Sony DSC-KW1 / DSC-KW11 Service Manual ▷ View online
DSC-KW1/KW11
3-2
3-2. OVERALL BLOCK DIAGRAM
GPIO I/F
27MHz
AUDIO I/F
Li-BATTERY
Code
Memory
Memory
FLASH MEM I/F
SD Memory
I/F
I/F
SPCA6350A
POWER Interface
POWER Interface
SYS_PLL
Stroge
DISPLAY I/F
GPIO I/F
SPCA6350A
32.768kHz
POWER CIRCUIT
(G2207)
(G2207)
Main Board
USB I/F
20 PIN
connector
Image Sensor
I/F
I/F
IU200F-Z
20 mega-pixel
CMOS Lens
module
20 mega-pixel
CMOS Lens
module
Microphone
Speaker
USB Connector
USB Plug DET
SD SOCKET
(COMBO CONN. 8191-3521-MD81)
(COMBO CONN. 8191-3521-MD81)
VIDEO I/F
RTC
WI-FI module(USI)
WIFI I/F
I2C
DDR3 2Gb K4B2G1646Q
128M*16 FBGA96
128M*16 FBGA96
NAND 1GK9F1G08U0D-SCB0
Charge IC
MAX14648
MAX14648
2 PIN
wire
solder
2 PIN
wire
solder
SENSOR BD
CHARGE CIRCUIT
(STOD03AS)
(STOD03AS)
Assistant
Exposure Light
BD
Exposure Light
BD
NFC
GPADC I/F
Battery Thermal
Detect
Detect
ANT
AMS326PM01 3.26"
Visual
WVGA(854×480)
Visual
WVGA(854×480)
61 PIN
Connector
G - sensor
Touch panel
6 PIN
Connector
Power key
& SNAP key
BD
& SNAP key
BD
6 PIN
Connector
6 PIN
Connector
Hinge switch BD
Coaxial
cable
cable
2 PIN
wire
solder
wire
solder
2 PIN
wire
solder
wire
solder
DSC-KW1/KW11
3-3
3-3. MAIN BLOCK
3-3-1. Rear Cover Section
• Disassembly order
No.
Part
Item
Note
1
Rear Cover Assy
Claw x 10
Slide open the Rear Cover Assy in the direction of arrow.
2
Rear Inner Assy
#S1 x 1, #S2 x 2, #S3 x 3,
#S5 x 3
#S5 x 3
3
Main Board and Chassis Assy
Solder x 14
Connector x 5
#S7 x 5
Connector x 5
#S7 x 5
4
Antenna
5
Top Cover Section
#S7
#S5
#S5
#S2
#S1
#S3
#S3
#S7
#S4 (Note)
#S7
(Claws)
(Claws)
(Claws)
(Connectors)
(Connectors)
(Solders)
(Solders)
(Solders)
(Solders)
1
2
3
4
5
Note :
This screw cannot be reused. Discard the screw
removed once in servicing. Instead, use a new
screw.
This screw cannot be reused. Discard the screw
removed once in servicing. Instead, use a new
screw.
DSC-KW1/KW11
3-4
3-3-2. Top Cover Section
• Disassembly order
No.
Part
Item
Note
1
NFC Flexible Board
Adhesive sheet
2
Display Bracket Assy
3
TP OLED Block Assy
(This order No. 3 can be
skipped if no need to replace it
with new part.)
skipped if no need to replace it
with new part.)
Adhesive sheet
As the TP-OLED Block Assy may be broken by slight pressure,
remove it by paying scrupulous attention.
remove it by paying scrupulous attention.
4
Lens Pink Cover/Lens Gold Cover
#S3 x 2
5
Lens Bottom Cover Assy
6
Top Cover Assy
7
Lens Holder Assy
#S7 x 2
8
CMOS Board Assy
#S7 x 1
Connector x 2
Connector x 2
9
Lens Assy
#S7 x 2
#S7
#S3
#S7
#S7
2
7
8
9
6
3
4
5
1
(Connector)
(Connector)
(Adhesive sheet)
(Adhesive sheet)
Procedure:
1 .Apply alcohol fully to all the periphery of the TP-OLED Block Assy.
2. Heat all the periphery of the TP-OLED Block Assy with Drier or etc..
3. To weaken the adhesiveness as much as possible,
soften the Adhesive sheet by repeating steps 1 and 2.
4. Push the TP-OLED Block Assy from the inside by slight power. If it does not
loosen, repeat steps 1 and 2.
5. After the TP-OLED Block Assy starts to loosen, apply alcohol more.
Push slightly slowly the TP-OLED Block Assy from the inside by slight power
again, and peel off the Adhesive sheet.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2014.10
DSC-KW1/KW11
3-5
3-4. COMPLEMENTARY INFORMATION
(1) Notes on Connecting the Coaxial Cable
Outside View
Inside View
CMOS Board Assy
Coaxial Cable
(2) Notes on Routing the Harness on AF Assist Light Board
Assy
AF Assist Light Board Assy
(3) Notes on Installing the Chassis Assy and Main Board
Assy
(1)
(2)
(Bosses)
(3)
(4)
(5)
(6)
(7)
1
2
3
4
Click on the first or last page to see other DSC-KW1 / DSC-KW11 service manuals if exist.