Sony MHC-V6D Service Manual ▷ View online
MHC-V6D
21
2-15. FRONT PANEL BLOCK-2
Note 1:
Pass the flexible flat cable (4P)
over the top of the loudspeaker.
Note 2: Insert the connector straight into the interior.
There is a possibility that using this device without
the connector correctly installed will damage it.
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
–
Top rear view
–
6 front panel block
[yellow]
[black]
[blue]
[black]
:LUHVHWWLQJ
:LUHVHWWLQJ
1
terminal
(narrow
side)
[blue]
5
two bosses
5
boss
5
boss
2
terminal
(narrow
side)
[yellow]
1
terminal
(wide
side)
[black]
2
terminal
(wide
side)
[black]
3
connector
(CN2002)
C
C
4 three screws
(BV/RING)
(BV/RING)
MIC board
MHC-V6D
22
2-16. SWITCHING REGULATOR (SWR1)
5 two screws
(BV/RING)
(BV/RING)
7 switching regulator
(SWR1)
(SWR1)
–
Top rear view
–
5 screw
(BV/RING)
(BV/RING)
6 coating clip
5 two screws
(BV/RING)
(BV/RING)
5 three screws
(BV/RING)
(BV/RING)
4 connector
(CN201)
(CN201)
3 connector
(CN401)
(CN401)
2 connector
(CN101)
(CN101)
Note: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
OK
NG
NG
1 Remove the wire from
the coating clip.
:LUHVHWWLQJ
switching regulator
(SWR1)
(SWR1)
coating clip
MHC-V6D
23
2-17. FRONT PANEL (SP) BLOCK
5 Remove the front panel (SP) block
in the direction of the arrow.
6 front panel (SP) block
total nineteen bosses
1 screw cushion
4 All bosses are removed while moving
jig in the direction of the arrow, and
front panel (SP) block is removed.
4 All bosses are removed while moving
jig in the direction of the arrow, and
front panel (SP) block is removed.
3 Insert the jig into the space and slowly
remove the front panel (SP) block.
Note: When using a jig, please work
so as not to injure front panel (SP)
block and speaker cabinet.
2 two tapping screws
(3.5
(3.5
u 14)
3 Insert the jig into the space and slowly
remove the front panel (SP) block.
Note: When using a jig, please work
so as not to injure front panel (SP)
block and speaker cabinet.
MHC-V6D
24
2-18. SPEAKER LED BOARD, FRONT PANEL (SP) ASSY
Note: Insert the connector straight into the interior.
There is a possibility that using this device without
the connector correctly installed will damage it.
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
4 SPEAKER LED board
–
Front panel (SP) assy rear view
–
:LUHVHWWLQJ
3 connector
(CN1800)
(CN1800)
1 cushion (H)
1 cushion (H)
6OHHYHIHUULWHFODPS)&VHWWLQJ
cushion
(E 0.5)
(E 0.5)
sleeve ferrite clamp
(FC5)
(FC5)
2 screw
(BVTP3
(BVTP3
u 8)
5 front panel (SP) assy
Wrap twice.
SPEAKER LED board
cushion (H)
total six grooves
cushion (H)
Click on the first or last page to see other MHC-V6D service manuals if exist.