ADJ TEST
”CUT - I N”
”CUT -OUT”
I R SETUP
PAUSEMODE
I R TEST
RET.
EXEC
1
END
END
END
0:32:30:14
TOTAL
SCENE
SCENE
0:00:00:00
0
0
V I DEO ED I T
MARK
I N
I N
START
ED I T
SET
SET
UNDO
END
OTHERS
DATA CODE
BEEP
COMMANDER
D I SPL AY
V I DEO ED I T
BEEP
COMMANDER
D I SPL AY
V I DEO ED I T
EXIT
RET.
EXEC
RETURN
TAPE
MEMORY
TAPE
MEMORY
88
About the IR SETUP code
The IR SETUP code is stored in the memory of your camcorder. Be sure to set the
The IR SETUP code is stored in the memory of your camcorder. Be sure to set the
correct code, depending on your VCR. Default setting is code number 3.
Dubbing only desired scenes – Digital program editing (on tapes)
Note on the IR SETUP code
Digital program editing is not possible if the VCR does not support IR SETUP codes.
Digital program editing is not possible if the VCR does not support IR SETUP codes.
* TV/VCR component
Brand
IR SETUP code
Brand
IR SETUP code
Click on the first or last page to see other DCR-PC101 / DCR-PC101E (serv.man2) service manuals if exist.