Sony STR-ZA1000ES / STR-ZA2000ES / STR-ZA3000ES Service Manual ▷ View online
STR-ZA1000ES/ZA2000ES/ZA3000ES
9
2-5. FRONT PANEL BLOCK-2
1 three screws
(BVTP3
(BVTP3
u 8)
2 saranet cushion
(LXWXT)
(LXWXT)
1 four screws
(BVTP3
(BVTP3
u 8)
1 three screws
(BVTP3
(BVTP3
u 8)
1 two screws
(BVTP3
(BVTP3
u 8)
lead pin
1 screw
(BVTP3
(BVTP3
u 8)
lead pin
4 front panel block
3 Draw the wires out of
the hole in chassis.
– Rear view –
– Front panel block rear view –
DISPLAY board
DISPLAY board
lead pin
DISPLAY board
HDMI cable
DISPLAY board
POWER_KEY board
POWER_KEY board
lead pin
lead pin
lead pin
lead pin
DISPLAY board
to DISPLAY
board
board
to DIGITAL board
flexible flat cable (FFC 29P (400))
long side
:ire VettinJ
(ZA2000ES/ZA3000ES)
(ZA1000ES)
(ZA2000ES/ZA3000ES)
saranet cushion (LXWXT)
:ire VettinJ
flexible flat cable (FFC 29P (400))
Ver. 1.1
STR-ZA1000ES/ZA2000ES/ZA3000ES
10
2-6. POWER UNIT BLOCK (ZA3000ES)
8 power unit block
7 hook
7 hook
:LUHVHWWLQJ
A
A
3 connector
(CN101)
(CN101)
2 connector
(CN601)
(CN601)
1 Remove the wire
from the clamp.
clamp
clamp
4 Remove the wire
from the clamp.
power unit
heat sink
power transformer
(T01)
(T01)
power unit
DIGITAL board
6
Remove the power unit
block in the direction of
an
arrow.
:LUHVHWWLQJ
5 four screws
(BVTP3
(BVTP3
u 8)
Note: The wire must not touch the heat sink
and the power transformer (T01).
STR-ZA1000ES/ZA2000ES/ZA3000ES
11
2-7. DIGITAL BOARD BLOCK-1
2 connector
(CN9001)
(CN9001)
4 connector
(CN1505)
(CN1505)
9 connector
(CN8005)
(CN8005)
qa connector
(CN8004)
(CN8004)
qd connector
(CN8001)
(CN8001)
0 connector
(CN1506)
(CN1506)
5 teflon tape (sub material)
teflon tape (sub material)
teflon tape (sub material)
5 teflon tape
(sub
(sub
material)
7 connector
(CN1502)
(CN1502)
– Rear view –
DIGITAL board
:LUHVHWWLQJ
DIGITAL board
DIGITAL board
6 Cut the cable tie.
cable tie
qf wire (flat type) (11 core)
(CN6000)
(CN6000)
:LUHVHWWLQJ
7HIORQWDSHVHWWLQJ
DIGITAL board
DC FAN
:LUHVHWWLQJ
clamp
1 Remove the wire from the clamp.
3 Remove the wire
from the clamp.
clamp
(ZA3000ES)
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note 2: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Note 1: During reassembly, use new cable ties
to fasten the wires back in place as
they were before disassembly.
qs flexible flat cable (FFC 29P (130)) (CN8006)
Note
Note
3:
Prevent the removed cable from touching
grease of heat sink.
heat sink
8 flexible flat cable (FFC 19P (130)) (CN8009)
Note
Note
3:
Prevent the removed cable from touching
grease of heat sink.
STR-ZA1000ES/ZA2000ES/ZA3000ES
12
2-8. DIGITAL BOARD BLOCK-2
2-9. DIGITAL BOARD
2 screw
(BV3
(BV3
u 8CU)
2 two screws
(BV3
(BV3
u 8CU)
3 seven screws
(B3
(B3
u 5)
5 DIGITAL board block
– Rear view –
4
Remove the DIGITAL board block
in the direction of an arrow.
1 screw
(BVTP3
(BVTP3
u 8)
1 screw
(BVTP3
(BVTP3
u 8)
3 boss
3 boss
4 bracket (4F digital) block
7 HDMI heat sink
8 radiation sheet
9 DIGITAL board
1 screw
(BV3
(BV3
u 8CU)
1 screw
(BV3
(BV3
u 8CU)
1 screw
(BV3
(BV3
u 8CU)
1 screw
(BV3
(BV3
u 8CU)
1 screw
(BV3
(BV3
u 8CU)
1 screw
(BV3
(BV3
u 8CU)
2 clamp
2 clamp
2 clamp
5 cover (indicator-rear) block
6 Bent two claws are returned
to a straight form.
(ZA3000ES)
Click on the first or last page to see other STR-ZA1000ES / STR-ZA2000ES / STR-ZA3000ES service manuals if exist.