DOWNLOAD Sony DSC-KW1 / DSC-KW11 Service Manual ↓ Size: 2.11 MB | Pages: 39 in PDF or view online for FREE

DSC-KW1/KW11

Note:
Be sure to keep your PC used for service and checking of this unit 
always updated with the latest version of your anti-virus software.
In case a virus affected unit was found during service, contact your 
Service Headquarters.

2014K08-1

  © 2014.11

Model

DSC-KW1

DSC-KW11

Destination

CH

KR, TW

E, HK

Color system

PAL

NTSC

PAL

GPS

–

–

–

Wi-Fi







NFC







•   Abbreviation 

 

 CH:  Chinese 

model 

  HK:  Hong Kong model 
 KR:  Korea 

model

 TW: Taiwan 

model

Photo: White

Revised-2

Replace the previously issued
SERVICE MANUAL 9-896-709-12
with this Manual.

– 1 –

DSC-KW1/KW11

0 OR DOTTED LINE WITH 

0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS 

0 SUR LES 

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.

This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with 

the lead free mark due to their particular size.)

Be careful to the following points to solder or unsolder.

•   Set the soldering iron tip temperature to 350 °C approximately. 

If cannot control temperature, solder/unsolder at high temperature 
for a short time.
Caution:  The printed pattern (copper foil) may peel away if the 

heated tip is applied for too long, so be careful!  

Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.

•   Be sure to control soldering iron tips used for unleaded solder and 

those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.

After correcting the original service problem, perform the following 

safety checks before releasing the set to the customer.

1.  Check the area of your repair for unsoldered or poorly-soldered 

connections. Check the entire board surface for solder splashes 
and bridges.

2.  Check the interboard wiring to ensure that no wires are “pinched” 

or contact high-wattage resistors.

3.  Look for unauthorized replacement parts, particularly transistors, 

that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.

4.  Look for parts which, through functioning, show obvious signs 

of deterioration. Point them out to the customer and recommend 
their replacement.

5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 

•   Set the soldering iron tip temperature to 350 °C approximately.

 

•   Do not touch the soldering iron on the same conductor of the 

circuit board (within 3 times).

 

•   Be careful not to apply force on the conductor when soldering 

or unsoldering.

注意

如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。

– 2 –

DSC-KW1/KW11

Image device:
 

7.87 mm (1/2.3 type) Exmor RS

 CMOS 

sensor

Total pixel number of camera:
 

Approx. 21.0 Megapixels

Effective pixel number of camera:
 

Approx. 19.2 Megapixels

Lens:
 

f = 21 mm (35 mm film equivalent)

 F2.0
 

While shooting movies (16:9):

 23 

mm

SteadyShot:
 Electronic
File format:
 

Still images: JPEG (DCF, Exif,

 

MPF Baseline) compliant, DPOF compatible

Movies (MP4 format):
 Video: 

MPEG-4 

AVC/H.264

 Audio: 

MPEG-4 

AAC-LC

Recording media:
 

Internal Memory (Approx. 28 MB), 

 

“Memory Stick Micro” media, 

 

microSD memory cards

Micro USB Terminal:
 USB 

communication

USB communication:
 

Hi-Speed USB (USB 2.0)

OLED:
 

Wide (16:9), 8.3 cm (3.3 type)

 TFT 

drive

Total number of dots:
 

1 229 760 dots

Power:
 

Rechargeable battery pack NP-

 BN, 

3.6 

V

 

AC Adaptor AC-UB10C, 5 V

Power consumption (during shooting):
 1.0 

W

Operating temperature:
 

0 °C to +40 °C

Storage temperature:
 

–20 °C to +60 °C

Dimensions (CIPA compliant):
 

57.7 mm × 125 mm × 20.1 mm

 (W/H/D)
Mass (CIPA compliant) (including
NP-BN battery pack, “Memory
Stick Micro” media):
 

Approx. 136 g

Microphone:
 Monaural
Speaker:
 Monaural
Exif Print:
 Compatible
PRINT Image Matching III:
 Compatible

Supported format:
 

IEEE 802.11 b/g/n

Model No. WW808162

Power requirements:
 

AC 100 V to 240 V, 50 Hz/60 Hz,

 70 

mA

Output voltage:
 

DC 5 V, 0.5 A

Operating temperature:
 

0 °C to 40 °C

Storage temperature:
 

–20 °C to +60 °C

Dimensions:
 

Approx. 50 mm × 22 mm × 54 mm (W/H/D)

Mass:
 

Approx. 48 g

Used battery:
 Lithium-ion 

battery

Maximum voltage:
 DC 

4.2 

V

Nominal voltage:
 DC 

3.6 

V

Maximum charge voltage:
 DC 

4.2 

V

Maximum charge current:
 0.9 

A

Capacity:
 

typical: 2.3 Wh (630 mAh)

 

minimum: 2.2 Wh (600 mAh)

Design and specifications are subject to change 
without notice.

DSC-KW1/KW11

1-1

NOTE:
•  Due to standardization, replacements in the parts list may be different from 

the parts specified in the diagrams or the components used on the set.

•  -XX, -X mean standardized parts, so they may have some differences from 

the original one.

•  Items marked “*” are not stocked since they are seldom required for routine 

service. Some delay should be anticipated when ordering these items.

• CAPACITORS:
 uF: 

μF

The components identified by mark 0 or dotted line with 

mark 0 are critical for safety.

Replace only with part number specified.
Les composants identifiés par une marque 0 sont 

critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro 
spécifié.

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.

注意

如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver) 

: Parts Color

• Abbreviation
  CH 

: Chinese model

  HK 

: Hong Kong model

 KR  : 

Korea 

model

 TW  : 

Taiwan 

model