Sony MHC-V6D Service Manual ▷ View online
MHC-V6D
33
2-28. OPTICAL PICK-UP BLOCK (CMS-S76RFS7G) (OP1)
5 insulator
screw
screw
5 insulator screw
5 insulator
screw
screw
5 insulator screw
8 flexible flat cable (24P)
(FFC1)
(FFC1)
9 connector
7 connector
0 insulator
0 insulator
0 insulator
0 insulator
qa optical pick-up block
(CMS-S76RFS7G)
(OP1)
(CMS-S76RFS7G)
(OP1)
6 Remove the optical pick-up block
in the direction of the arrow.
4 three
claws
claws
WireVeWWiQJ
)Oe[iEOeIODWFDEOe3VeWWiQJ
1 claw
1 claw
1 claw
1 two
claws
claws
1 claw
2 chuck holder block
±BRWWRPYieZ–
Terminal face is below side.
–
7RSYieZ–
3 Draw out the tray.
Note
Note
3: When you can not draw out the tray,
please refer to “HOW TO OPEN THE TRAY
WHEN POWER SWITCH TURN OFF” on page 6.
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note 1: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Note 2: Insert the connector straight into the interior.
There is a possibility that using this device without
the connector correctly installed will damage it.
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
MHC-V6D
34
SECTION 3
TEST MODE
COLD RESET
It can clears all data including preset data stored in the memory to
initial conditions. Execute this mode when returning the this unit
to the customer.
It can clears all data including preset data stored in the memory to
initial conditions. Execute this mode when returning the this unit
to the customer.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press two buttons of the [
x
] and [PAN] simultaneously for
three seconds.
3. The
message “COLD RESET” is displayed on the fl uorescent
indicator tube, then becomes the standby state.
Screen display
USER RESET
It can clears all data including preset data stored in the memory
to initial conditions (Only the connection history information of
Bluetooth is not initialized).
It can clears all data including preset data stored in the memory
to initial conditions (Only the connection history information of
Bluetooth is not initialized).
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press two buttons of the [
x
] and [BASS BAZUCA] simultane-
ously for three seconds.
3. The message “RESET” is displayed on the fl uorescent indica-
tor tube, then becomes the standby state.
Screen display
AM TUNER STEP CHANGE
It can change AM step interval into 9 kHz or 10 kHz.
It can change AM step interval into 9 kHz or 10 kHz.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the AM function.
3. Press the [
3. Press the [
?/1
] button to turn the power off.
4. While
pressing
the
[
>
TUNING+] button, press the [
?/1
]
button.
5. The message “9K STEP” or “10K STEP” is displayed on the
fl uorescent indicator tube, and AM step interval changed.
Screen display
or
DISC TRAY LOCK MODE
It can be unable to take sample disc out of disc tray in the shop.
It can be unable to take sample disc out of disc tray in the shop.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the DVD/CD function.
3. Press the [
3. Press the [
Z
] button to open the disc tray and set the disc.
4. Press the [
Z
] button to close the disc tray.
5. Press two buttons of the [
x
] and [ENTER] simultaneously for
three seconds.
6. The message “LOCKED” is displayed on the fl uorescent indi-
cator tube and the disc tray is locked.
(Even if pressing the [
Z
] button, the message “LOCKED” is
displayed on the fl uorescent indicator tube and the disc tray is
locked)
locked)
Screen display
Releasing method:
1. Press two buttons of the [
1. Press two buttons of the [
x
] and [ENTER] simultaneously for
three seconds.
2. The message “UNLOCKED” is displayed on the fl uorescent
indicator tube and the disc tray is unlocked.
Bluetooth PAIRING HISTORY CLEAR
It can clear the Bluetooth pairing history.
It can clear the Bluetooth pairing history.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the Bluetooth function.
3. Press two buttons of the [
3. Press two buttons of the [
x
] and [FLANGER] simultaneously
for three seconds.
4. The message “BT HISTORY”
→ “CLEAR” is displayed on
the fl uorescent indicator tube, and the pairing history of Blue-
tooth is cleared.
tooth is cleared.
Screen display
MHC-V6D
35
VERSION DISPLAY
It can confi rm the SC and MTK version.
It can confi rm the SC and MTK version.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press two buttons of the [ENTER] and [MOVIE/GAME] si-
multaneously for three seconds.
3. The SC and MTK version is displayed on the fl uorescent indi-
cator tube, and it returns to the display of the normal mode.
SC version
MTK version
(Displayed values in the above fi gure are example)
PANEL TEST
It can confi rm the fl uorescent indicator tube, LEDs, model name,
destination, software version and button.
It can confi rm the fl uorescent indicator tube, LEDs, model name,
destination, software version and button.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press two buttons of the [ENTER] and [FOOTBALL] simulta-
neously for three seconds.
3. It enters the panel test mode, and all segments on the fl uores-
cent indicator tube and all LEDs light up.
Screen display
1
NX
REC
cPLAYc
REC
FLDR SHUF
1 USB PGM
ALL USB SEARCH
USB B
VIDEO
PHOTO
MUSIC
TUNED
MONO
AUTO
USB A
%
NTSC
SLEEP
PRESET
STEREO
4. Each time the [ENTER] button is pressed, the screen display is
changed in order as follows.
All segments and
all LEDs turn on
Speaker illumination:
white
all LEDs turn on
Speaker illumination:
white
All segments and
all LEDs turn on
Speaker illumination:
blue
all LEDs turn on
Speaker illumination:
blue
All segments and
all LEDs turn off
Speaker illumination:
off
all LEDs turn off
Speaker illumination:
off
Test pattern 1
Speaker illumination:
red
Speaker illumination:
red
Test pattern 2
Speaker illumination:
green
Speaker illumination:
green
1
REC
cPLAY
SHUF
1 USB
USB
USB B
VIDEO
PHOTO
MUSIC
MONO
AUTO
%
1
NX
REC
cPLAYc
REC
FLDR SHUF
1 USB PGM
ALL USB SEARCH
USB B
VIDEO
PHOTO
MUSIC
TUNED
MONO
AUTO
USB A
%
NTSC
SLEEP
PRESET
STEREO
c
REC
FLDR
PGM
ALL
SEARCH
TUNED
USB A
NTSC
SLEEP
PRESET
STEREO
1
NX
REC
cPLAYc
REC
FLDR SHUF
1 USB PGM
ALL USB SEARCH
USB B
VIDEO
PHOTO
MUSIC
TUNED
MONO
AUTO
USB A
%
NTSC
SLEEP
PRESET
STEREO
5. When
pressing
the
[ +PRESET+] button, the model name is
displayed on the fl uorescent indicator tube.
Screen display
6. Each time [ +PRESET+] button is pressed, tthe display
changes destination
→ SC version → MTK version → OPU
version
→ UI version → PF version → SYS version → CD
version
→ CMA version → CMB version → ST version →
TA version
→ TM version this order, and returns to the model
name display.
Model name
Destination
SC version
MTK version
OPU version
UI version
PF version
SYS version
CD version
CMA version
CMB version
ST version
TA version
TM version
(Displayed values in the above fi gure are example)
Destination
Display
120V AC area in E model (E2)
LATIN
African model (E4)
EA3-2
Indian model (E12)
E12
Chilean and Peruvian models (E51)
LATIN
United Arab Emirates, Kuwait, Iraq, Kenya,
Tanzania and Nigeria models (E93)
Tanzania and Nigeria models (E93)
EA3-2
South African model (SA2)
EA3-2
Mexican model (MX4)
MX
Singapore and Malaysia models (SP6)
ASIA-2
Thai model (TH1)
ASIA-2
7. When
pressing
the
[
x
] button while the each version is dis-
played, month and day of the software creation is displayed.
When pressing the [
When pressing the [
x
] button again, the display returns to the
each version display.
Screen display
(Displayed values in the above fi gure are example)
– Continued on next page –
Ver. 1.3
MHC-V6D
36
8. When pressing the [ –PRESET–] button, “K 0 V0” is dis-
played on the fl uorescent indicator tube.
Screen display
9. Each time a button is pressed, “K 0” value increases. However,
once a button is pressed, it is no longer taken into account.
When pressing the all buttons, “K22” and “OK” are displayed
alternately
alternately
Screen display
10. “V0” value increases “V1”, “V2”, “V3” · · · “V8”, “V9”, “V0”
if turn the [VOLUME/DJ CONTROL] knob clockwise, or it
decreases “V9”, “V8”, “V7” · · · “V2”, “V1”, “V0” if turn the
knob counterclockwise.
decreases “V9”, “V8”, “V7” · · · “V2”, “V1”, “V0” if turn the
knob counterclockwise.
Releasing method:
Press two buttons of the [ENTER] and [FOOTBALL] simultane-
ously for three seconds.
Press two buttons of the [ENTER] and [FOOTBALL] simultane-
ously for three seconds.
DVD COLOR SYSTEM CHANGE
It can change DVD color system into NTSC or PAL.
It can change DVD color system into NTSC or PAL.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the DVD/CD function.
3. Press two buttons of the [PAN] and [LED COLOR] simultane-
3. Press two buttons of the [PAN] and [LED COLOR] simultane-
ously for three seconds.
4. The message “COLOR NTSC” or “COLOR PAL”is displayed
on the fl uorescent indicator tube, and DVD color system
changed.
changed.
Screen display
or
5. When the “NTSC” mark is lights up, DVD color system is
NTSC.
When the “NTSC” mark is turns off, DVD color system is
PAL.
PAL.
Screen display
MUSIC
NTSC
(Displayed characters in the above fi gure are example)
DVD SERVICE MODE
• This mode let you make diagnosis and adjustment easily by
• This mode let you make diagnosis and adjustment easily by
using the remote commander and the TV. The instructions, di-
agnostic results, etc. are given on the on-screen display.
agnostic results, etc. are given on the on-screen display.
• TEST DISC LIST
Be sure to use the DVD disc that matches the signal standards
of your region.
• For CD
of your region.
• For CD
Part No.
Description
3-702-101-01 DISC
(YEDS-18),
TEST
4-225-203-01 DISC
(PATD-012),
TEST
J-2501-307-A DISC
(HLX-A1),
TEST
• For DVD SL (Single Layer)
Part No.
Description
J-6090-069-A
DISC (HLX-503), TEST (NTSC)
J-6090-088-A
DISC (HLX-504), TEST (NTSC)
J-6090-077-A
DISC (HLX-506), TEST (PAL)
• For DVD DL (Double Layer)
Part No.
Description
J-6090-071-A
DISC (HLX-501), TEST (NTSC)
J-6090-089-A
DISC (HLX-505), TEST (NTSC)
J-6090-078-A
DISC (HLX-507), TEST (PAL)
• Procedure to enter to DVD Service Mode:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the DVD/CD function.
3. Press two buttons of the [WAH] and [LED COLOR] simulta-
3. Press two buttons of the [WAH] and [LED COLOR] simulta-
neously for three seconds.
4. The message “SERVICE IN” appears on the fl uorescent in-
dicator tube and the Top Menu of Remocon Diagnosis Menu
appears on the on-screen display on the TV. The model name,
main unit’s micom version information (IF-con) and DVD
fi rmware version information (Syscon) are displayed at the
bottom of the on-screen display.
appears on the on-screen display on the TV. The model name,
main unit’s micom version information (IF-con) and DVD
fi rmware version information (Syscon) are displayed at the
bottom of the on-screen display.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
Model Name : V6D_GA
IF
IF
–con : Ver. 01.02 (0000)
Syscon : Ver. 1.020
5. To execute each function, press its number by using numeric
button on the remote commander.
Releasing method:
Press the [
Press the [
?/1
] button to turn the power off.
Click on the first or last page to see other MHC-V6D service manuals if exist.