Sony MHC-V6D Service Manual ▷ View online
MHC-V6D
29
2-23. BLUETOOTH MODULE (BT1)
filament tape
(sub material)
(sub material)
3 filament tape
(sub
(sub
material)
5 bluetooth module
(BT1)
(BT1)
bluetooth module
(BT1)
(BT1)
1 cishion (H)
bluetooth module
(BT1)
(BT1)
cushion (H)
WireVeWWiQJ
WireVeWWiQJ
+RZWRiQVWDOOWKeEOXeWRRWKPRGXOe%7
to
bluetooth
module
(BT1)
bluetooth
module
(BT1)
OK
NG
Terminal face is
below side.
below side.
terminal face
bluetooth module
(BT1)
(BT1)
bluetooth module
(BT1)
(BT1)
2 Remove the bluetooth
module (BT1) in the
direction of the arrow.
–
)rRQWSDQeOreDrYieZ–
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
4 flexible flat cable (10P)
(FFC7)
(FFC7)
flexible flat cable (10P)
(FFC7)
(FFC7)
MHC-V6D
30
2-24. USB BOARD BLOCK
• Abbreviation
E93: United Arab Emirates, Kuwait, Iraq, Kenya, Tanzania and Nigeria models
E93: United Arab Emirates, Kuwait, Iraq, Kenya, Tanzania and Nigeria models
3 Remove the USB board block
in the direction of the arrow.
to USB board
terminal
face
face
– Front panel rear view –
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
5 flexible flat cable
(4P)
(CN2202)
(4P)
(CN2202)
2 coating clip
1 screw
(BVTP3
(BVTP3
u 8)
1 two screws
(BVTP3
(BVTP3
u 8)
(E93)
6 USB board block
1 three screws
(BVTP3
(BVTP3
u 8)
Ferrite Fore (F&3) VettinJ
filament tape
(sub material)
(sub material)
USB board
Wire VettinJ
cushion (E 0.5)
Wrap once.
ferrite core (FC3)
guide line
4 filament tape
(sub
(sub
material)
MHC-V6D
31
2-25. MIC BOARD
2-26. NFC MODULE (NFC1)
– Front panel rear view –
2 screw
(BVTP3
(BVTP3
u 8)
1 knob
(MIC)
(MIC)
3 MIC board
2 screw
(BVTP3
(BVTP3
u 8)
2 Peel off the adhesive sheet (NFC).
6 Peel off the
tape
tape
(NFC).
3 Remove the NFC module block
in the direction of the arrow.
WireVeWWiQJ
OK
NG
Terminal face is
below side.
below side.
terminal face
to
NFC module
(NFC1)
NFC module
(NFC1)
–
)rRQWSDQeOreDrYieZ–
4 filament tape
(sub
(sub
material)
8 NFC module
(NFC1)
(NFC1)
7 NFC holder
1 screw
(BVTP3
(BVTP3
u 8)
NFC module
block
block
WireVeWWiQJ
filament tape
(sub material)
(sub material)
NFC module block
NFC module
block
block
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
5 flexible flat cable (8P)
(FFC6)
(FFC6)
flexible flat cable (8P)
(FFC6)
(FFC6)
MHC-V6D
32
2-27. FFC HOLDER
cushion (H)
FFC holder
3 cushion (H)
boss
boss
claw
5 Draw out the flexible flat
cable (24P) from hole.
4 Remove the
FFC
FFC
holder
in the direction
of the arrow.
– CD mechanism deck block bottom view –
6 FFC holder
Note: When installing the FFC holder,
Note: When installing the FFC holder,
check that installed firmly
two bosses and claw.
hole
+RZWRLQVWDOOWKH))&KROGHU
3DVWLQJSRVLWLRQRIFXVKLRQ+
There is a gap.
There is no gap.
OK
NG
–Bottom view –
1 two screws
(BVTP3
(BVTP3
u 8)
2 CD mechanism deck block
1 two screws
(BVTP3
(BVTP3
u 8)
Click on the first or last page to see other MHC-V6D service manuals if exist.