Sony MHC-V6D Service Manual ▷ View online
MHC-V6D
9
2-3. TOP PANEL BLOCK
1 three screws
(BVTP3
(BVTP3
u 10)
4 cushion (H)
cushion (H)
heat sink
3 Remove the top panel block
in the direction of the arrow.
2 five claws
7 top panel block
Terminal face is
below side.
below side.
TOP KEY A board
WireVHWWLQJ
guide line
guide line
guide line
guide line
–7RSUHDUYLHZ–
Note 1: Fix the cushion (H) so that
the flexible flat cable does not
come in contact with the heat sink.
WireVHWWLQJ
Terminal face is
below side.
below side.
–7RSSDQHOEORFN
ERWWRPYLHZ–
ERWWRPYLHZ–
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note 2: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
5 flexible flat cable
(4P)
(4P)
(CN2102)
6 flexible flat cable
(15P)
(15P)
(CN2100)
flexible flat cable (15P)
flexible flat cable (4P)
MHC-V6D
10
2-4. VOLUME KNOB BLOCK
2 volume knob block
hole
1 Push the volume knob block
by flat-head screwdriver.
top panel block
volume knob block
rib
shaft
Note 1: When installing the volume knob block,
aline the two ribs of volume knob and
the
shaft.
+RZWRLQVWDOOWKHYROXPHNQREEORFN
±BRWWRPYLHZ–
–
7RSYLHZ–
Note 2: When installing the volume knob block,
please apply suncall (CFD-703Z) to rib
and shaft inside.
$SSOLFDWLRQSRVLWLRQRIVXQFDOO&)'=
rib
hole
TOP KEY B board
TOP KEY A board
shaft
–
BRWWRPYLHZ–
–
7RSSDQHOEORFNERWWRPYLHZ–
MHC-V6D
11
2-5. LOADING PANEL BLOCK
1 Insert the clip etc. in the hole,
and push the lever in the direction
of the arrow.
2 Draw out the tray.
tray
CD mechanism deck
thin wire (clip etc. )
–
Top view
–
–
Left view
–
hole
3 two
claws
claws
4 loading panel block
8 cm or more
hole
MHC-V6D
12
2-6. CDM BLOCK
3 Remove the CDM block
in the direction of the arrow.
5 flexible flat cable
(5P)
(5P)
(CN303)
6 flexible flat cable
(24P)
(24P)
(CN302)
7 CDM block
CDM block
WireVHWWLQJ
ARAGON board
–7RSUHDUYLHZ–
1 two screws
(BVTP3
(BVTP3
u 10)
2 two hooks
1 screw
(BVTP3
(BVTP3
u 10)
4 connector
(CN401)
(CN401)
1 screw
(BVTP3
(BVTP3
u 10)
Note 1: Connect the wire from the CDM
block to the ARAGON board and
place it neatly inside the CDM
block.
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note 2: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Note 3: Insert the connector straight into the interior.
There is a possibility that using this device without
the connector correctly installed will damage it.
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
Click on the first or last page to see other MHC-V6D service manuals if exist.