Sony DCR-IP5 / DCR-IP5E / DCR-IP7BT / DCR-IP7E (serv.man3) Service Manual ▷ View online
5-7
DCR-IP5/IP5E/IP7BT/IP7E
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1.
POWER (FK-1900 block) ...................................... CAMERA
2.
FUNCTION settings
FOCUS ............................................................. MANUAL
EXPOSURE ................................................................ OFF
MANUAL SET of the MENU settings
EXPOSURE ................................................................ OFF
MANUAL SET of the MENU settings
PROGRAM AE ................................................ AUTO
PICTURE EFFECT .............................................. OFF
WHITE BALANCE .......................................... AUTO
PICTURE EFFECT .............................................. OFF
WHITE BALANCE .......................................... AUTO
CAMERA SET of the MENU settings
DIGITAL ZOOM .................................................. OFF
16:9 WIDE ............................................................ OFF
STEADY SHOT ................................................... OFF
16:9 WIDE ............................................................ OFF
STEADY SHOT ................................................... OFF
SETUP MENU of the MENU settings
DEMO MODE ...................................................... OFF
DIGITAL EFFECT ............................................... OFF
DIGITAL EFFECT ............................................... OFF
3.
BACK LIGHT (FP-366 flexible) ..................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig.5-1-4.
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
×
841mm) black and white vellum paper.
Fig. 5-1-5.
Note:
Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
the black and white paper joined together are not rough.
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
White
Black
841mm
1189mm
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame )
5-8
DCR-IP5/IP5E/IP7BT/IP7E
1-2.
INITIALIZATION OF B, C, D, E, F, 4, 7, 8, 9
PAGE DATA
PAGE DATA
1-2-1.
INITIALIZATION OF D, E, F, 7 PAGE DATA
1. Initializing the D, E, F, 7 Page Data
Note1: If “Initializing the D, E, F, 7 Page Data” is performed, all
data of the D page, E page, F page and 7 page will be
initialized. (It is impossible to initialize a single page.)
initialized. (It is impossible to initialize a single page.)
Note2:
If the D, E, F, 7 page data has been initialized, the following
adjustments need to be performed again.
1) Modification of D, E, F, 7 page data
2) Camera system adjustments
adjustments need to be performed again.
1) Modification of D, E, F, 7 page data
2) Camera system adjustments
Note3:
NTSC model: DCR-IP5/IP7BT
PAL model: DCR-IP5E/IP7E
PAL model: DCR-IP5E/IP7E
Switch setting:
POWER .................................................................. CAMERA
Adjusting page
D
Adjusting Address
10 to FF
Adjusting page
E
Adjusting Address
00 to FF
Adjusting page
F
Adjusting Address
10 to FF
Adjusting page
7
Adjusting Address
00 to FF
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
2
00
Set the following data.
2F (NTSC), 37 (PAL)
2F (NTSC), 37 (PAL)
3
2
01
Set the following data, and press
the PAUSE button.
2F (NTSC), 37 (PAL)
the PAUSE button.
2F (NTSC), 37 (PAL)
4
2
02
Check that the data changes from
“00” to “01”
“00” to “01”
5
Perform “Modification of D, E,
F, 7 Page Data”.
F, 7 Page Data”.
2. Modification of D, E, F, 7 Page Data
If the D, E, F, 7 page data has been initialized, change the data of
the “Fixed data-2” address shown in the following tables by manual
input.
the “Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camcorder may
not operate.
not operate.
3)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of D, E, F, 7 Page
data
data
Order Page Address Data
Procedure
1
2
00
29
Set the data
2
2
01
29
Set the data, and press the PAUSE
button.
button.
Note:
If the following symptoms occur after completing of the
“Modification of D, E, F, 7 page data”, check that the data of the
“Fixed data-2” addresses of D page are same as those of the same
model of the same destination.
1) The battery end mark on the LCD or viewfinder screen is flashing.
2) The power is shut off so that unit cannot operate.
“Modification of D, E, F, 7 page data”, check that the data of the
“Fixed data-2” addresses of D page are same as those of the same
model of the same destination.
1) The battery end mark on the LCD or viewfinder screen is flashing.
2) The power is shut off so that unit cannot operate.
3. D Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
Table. 5-1-2.
00 to 0F
10
11
12
13 to 20
21
22 to 26
27
28
29 to 2C
2D
2E
2F
30
31
32
33 to 38
39
3A to 3B
3C
3D to FF
00
Test mode
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
00
Address
Remark
Initial value
NTSC PAL
5-9
DCR-IP5/IP5E/IP7BT/IP7E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66 to 68
69
6A
6B
6C to 6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85 to B7
B8
B9 to FF
1E
80
80
40
C0
40
C0
40
C0
40
C0
AD
FF
19
00
49
00
00
00
00
00
00
80
80
00
0C
34
09
70
07
AA
06
28
06
00
40
00
3A
00
31
00
31
00
35
1E
1E
80
80
40
C0
40
C0
40
C0
40
C0
AD
FF
19
00
49
00
00
00
00
00
00
80
80
00
0C
34
09
70
07
AA
06
28
06
00
40
00
3A
00
31
00
31
00
35
1E
Flange back adj.
MR adj.
Flange back adj.
Fixed data-1
Flange back adj.
Fixed data-1
Flange back adj.
Fixed data-1
Optical axis adj.
MR adj.
Fixed data-1
Mechanical shutter adj.
Fixed data-1
Fixed data-2
Fixed data-1
00 to 0F
10 to 11
12
13 to 15
16
17
18
19
1A
1B
1C
1D
1E
1F
20 to 23
24
25
26
27
28
29
2A
2B
2C
2D
2E to 2F
30
31
32
33
34
35
36
37
38 to 3B
3C
3D
3E to 3F
40
41
42 to 45
46
47
48
49
4A
4B
4C
4D
4E
80
19
61
91
88
77
54
88
90
80
7A
80
80
80
80
00
80
80
80
80
00
A2
39
2E
54
32
20
04
F3
9E
6D
00
00
00
00
DB
33
4F
2F
A9
Fixed data-1
48MHz origin osc adj.
Fixed data-1
HALL adj.
MAX GAIN adj.
LV standard data input
Fixed data-1
F No. & ND light quantity
standard data input
Fixed data-1
AWB standard data input
Fixed data-1
Color reproduction adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Auto white balance adj.
Fixed data-1
LV standard data input
(ND spectrum compensation)
Flange back adj.
80
19
61
91
88
77
54
88
90
80
7A
80
80
80
80
00
80
80
80
80
00
A2
39
2E
54
32
20
04
F3
9E
6D
00
00
00
00
DB
33
4F
2F
A9
Address
Remark
Initial value
NTSC PAL
Address
Remark
Initial value
NTSC PAL
4. F Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
Table. 5-1-3.
5-10
DCR-IP5/IP5E/IP7BT/IP7E
5. E Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
6. 7 Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
00 to 1C
1D
1E
1F
20
21 to FF
80
80
80
80
Fixed data-1
Mechanical shutter adj.
Fixed data-1
80
80
80
80
Address
Remark
Initial value
NTSC PAL
Table. 5-1-5.
00 to 04
05
06 to 9E
9F
A0 to FF
10 (*1)
18 (*2)
1C
Address
Remark
Initial value
NTSC PAL
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data
Fixed data-1
Table. 5-1-4.
*1: HI/camera microprocessor ver. 1.0.
*2: HI/camera microprocessor ver. 2.0. or later.
*2: HI/camera microprocessor ver. 2.0. or later.
Version check of the HI/camera microprocessor:
(VC-263 board IC1203)
(VC-263 board IC1203)
Order Page Address Data
Procedure
1
2
FF
The data shows the version of
the HI/camera microprocessor.
Example: “02” shows version
2.0
the HI/camera microprocessor.
Example: “02” shows version
2.0
Click on the first or last page to see other DCR-IP5 / DCR-IP5E / DCR-IP7BT / DCR-IP7E (serv.man3) service manuals if exist.