DOWNLOAD Sony CFD-V8L Service Manual ↓ Size: 2.11 MB | Pages: 41 in PDF or view online for FREE

AEP Model

2004I02-1

© 2004.09

– Continued on next page –

CD player section
System

Compact disc digital audio system

Laser diode properties

Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 

µW

(This output is the value measured at a distance of about 200 mm from
the objective lens surface on the optical pick-up block with 7 mm
aperture.)

Spindle speed

200 r/min (rpm) to 500 r/min (rpm) (CLV)

Number of channels

2

Frequency response

20 - 20 000 Hz +1/–2 dB

Wow and flutter

Below measurable limit

Frequency range

FM 87.6 - 107 MHz

LW 153 - 279 kHz

IF

FM: 10.7 MHz
LW: 455 kHz

Aerials

FM: Telescopic aerial
LW: Built-in ferrite bar aerial

Cassette-corder section
Recording system

4-track 2 channel stereo

Fast winding time

Approx. 120 s (sec.) with Sony cassette C-60

Frequency response

TYPE I (normal): 80 - 10 000 Hz

General
Speaker

Model Name Using

CD Section

CFD-V8

Similar Mechanism

Tape Section

CFD-V8

CD Mechanism Type (Former Type/New Type)

KSM-213RDP/KSM-213CDP

Optical Pick-up Type (Former Type/New Type)

KSS-213R/KSS-213C

Tape Transport Mechanism Type

MF-V5-117

2

Specifications ............................................................................ 1

................................................ 3

Location and Function of Controls .................................. 4

3-1.   Cabinet (Front) Sub ASSY, Cabinet (Rear) ........... 5
3-2.   Control Board ......................................................... 5
3-3.   Cabinet (upper) ...................................................... 6
3-4.   Power Board, Inlet Board, BATT (R) Board,
         BATT (L) Board ..................................................... 6
3-5.   Volume Board, FM SW Board, Main Board .......... 7
3-6.   PRE Board, Mechanism Deck,
         Optical Pick-up Section, CD Board ....................... 7
3-7.   Belt, M601 (Capstan / Reel Motor),
         “HRP901 Head, Magnetic (Record/Playback)”,
         HE901 Head (Erase) ............................................... 8
3-8.   Optical Pick-up (KSS-213C) ................................. 8

......................... 9

5-1.   Mechanical Adjustments ........................................ 10
5-2.   Electrical Adjustments ........................................... 10

6-1.   IC Pin Function Descrintion .................................. 13
6-2.   Block Diagrams – Tuner/TC Section – .................. 15
6-3.   Block Diagrams – Main Section – ......................... 16
6-4.   Block Diagrams – CD Section – ............................ 17
6-5.   Printed Wiring Boards – Main Section – ............... 18
6-6.   Schematic Diagrams – Main Section (1/3) – ......... 19
6-7.   Schematic Diagrams – Main Section (2/3) – ......... 20
6-8.   Schematic Diagrams – Main Section (3/3) – ......... 21
6-9.   Printed Wiring Boards
         – Control/Power Section – ..................................... 22
6-10. Printed Wiring Boards – Control/Power Section – 23
6-11. Schematic Diagrams – CD Section – ..................... 24
6-12. Printed Wiring Boards – CD Section – .................. 25

7-1.   Front Cabinet Section ............................................. 30
7-2.   Rear Cabinet Section .............................................. 31
7-3.   Upper Cabinet Section ........................................... 32
7-4.   Mechanism Deck Section (1) ................................. 33

.................................. 36

0

0

Full range: 10 cm dia., 3.2 

Ω, cone type (2)

Outputs

Headphones jack (stereo minijack)
For 16 - 68 

Ω impedance headphones

Maximum power output

3.6 W

Power requirements

For CD radio cassette-corder: 230 V AC, 50 Hz
9 V DC, 6 R20 (size D) batteries

Power consumption

AC 20 W

Battery life

For CD radio cassette-corder:

Sony R20P: approx. 13.5 h

Sony alkaline LR20: approx. 20 h

Sony R20P: approx. 7.5 h

Sony alkaline LR20: approx. 15 h

Sony R20P: approx. 2.5 h

Sony alkaline LR20: approx. 7 h

Dimensions

Approx. 420 x 165 x 256 mm (w/h/d)
(16 

5

⁄

8

 x 6 

1

⁄

2

 x 10 

1

⁄

8

 inches) (incl. projecting parts)

Mass

Approx. 4.1 kg (9 lb. 1 oz) (incl. batteries)

Supplied accessory

Mains lead (1)

Design and specifications are subject to change without notice.

3

The laser diode in the optical pick-up block may suffer electro-
static breakdown because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled
with care.

The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode
emission, observe more than 30 cm away from the  objective
lens.

On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.

• Code number of Chuck Plate Jig : X-4918-255-1

1. Press CD open knob.
2. Open the lid for CD.
3. Push on SWITCH (S801) as following figure.
4. Confirm the laser diode emission while observing the objecting

lens. When there is no emission, Auto Power Control circuit
or Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.

Insert a precision 
screw driver and push  
SWITCH (S801)

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°C.

Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

4

This section is extracted
from instruction manual.

Z

i

.

>

u

x

C

D

E