Sony HBD-NF7220 Service Manual ▷ View online
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
HBD-NF7220
121
< RESISTOR >
R2700 1-218-990-81 SHORT
CHIP 0
R2701 1-218-953-11 METAL
CHIP 1K
5% 1/16W
R2702 1-218-941-81 METAL
CHIP 100
5% 1/16W
R2703 1-218-941-81 METAL
CHIP 100
5% 1/16W
R2704 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2705 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2706 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2707 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2708 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2709 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2710 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2711 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2713 1-218-990-81 SHORT
CHIP 0
R2715 1-218-957-11 METAL
CHIP 2.2K
5% 1/16W
R2717 1-218-957-11 METAL
CHIP 2.2K
5% 1/16W
R2718 1-218-990-81 SHORT
CHIP 0
R2719 1-218-990-81 SHORT
CHIP 0
R2720 1-218-990-81 SHORT
CHIP 0
R2721 1-218-990-81 SHORT
CHIP 0
R2734 1-218-957-11 METAL
CHIP 2.2K
5% 1/16W
R2736 1-216-821-11 METAL
CHIP 1K
5% 1/10W
R2737 1-216-821-11 METAL
CHIP 1K
5% 1/10W
R2738 1-216-821-11 METAL
CHIP 1K
5% 1/10W
R2739 1-216-821-11 METAL
CHIP 1K
5% 1/10W
R2740 1-216-821-11 METAL
CHIP 1K
5% 1/10W
R2741 1-216-821-11 METAL
CHIP 1K
5% 1/10W
R2746 1-218-945-11 METAL
CHIP 220
5% 1/16W
R2747 1-218-945-11 METAL
CHIP 220
5% 1/16W
R2748 1-218-945-11 METAL
CHIP 220
5% 1/16W
*************************************************************
A-1978-581-A TOUCH_S BOARD, COMPLETE
************************
< CAPACITOR >
C2953 1-117-728-81 CERAMIC
CHIP 1PF
0.1PF 16V
C2954 1-116-737-11 CERAMIC
CHIP 1uF
20% 10V
C2955 1-116-737-11 CERAMIC
CHIP 1uF
20% 10V
* C2956 1-116-720-11 CERAMIC CHIP 10uF
20%
6.3V
C2957 1-118-386-11 CERAMIC
CHIP 0.1uF
10% 16V
C2958 1-116-737-11 CERAMIC
CHIP 1uF
20% 10V
C2961 1-118-386-11 CERAMIC
CHIP 0.1uF
10% 16V
C2962 1-117-728-81 CERAMIC
CHIP 1PF
0.1PF 16V
C2964 1-117-728-81 CERAMIC
CHIP 1PF
0.1PF 16V
< CONNECTOR >
CN2964 1-794-235-51 CONNECTOR, FFC/FPC 11P
< DIODE >
D2950
6-502-993-01 DI SL-270S-WS-SD-TS
D2951
6-502-993-01 DI SL-270S-WS-SD-TS
D2952
6-502-993-01 DI SL-270S-WS-SD-TS
< IC >
IC2950
6-719-198-01 IC MM3411A33URE
IC2951
(Not supplied) IC LDS6204NTGI8
<
TRANSISTOR
>
Q2950 6-552-941-01 TR
LTC023JUBFS8TL
< RESISTOR >
R2950 1-218-941-81 METAL
CHIP 100
5% 1/16W
R2951 1-218-941-81 METAL
CHIP 100
5% 1/16W
R2952 1-250-616-11 METAL
CHIP 1K
1% 1/10W
R2953 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2954 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2955 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2956 1-250-618-11 METAL
CHIP 1.2K
1% 1/10W
R2957 1-218-990-81 SHORT
CHIP 0
R2958 1-218-953-11 METAL
CHIP 1K
5% 1/16W
R2959 1-218-990-81 SHORT
CHIP 0
R2960 1-218-957-11 METAL
CHIP 2.2K
5% 1/16W
R2961 1-218-957-11 METAL
CHIP 2.2K
5% 1/16W
R2965 1-218-990-81 SHORT
CHIP 0
R2966 1-218-990-81 SHORT
CHIP 0
R2967 1-218-990-81 SHORT
CHIP 0
R2971 1-250-616-11 METAL
CHIP 1K
1% 1/10W
R2972 1-218-957-11 METAL
CHIP 2.2K
5% 1/16W
*************************************************************
MISCELLANEOUS
**************
53
1-828-260-61 WIRE (FLAT TYPE) (26 CORE)
54
1-848-230-61 WIRE (FLAT TYPE) (11 CORE)
56
1-848-134-61 FLEXIBLE FLAT CABLE (8 CORE)
60
8-989-470-05 RC-S801/A5
(WW)
102
A-1977-315-A LOADING
ASSY
105
1-848-088-61 WIRE (FLAT TYPE) (5 CORE)
156
1-848-090-71 FLEXIBLE FLAT CABLE (45 CORE)
157
1-848-089-61 WIRE (FLAT TYPE) (9 CORE)
253
1-458-765-11 CARD WLAN/BT COMBO
255
1-828-273-61 WIRE (FLAT TYPE) (28 CORE)
258
1-970-007-11 HARNESS
(USB)
301
1-848-229-61 WIRE (FLAT TYPE) (15 CORE)
302
1-848-227-61 WIRE (FLAT TYPE) (5 CORE)
0 306
1-855-032-11 FAN, D.C.
0 308
1-834-966-41 POWER-SUPPLY CORD
0 354
1-474-546-11 SWITCHING REGULATOR (3L402W-1)
356
1-848-232-61 FLEXIBLE FLAT CABLE (24 CORE)
0 OP1
8-820-465-06 DEVICE, OPTICAL KEM480AHA/C2RP1
TOUCH_F
TOUCH_S
Note 3: When the WLAN/BT combo card is replaced, “NOTE
OF REPLACING THE WLAN/BT COMBO CARD AND
THE COMPLETE MB1305 BOARD” on page 6 and
“CHECKING METHOD OF NETWORK OPERATION” on
page 11.
THE COMPLETE MB1305 BOARD” on page 6 and
“CHECKING METHOD OF NETWORK OPERATION” on
page 11.
Note 1: IC2951 on the TOUCH_S board cannot exchange
with single. When this part on the TOUCH_S board is
damaged, exchange the entire mounted board.
damaged, exchange the entire mounted board.
Note 2: Flexible fl at cable and wires (fl at type) for service is all
straight.
Please bend it referring go “HOW TO BEND FFC” on
page 31 when you install it in the unit.
page 31 when you install it in the unit.
Note 4: When the device optical KEM480AHA/C2RP1 (OP1)
is replaced, refer to “NOTE OF REPLACING THE
OPTICAL DEVICE KEM480AHA/C2RP1 (OP1) AND
THE COMPLETE MB1305 BOARD” on page 7.
OPTICAL DEVICE KEM480AHA/C2RP1 (OP1) AND
THE COMPLETE MB1305 BOARD” on page 7.
HBD-NF7220
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2014.04
New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.
HBD-NF7220
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2014.04
New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.
HBD-NF7220
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2014.04
New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.