Sony HBD-N5200W / HBD-N7200W / HBD-N7200WL / HBD-N9200W / HBD-N9200WL Service Manual ▷ View online
HBD-N5200W/N7200W/N7200WL/N9200W/N9200WL
29
2-18. MB1305 BOARD
Note 1: When the complete MB1305 board is replaced, refer to “NOTE OF REPLACING THE WLAN/BT COMBO CARD AND
THE COMPLETE MB1305 BOARD” on page 8, “NOTE OF REPLACING THE OPTICAL DEVICE KEM480AHA/C2RP1
(OP1) AND THE COMPLETE MB1305 BOARD” on page 9 and “CHECKING METHOD OF NETWORK OPERATION”
on page 12.
(OP1) AND THE COMPLETE MB1305 BOARD” on page 9 and “CHECKING METHOD OF NETWORK OPERATION”
on page 12.
1 one screw
(+BV3
(+BV3
(3-CR))
2 ground plate (MB)
1 two screws
(+BV3
(+BV3
(3-CR))
7 three screws
(+B 3
(+B 3
u 3)
8 MB1305 board
3 heat sink (MB)
4 flexible flat cable (24 core)
(CN703)
(CN703)
5 CN301 (3P)
6 CN300 (8P)
colored line
colored line
Inserting is straight to the interior.
Inserting is slant.
connector
connector
OK
NG
Note 2: When installing the flexible flat cable,
ensure the colored line.
No slanting after insertion.
flexible flat cable
flexible flat cable
:LUHVHWWLQJ
CARD WLAN/
BT COMBO
BT COMBO
HBD-N5200W/N7200W/N7200WL/N9200W/N9200WL
30
2-19. DC FAN
2-20. POWER CORD
1 two screws
(+BV3
(+BV3
(3-CR))
2 fan, D.C.
The label side is the chassis side.
fan, D.C.
Note: When installing the fan, D.C.,
check that label side is the
chassis
side.
FBS 001
6 cord, power
50 + 5 mm
type No.
type No.
claw
cord, power
cord, power
FBS 001
4 claw
bushing (FBS001),
cord
cord
bushing
(FBS001), cord
(FBS001), cord
3 Remove the bushing
(FBS001), cord in the
direction of an arrow.
2 two claws
claw
%XVKLQJ)%6FRUGVHWWLQJ
3RZHUFRUGVHWWLQJ
Note: When installing the bushing (FBS001),
cord, mind the direction of claw at type
No. mark and align into the hole and
press in fully.
1 CN1 (2P)
5 bushing (FBS001),
cord
cord
power cord
switching regulator
push
HBD-N5200W/N7200W/N7200WL/N9200W/N9200WL
31
2-21. AMP BOARD
Note 1: When the complete AMP board is replaced, spread the compound refer-
ring to “NOTE OF REPLACING THE IC3101 AND IC3102 ON THE AMP
BOARD AND THE COMPLETE AMP BOARD” on page 6.
BOARD AND THE COMPLETE AMP BOARD” on page 6.
1 one screw
(+BV3
(+BV3
(3-CR))
7 four screws
(+BV3
(+BV3
(3-CR))
9 three screws
(+BVTP
(+BVTP
3
u 8)
0 heat sink
(AMP)
(AMP)
qa AMP board
2 two screws
(+BV3
(+BV3
(3-CR))
8 one screw
(+BV3
(+BV3
(3-CR))
3 shield (AMP)
4 CN101 (4P)
5 CN4 (3P)
6 flexible flat cable (24 core)
(CN3505)
(CN3505)
H
H
Note 2: When installing the flexible flat cable, ensure the colored line.
No slanting after insertion.
colored line
colored line
Inserting is straight to the interior.
Inserting is slant.
connector
connector
OK
NG
flexible flat cable
flexible flat cable
switching regulator
heat sink (AMP)
AMP board
WireVHWWLQJ
Ver. 1.2
HBD-N5200W/N7200W/N7200WL/N9200W/N9200WL
32
2-22. SWITCHING REGULATOR
1 three screws
(+BV3
(+BV3
(3-CR))
1 two screws
(+BV3
(+BV3
(3-CR))
4 switching regulator
3 insulator (bottom)
2 claw
Click on the first or last page to see other HBD-N5200W / HBD-N7200W / HBD-N7200WL / HBD-N9200W / HBD-N9200WL service manuals if exist.