Sony DSC-KW1 / DSC-KW11 Service Manual ▷ View online
4-12
DSC-KW1/KW11
4-3-7. Lens Option
Lens Option Setting order is as follows.
1) Check that the camera is on the adjustment mode.
Note:
For the setting procedure of the adjustment mode, refer to “4-1-5. Setting the Adjustment Mode” (Page 4-3).
2) Touch the Up, Down, Right or Left key to change selected item. Choose “Lens Option”, press the “Shutter” button to choose item.
Note:
If the setting is disabled, refer to “4-1-6. Enabling the Adjustment” to enable the setting. (Page 4-3)
3) Touch the Down key to “Enable LDC” item after touch the Right key to set enable (000001).
Touch the Down key to “Enable LSC” item after touch the Right key to set enable (000001).
Final Press the “Shutter” button to return to adjustment mode, then touch the Set key, select “OK” and touch the Set key to start.
Note:
LDC : Lens Distortion Correction
LSC : Lens Shading Correction
4) Confirm the indication on the screen.
When the setting is finished, the setting completion indication appears on the screen. (Fig. 4-3-20)
Press the “Shutter” button to return to adjustment menu.
LDC > ON
LSC > ON
Fig.
4-3-20
4-13
DSC-KW1/KW11
4-3-8. TP Adjustment
Update the firmware for TP control while checking the sensitivity of the TP.
TP Adjustment order is as follows.
1) Check that the camera is on the adjustment mode.
1) Check that the camera is on the adjustment mode.
Note:
• For the setting procedure of the adjustment mode, refer to “4-1-5. Setting the Adjustment Mode” (Page 4-3).
• Confirm that there is nothing to touch the surface of TP. (nothing including protection sheet or etc.)
• Confirm that there is nothing to touch the surface of TP. (nothing including protection sheet or etc.)
(Adjust it again if something touches the surface of TP by mistake.)
• Adjust it after the battery cover was closed.
2) Touch the Up, Down, Right or Left key to change selected item. Choose “UPDATE_TUPFW”, touch the Set key, select “OK”, and touch
the Set key to start. (Fig. 4-3-21)
X.XXXX
A0E6V3000033
Index : 01
TEST
X
BACKUP
RESTORE
UPDATE_TUPFW
UPDATE_TUPFW
OK
NO
Fig.
4-3-21
Note:
• Waiting time from start is about three minutes 30 seconds. (This means from start to end of update is about three minutes 30seconds.)
• When starting the update, message screen [Battery Low!!] is still appeared, replace a battery that capacity is enough.
• When starting the update, message screen [Battery Low!!] is still appeared, replace a battery that capacity is enough.
Battery Low!!
Please power off by power key
Fig.
4-3-22
4-14
DSC-KW1/KW11
3) Confirm the indication on the screen.
When the updating is finished, the updating completion indication appears on the screen. (Fig. 4-3-25)
Press the “Shutter” button to return to adjustment menu.
CurVersion:1004
NewVersion:1007
Upgrade TouchFW by Shutter key
Fig.
4-3-23
FW upgrading.
Fig.
4-3-24
The updating is complete.
FW upgrade Done
Please power off by power key
Fig.
4-3-25
4-15
DSC-KW1/KW11
Ver. 1.2 2014.11
4-3-9. Display WB Check/Calibration
This item is to check/calibrate the white balance of OLED panel within a predetermined range.
Item required:
• Gray chart files (DSC00001.JPG, DSC00002.JPG)
Preparations:
• Monitor Brightness in user menu: level 4 (default setting)
• Store the gray chart files to the [101MSDCF] folder in the [DCIM] folder of the Memory card.
• Store the gray chart files to the [101MSDCF] folder in the [DCIM] folder of the Memory card.
Checking order
1) Playback the gray chart files.
1) Playback the gray chart files.
2) Check that the display is not colored (reddish or bluish).
3) If not colored, this item is the end. If colored, proceed to the Calibration order.
Calibration order
1) Check that the camera is on the adjustment mode.
1) Check that the camera is on the adjustment mode.
Note:
For the setting procedure of the adjustment mode, refer to “4-1-5. Setting the Adjustment Mode” (Page 4-3).
2) Touch the Up, Down, Right or Left key to change selected item. Choose “TEST”, touch the Set key, and select “OK”. (Fig. 4-3-26)
And touch the Set key to switch the display to Fig. 4-3-27.
1.0000
A0E6V3000137
Index : 01
TEST
V
BACKUP
RESTORE
UPDATE_TUPFW
TEST
OK
NO
⇨
RGB Reset
NR
LCD R
000000
000000
000000
000020
000020
000020
LCD B
LCD G
AutoScenelcoNR
Fig. 4-3-26
Fig. 4-3-27
3) Change the value scales of “LCD_R (Fig.4-3-28)” and “LCD_B (Fig.4-3-29)” accordingly with using the Up, Down, Right or Left key.
Note:
The value scales can be changed from “000000” to “000040” (default “000020”).
Do not change the value “000020” of “LCD_G”.
RGB Reset
NR
LCD R
000000
000000
000000
000020
000020
000020
LCD B
LCD G
AutoScenelcoNR
⇨
RGB Reset
NR
LCD R
000000
000000
000000
000020
000020
000020
LCD B
LCD G
AutoScenelcoNR
Fig. 4-3-28
Fig. 4-3-29
4) After changing, press the “Shutter” button, then press the “ON/OFF (Power)” button to turn off the camera once.
5) Check that the display is not colored according to the above Checking order.
If colored, repeat the procedure from 1) to 4).
Click on the first or last page to see other DSC-KW1 / DSC-KW11 service manuals if exist.