Sony DSC-KW1 / DSC-KW11 Service Manual ▷ View online
DSC-KW1/KW11
2-1
2-1. NOTES FOR FLEXIBLE BOARD
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
and completely)
NG
(The flexible board was plugged in
crooked.)
crooked.)
NG
(The flexible board was not plugged in
completely.)
completely.)
Flexible
Board
Flexible
Board
Board
Connector
Connector
Reference line
Flexible
Board
Board
Connector
Connector
Flexible
Board
Reference line
Connector
Connector
Flexible
Board
Board
Flexible
Board
Reference line
Fig. 1
Fig. 2
Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
a flexible board in direction B.
Holder
Connector
Flexible Board
A
A
Holder
Insulation side
Connector
Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.
broken.
2. SERVICE NOTE
DSC-KW1/KW11
2-2
2-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the MENU screen. (When erasing the data, execute formatting the internal memory.)
Note 1: When replacing the Main Board Assy, erase the data in internal memory of the board before replacement.
Note 2: When replacing the Main Board Assy, execute formatting and initialize the internal memory after replacement.
Note 2: When replacing the Main Board Assy, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
&RS\
&RSLHVDOOLPDJHVLQWKHLQWHUQDOPHPRU\WRDPHPRU\FDUG
,QVHUWDPHPRU\FDUGZLWKVXIILFLHQWIUHHFDSDFLW\LQWRWKHFDPHUD
0(18
6HWWLQJV
0HPRU\&DUG7RRO>&RS\@>2.@
1RWH
0DNHVXUHWKHUHLVVXIILFLHQWEDWWHU\SRZHU2WKHUZLVHWKHEDWWHU\SRZHUPD\UXQRXWZKHQ\RXDWWHPSWWRFRS\
LPDJHILOHVFDXVLQJWKHFRS\WRIDLODQGSRVVLEO\FRUUXSWWKHGDWD
,PDJHVFDQQRWEHFRSLHGLQGLYLGXDOO\
2ULJLQDOLPDJHVLQLQWHUQDOPHPRU\DUHUHWDLQHGHYHQDIWHUFRS\LQJ7RGHOHWHFRQWHQWVRILQWHUQDOPHPRU\UHPRYH
WKHPHPRU\FDUGDIWHUFRS\LQJWKHQIRUPDWLQWHUQDOPHPRU\>)RUPDW@LQ>,QWHUQDO0HPRU\7RRO@
7KHGDWDZLOOEHFRSLHGWRWKHUHFRUGLQJIROGHUWKDWLVFXUUHQWO\EHLQJXVHGZLWKDQXPEHURQHKLJKHUWKDQWKH
ODUJHVWGDWDQXPEHULQWKDWIROGHU
LPDJHILOHVFDXVLQJWKHFRS\WRIDLODQGSRVVLEO\FRUUXSWWKHGDWD
,PDJHVFDQQRWEHFRSLHGLQGLYLGXDOO\
2ULJLQDOLPDJHVLQLQWHUQDOPHPRU\DUHUHWDLQHGHYHQDIWHUFRS\LQJ7RGHOHWHFRQWHQWVRILQWHUQDOPHPRU\UHPRYH
WKHPHPRU\FDUGDIWHUFRS\LQJWKHQIRUPDWLQWHUQDOPHPRU\>)RUPDW@LQ>,QWHUQDO0HPRU\7RRO@
7KHGDWDZLOOEHFRSLHGWRWKHUHFRUGLQJIROGHUWKDWLVFXUUHQWO\EHLQJXVHGZLWKDQXPEHURQHKLJKHUWKDQWKH
ODUJHVWGDWDQXPEHULQWKDWIROGHU
Method for Formatting the Internal Memory or Memory Card
)RUPDW
:KHQ\RXXVHDPHPRU\FDUGZLWKWKLVFDPHUDIRUWKHILUVWWLPHLWLVUHFRPPHQGHGWRIRUPDWWKHFDUGXVLQJWKH
FDPHUDIRUVWDEOHSHUIRUPDQFHRIWKHPHPRU\FDUGEHIRUHVKRRWLQJ1RWHWKDWIRUPDWWLQJSHUPDQHQWO\HUDVHVDOOGDWD
RQWKHPHPRU\FDUGDQGLVXQUHFRYHUDEOH6DYHSUHFLRXVGDWDRQDFRPSXWHUHWF
FDPHUDIRUVWDEOHSHUIRUPDQFHRIWKHPHPRU\FDUGEHIRUHVKRRWLQJ1RWHWKDWIRUPDWWLQJSHUPDQHQWO\HUDVHVDOOGDWD
RQWKHPHPRU\FDUGDQGLVXQUHFRYHUDEOH6DYHSUHFLRXVGDWDRQDFRPSXWHUHWF
0(18
6HWWLQJV
0HPRU\&DUG7RRORU
,QWHUQDO0HPRU\7RRO>)RUPDW@>2.@
1RWH
1RWHWKDWIRUPDWWLQJSHUPDQHQWO\HUDVHVDOOGDWDLQFOXGLQJHYHQSURWHFWHGLPDJHV
DSC-KW1/KW11
2-3
2-3. NOTE ON MAIN BOARD ASSY REPLACEMENT
In case of replacing the MAIN BOARD ASSY, it is necessary to erase the customer’s data from the board to be replaced.
Thus, before replacing the board, perform [Initialize] and [Format].
Thus, before replacing the board, perform [Initialize] and [Format].
Methoid for Initializing the Internal Memory or Memory Card
,QLWLDOL]H
,QLWLDOL]HVVHWWLQJVWRWKHGHIDXOWVHWWLQJ
(YHQLI\RXH[HFXWHWKLVIXQFWLRQLPDJHVDUHUHWDLQHG
(YHQLI\RXH[HFXWHWKLVIXQFWLRQLPDJHVDUHUHWDLQHG
0(18
6HWWLQJV
0DLQ6HWWLQJV>,QLWLDOL]H@>2.@
1RWH
%HVXUHQRWWRUHPRYHWKHEDWWHU\SDFNZKLOHLQLWLDOL]LQJ
For [Format], refer to “2-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY”.
When replacing with a MAIN BOARD ASSY, implement the work below.
• Perform the adjustments and Set Language Destination
When replacing with a MAIN BOARD ASSY, implement the work below.
• Perform the adjustments and Set Language Destination
referring to “4. ADJUSTMENT”.
• Search the access point as concise operation confirmation of wireless LAN.
Note: After the replacement and repair, the MAC address is changed, and thus the resetting for connection devices is required. Accordingly, print out the flyer
given at the last page of this service manual and attach it to the set when returning the set to customer.
2-4. NOTE ON NFC PC BOARD OR MAIN BOARD ASSY REPLACEMENT
After replacing the NFC PC BOARD or MAIN BOARD ASSY, Perform [SSID/PW Reset].
SSID/PW Reset
This product shares the connection information for [Send to Smartphone] and [Ctrl with Smartphone] with a device
that has permission to connect. If you want to change the device that is permitted to connect, reset the connection
information.
that has permission to connect. If you want to change the device that is permitted to connect, reset the connection
information.
1. MENU - @ (Wireless) - [SSID/PW Reset] - [OK]
Note
After resetting the connection information, and if you connect this product to the smartphone, you must register the
smartphone again.
smartphone again.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2014.10
DSC-KW1/KW11
3-1
3. DISASSEMBLY & ASSEMBLY
3-1. IDENTIFYING PARTS
1
Rear Cover Assy
2
Rear Inner Assy
6
Microphone
4
Speaker
5
Chassis Assy
9
Top Cover Assy
q;
Lens Assy
qa
NFC Board
3
Antenna
7
Main Board Assy
8
Display Bracket Assy
qd
Front Cover Assy
qs
TP OLED Block Assy
Click on the first or last page to see other DSC-KW1 / DSC-KW11 service manuals if exist.