Sony MHC-V6D Service Manual ▷ View online
MHC-V6D
5
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.
• D-AMP
board
CN1000 (pin 6 and 10, pin 6 and 3)
•
Switching regulator (SWR1)
C202, C203, C403, C407, C531 and C532
– Switching Regulator (Conductor Side) –
– D-AMP Board (Conductor Side) –
800
:/2 W
(for C403)
800
:/2 W
(for C407)
800
:/2 W
(for C531)
800
:/2 W
(for C532)
800
:/2 W
(for C203)
800
:/2 W
(for C202)
800
:/2 W
(pin 3 and 6)
800
:/2 W
(pin 6 and 10)
1
10
CN1000
MODEL IDENTIFICATION
Distinguish by Part No. and Destination code on the rear side of
a main unit.
Distinguish by Part No. and Destination code on the rear side of
a main unit.
– Rear View –
– Back Panel –
Part No.
Destination code
Part No.
Destination code
Destination
4-488-633-0[]
E4/SA2
African and South African
4-488-633-1[]
E12
Indian
4-488-633-2[]
E51
Chilean and Peruvian
4-488-633-3[]
E93
United Arab Emirates,
Kuwait, Iraq, Kenya,
Tanzania and Nigeria
Kuwait, Iraq, Kenya,
Tanzania and Nigeria
4-488-633-4[]
SP6
Singapore and Malaysia
4-488-633-5[]
TH1
Thai
4-488-633-6[]
MX4
Mexican
4-488-633-7[]
E2
120V AC area in E
Ver. 1.3
MHC-V6D
6
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
Note 1: After the side panel and top panel are removed, this work is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
tray
CD mechanism deck
–
Top view
–
hole
8 cm or more
2 Draw out the tray.
1 Insert the clip etc. in the hole,
and push the lever in the direction
of the arrow.
thin wire (clip etc. )
–
Left view
–
hole
MHC-V6D
7
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. SIDE L, R PANEL BLOCK
(Page
(Page
8)
2-22. FL BOARD BLOCK
(Page
(Page
28)
2-3. TOP PANEL BLOCK
(Page
(Page
9)
2-5. LOADING PANEL BLOCK
(Page
(Page
11)
2-6. CDM
BLOCK
(Page
12)
2-4. VOLUME KNOB BLOCK
(Page
(Page
10)
2-7. BACK PANEL BLOCK
(Page
(Page
13)
2-8. ARAGON
BOARD-1
(Page
14)
2-10. ARAGON BOARD-3
(Page
(Page
16)
2-9. ARAGON
BOARD-2
(Page
15)
2-11. D-AMP BOARD-1
(Page
(Page
17)
2-12. D-AMP BOARD-2
(Page
(Page
18)
2-13. SUB CHASSIS
(Page
(Page
19)
2-14. FRONT PANEL BLOCK-1
(Page
(Page
20)
2-15. FRONT PANEL BLOCK-2
(Page
(Page
21)
2-16. SWITCHING REGULATOR
(SWR1)
(Page
(SWR1)
(Page
22)
2-23. BLUETOOTH MODULE
(BT1)
(Page
(BT1)
(Page
29)
2-24. USB BOARD BLOCK
(Page
(Page
30)
2-25. MIC BOARD
(Page
(Page
31)
2-26. NFC MODULE (NFC1)
(Page
(Page
31)
2-17. FRONT PANEL (SP) BLOCK
(Page
(Page
23)
2-18. SPEAKER LED BOARD,
FRONT PANEL (SP) ASSY
(Page
24)
2-19. LOUDSPEAKER (25 cm)
(WOOFER)
(WOOFER)
(SP5)
(Page
25)
2-20. LOUDSPEAKER (10 cm)
(MID: L-CH) (SP1)
(Page
26)
2-21. LOUDSPEAKER (10 cm)
(MID: R-CH) (SP3)
(Page
27)
2-27. FFC HOLDER
(Page
(Page
32)
2-28. OPTICAL PICK-UP BLOCK
(CMS-S76RFS7G)
(CMS-S76RFS7G)
(OP1)
(Page
33)
JIG
When disassembling the unit, use the following
jig for speaker removal.
When disassembling the unit, use the following
jig for speaker removal.
Part No.
Description
J-2501-238-A JIG FOR SPEAKER REMOVAL
MHC-V6D
8
Note: Follow the disassembly procedure in the numerical order given.
2-2. SIDE L, R PANEL BLOCK
6 side R panel block
4 three screws
(BVTP3
(BVTP3
u 10)
4 three screws
(BVTP3
(BVTP3
u 10)
5 Remove the side R panel block
in the direction of the arrow.
5 Remove the side L panel block
in the direction of the arrow.
4 three screws
(BVTP3
(BVTP3
u 10)
4 three screws
(BVTP3
(BVTP3
u 10)
6 side L panel block
2 claw
2 claw
3 screw cap
needle-nose pliers
needle-nose pliers
2 claw
2 claw
3 screw cap
1 Insert needle-nose pliers behind
the second fin, and press
in the direction of the arrow.
Note: Do not damage screw cap.
1 Insert needle-nose pliers behind
the second fin, and press
in the direction of the arrow.
Note: Do not damage screw cap.
Click on the first or last page to see other MHC-V6D service manuals if exist.