DOWNLOAD Sony CCD-TRV107 / CCD-TRV108 / CCD-TRV308 / CCD-TRV408 / CCD-TRV608 Service Manual ↓ Size: 16.83 MB | Pages: 127 in PDF or view online for FREE

5-20

Precautions on the Parts Replacement
There are two types of repair parts.

Type A: ENC03JA
Type B: ENC03JB

Replace the broken sensor with a same type sensor. If replace with
other type parts, the image will vibrate up and down or left and
right during hand-shake correction operations. After replacing, check
the steady shot operation according to the following method.

Precautions on Angular Velocity Sensor
The sensor incorporates a precision oscillator. Handle it with care
as if it dropped, the balance of the oscillator will be disrupted and
operations will not be performed properly.

Subject

Arbitrary

Measurement Point

Display data of page 1 (Note)

Measuring Instrument

Adjustment remote commander

Specified Value

2700 to 5100

Note: Displayed data of the adjustment remote commander.

1 : XX : XX

Display data

Switch setting:
1)

STEADY SHOT (Menu display) ...................................... ON

2)

ZOOM .................................................................... TELE end

Pitch sensor check
(SI-033 board SE750)

1

0

03

11

Set the data.

2

1

Check that the display data (Note1)
satisfies the specified value.

Yaw sensor check
(SI-033 board SE751)

3

0

03

12

Set the data.

4

1

Check that the display data (Note1)
satisfies the specified value.

5

Move the camcorder, and check
that the steady shot operations
have been performed normally

1

0

03

00

Set the data.

5-21

Electronic viewfinder system adjustment is unnecessary with the
EVF TYPE M model.
EVF TYPE S model: CCD-TRV107/TRV308/ TRV408/TRV608
EVF TYPE M model: CCD-TRV108

When replacing the LCD unit, be careful to prevent damages
caused by static electricity.

Most of the measuring points for adjusting the viewfinder system
are concentrated in CN713 of VC-272 board.
Connect the Measuring instruments and the adjustment remote
commander via the I/F unit for LANC control (J-6082-521-A) and
CPC jig connector (J-6082-539-A) to CN713. To operate the
adjustment remote commander, connect the AC power adapter to
the DC IN jack of I/F unit for LANC control, or connect the L
series Info-LITHIUM battery to the battery terminal of I/F unit for
LANC control.
The following table shows the Pin No. and signal name of CN713.

Table 5-1-6.

The following table shows the arrangement of the test points of I/F
unit for LANC control. (Pin No. are those of CN713.)

Table 5-1-7.

1

2

3

4

5

6

7

8

N.C.

IR VIDEO

BPF MONI

CAP FG

RF SWP

REG GND

REC RF

REG GND

9

10

11

12

13

14

15

16

PB RF

REG GND

LANC OUT

LANC IN

XLANC POWER ON

EVF VG

VCO

N.C.

14

9

3

5

4

BL

EVF VG

PB RF (MON)

BPF MONI

TMS

TDI

SWP

CAP FG

15

6,8,10

7

2

EVF VCO

BL 4.75

GND

REC RF (RF IN)

TDO

TCK

IR VIDEO

Fig. 5-1-13.

CPC jig connector

CPC jig

Remove the CPC lid

CN713

Conductor side

16

1

5-22

1. RGB AMP Adjustment (VF-150 board)
Set the D range of the RGB driver used to drive the LCD to the
specified value. If deviated, the LCD screen will become blackish
or saturated (whitish).

Note: Do either of the automatic adjustment or the manual adjustment.

Mode

Camera

Subject

Arbitrary

Adjustment Page

7

Adjustment Address

36

1

0

01

01

Set the data.

2

6

01

E3

Set the data, and press PAUSE
button.

3

6

02

Check that the data changes from
“00” to “01”.

4

6

01

00

Set the data, and press PAUSE
button.

5

0

01

00

Set the data.

Mode

Camera

Subject

Arbitrary

Measurement Point

EVF VG
(Pin qf of CN713 of VC-272 board)

Measuring Instrument

Oscilloscope

Adjustment Page

7

Adjustment Address

36

Specified Value

A = 7.35 ± 0.27V

1

0

01

01

Set the data.

2

7

36

Change the data and set the
voltage (A) between the reversed
waveform pedestal and non-
reversed waveform pedestal to the
specified value.

3

7

36

Press PAUSE button.

4

0

01

00

Set the data.

Fig. 5-1-14.

5-23

2. Contrast Adjustment (VF-150 board)
Set the level of the VIDEO signal for driving the LCD to the specified
value. If deviated, the screen image will be blackish or saturated
(whitish).

Note: Do either of the automatic adjustment or the manual adjustment.

Mode

Camera

Subject

Arbitrary

Adjustment Page

7

Adjustment Address

3A

1

0

01

01

Set the data.

2

6

01

E5

Set the data, and press PAUSE
button.

3

6

02

Check that the data changes
from “00” to “01”.

4

6

01

00

Set the data, and press PAUSE
button.

5

0

01

00

Set the data.

Mode

Camera

Subject

Arbitrary

Measurement Point

EVF VG
(Pin qf of CN713 of VC-272 board)

Measuring Instrument

Oscilloscope

Adjustment Page

7

Adjustment Address

3A

Specified Value

A = 2.32 ± 0.12V

1

0

01

01

Set the data.

2

7

3A

Change the data and set the
voltage (A) between the 100 IRE
and 0 IRE (pedestal) to the
specified value.
(The data should be “00” to “7F”.)

3

7

3A

Press PAUSE button.

4

0

01

00

Set the data.

Fig. 5-1-15.