Sony STR-ZA1000ES / STR-ZA2000ES / STR-ZA3000ES Service Manual ▷ View online
STR-ZA1000ES/ZA2000ES/ZA3000ES
25
2-22. AMP BOARD BLOCK-1
3 Remove the wire
from the lead pin.
3 Remove the wire
from the lead pin.
1 Remove the wire
from the lead pin.
3 Remove the wires
from two lead pins.
A
B
B
A
(ZA3000ES)
4 connector
(CN550)
(CN550)
6 connector
(CN521)
(CN521)
2 connector
(CN901)
(CN901)
5 connector
(CN921)
(CN921)
3 Remove the wires
from two lead pins.
:LUHVHWWLQJ
AMP board
SPTM board
lead pin
lead pin
lead pin
lead pin
lead pin
lead pin
:LUHVHWWLQJ
lead pin
power transformer
(T01)
(T01)
AMP board
Brown wire is ZA3000ES only.
STR-ZA1000ES/ZA2000ES/ZA3000ES
26
2-23. AMP BOARD BLOCK-2
2 AMP board block
1 two screws
(BVTP3
(BVTP3
u 8)
1 two screws
(BVTP3
(BVTP3
u 8)
1 two screws
(BVTP3
(BVTP3
u 8)
1 screw
(BVTP3
(BVTP3
u 8)
1 screw
(BVTP3
(BVTP3
u 8)
STR-ZA1000ES/ZA2000ES/ZA3000ES
27
2-24. AMP BOARD
2-25. SPTM BOARD
2 two screws
(BVTP3
(BVTP3
u 8)
1 Remove forty-two
solders.
solders.
4 AMP board
3 heat sink block
– AMP board block rear view –
4 seven screws (BV/ring)
1 screw
(BVTP3
(BVTP3
u 8)
3 screw
(BVTP3
(BVTP3
u 8)
3 screw
(BVTP3
(BVTP3
u 8)
– Rear view –
5
Remove the SPTM
board in the direction
of an arrow.
6
SPTM board
SPTM board
A
A
1 Remove the wire
from two lead pins.
(See Fig. F)
2 connector
(CN951)
(CN951)
lead pin
power transformer (T01)
lead pin
:LUHVHWWLQJ
)LJ)!
STR-ZA1000ES/ZA2000ES/ZA3000ES
28
SECTION 3
TEST MODE
USER INITIALIZE (MEMORY CLEAR) MODE
All preset contents are cleared when this mode is activated.
(Sound fi eld is also cleared)
Use this mode before returning the product to clients upon comple-
tion of repair.
All preset contents are cleared when this mode is activated.
(Sound fi eld is also cleared)
Use this mode before returning the product to clients upon comple-
tion of repair.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn on the main power for fi ve sec-
onds.
2. The message “MEMORY CLEARING” appears and the mem-
ories are reset to the default values.
3. When done, the message “MEMORY CLEARED!” appears.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated.
Use this mode before returning the product to clients upon comple-
tion of repair.
(When USER INITIALIZE (MEMORY CLEAR) MODE or SHIP-
MENT MODE is performed, it is not necessary to perform the
SOUND FIELD CLEAR MODE)
The preset sound fi eld is cleared when this mode is activated.
Use this mode before returning the product to clients upon comple-
tion of repair.
(When USER INITIALIZE (MEMORY CLEAR) MODE or SHIP-
MENT MODE is performed, it is not necessary to perform the
SOUND FIELD CLEAR MODE)
Procedure:
1. While pressing the [MULTI ST.] button, press the [
1. While pressing the [MULTI ST.] button, press the [
?/1
] button
to turn on the main power.
2. The message “S.F. INITIALIZED!” appears and initialization
is performed.
SETTING LOCK MODE
All the settings can be locked.
All the settings can be locked.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn off the main power.
2. Press three buttons of the [PING], [AMP MENU] and [ENTER]
simultaneously.
3. The message “S. LOCK ON” appears.
Releasing method:
1. Press the [
1. Press the [
?/1
] button to turn off the main power.
2. Press three buttons of the [PING], [AMP MENU] and [ENTER]
simultaneously.
3. The message “S. LOCK OFF” appears.
COMMAND MODE MODE
The command mode of the remote-commander which this set re-
ceives can be changed.
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [2CH/A.DIRECT] button, press the [
1. While pressing the [2CH/A.DIRECT] button, press the [
?/1
]
button to turn on the main power.
2. Either the message “C. MODE AV1” or “C. MODE AV2” ap-
pears. Select the desired mode.
TUNER AM STEP CHANGE MODE
(US and Canadian models only)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
(US and Canadian models only)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. While pressing the [TUNING MODE] button, press the [
1. While pressing the [TUNING MODE] button, press the [
?/1
]
button to turn on the main power.
2. Either the message “AM 9k STEP” or “AM 10k STEP” ap-
pears, select the desired step.
USB UPDATE TEST MODE
This mode is guided by technical news, when update occurs.
This mode is guided by technical news, when update occurs.
USB UPDATE VERSION MODE
This mode is guided by technical news, when update occurs.
This mode is guided by technical news, when update occurs.
SWAP ALL MODE
The signal will be swap to all channel so that all speaker will have
sound output.
The signal will be swap to all channel so that all speaker will have
sound output.
Note: It is necessary to connect speakers to this unit.
Procedure:
1. While pressing the [MOVIE] and [MEMORY] buttons, press
1. While pressing the [MOVIE] and [MEMORY] buttons, press
the [
?/1
] button to turn on the main power.
2. The message “SWAP MODE” appears and sound from L and
R channel will swap to all channel.
3. Check that sound is outputted from all channel available based
on the speaker pattern setting.
Releasing method:
Press the [
Press the [
?/1
] button to turn off the main power.
Ver. 1.2
Click on the first or last page to see other STR-ZA1000ES / STR-ZA2000ES / STR-ZA3000ES service manuals if exist.