Sony STR-ZA1000ES / STR-ZA2000ES / STR-ZA3000ES Service Manual ▷ View online
MEMO
STR-ZA1000ES/ZA2000ES/ZA3000ES
7
STR-ZA1000ES/ZA2000ES/ZA3000ES
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2014.07
New
1.1
2014.11
Addition of STR-ZA1000ES
Change of DISPLAY, M_VOL, POWER_KEY, PRE-OUT and STBY boards (Suffi x-12)
(SMR-14028)
1.2
2015.04
Addition of Australian model (STR-ZA2000ES)
Deletion of Part for Ref. No. C8763 on the DIGITAL board
Change of M_VOL, POWER_KEY, PRE-OUT and STBY boards (Suffi x-13)
Change of DISPLAY boards (Suffi x-13) (SUPPLEMENT-1)
(SMR-14048)
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note:
If you still see the original page, press the [Enter] key again.
STR-ZA1000ES/ZA2000ES/ZA3000ES
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2014.07
New
1.1
2014.11
Addition of STR-ZA1000ES
Change of DISPLAY, M_VOL, POWER_KEY, PRE-OUT and STBY boards (Suffi x-12)
(SMR-14028)
1.2
2015.04
Addition of Australian model (STR-ZA2000ES)
Deletion of Part for Ref. No. C8763 on the DIGITAL board
Change of M_VOL, POWER_KEY, PRE-OUT and STBY boards (Suffi x-13)
Change of DISPLAY boards (Suffi x-13) (SUPPLEMENT-1)
(SMR-14048)
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note:
If you still see the original page, press the [Enter] key again.
STR-ZA1000ES/ZA2000ES/ZA3000ES
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2014.07
New
1.1
2014.11
Addition of STR-ZA1000ES
Change of DISPLAY, M_VOL, POWER_KEY, PRE-OUT and STBY boards (Suffi x-12)
(SMR-14028)
1.2
2015.04
Addition of Australian model (STR-ZA2000ES)
Deletion of Part for Ref. No. C8763 on the DIGITAL board
Change of M_VOL, POWER_KEY, PRE-OUT and STBY boards (Suffi x-13)
Change of DISPLAY boards (Suffi x-13) (SUPPLEMENT-1)
(SMR-14048)
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note:
If you still see the original page, press the [Enter] key again.