DOWNLOAD Sony HBD-N5200W / HBD-N7200W / HBD-N7200WL / HBD-N9200W / HBD-N9200WL Service Manual ↓ Size: 13.7 MB | Pages: 127 in PDF or view online for FREE

The password will be supplied to only service HQ, and 
service center name, q’ty and all of software registered 
information should be maintained by service HQ, and 
Audio will ask to report the registration information.

Optical device KEM480AHA/C2RP1 (OP1) for BD requires pre-
cise read out functions and secure contents protection system for 
more than past DVD/CD.
Therefore, in the case repaired as follows, the writing work of the 
OP data is necessary.

•  When the optical device KEM480AHA/C2RP1 (OP1) is 

replaced (The complete MB1305 board doesn’t replace).

•  When both the optical device KEM480AHA/C2RP1 (OP1) 

and complete MB1305 board are replaced.

•  When the complete MB1305 board is replaced (The optical 

device KEM480AHA/C2RP1 (OP1) doesn’t replace)

 

(In this case, do the work of “3. Optical device KEM480AHA/
C2RP1 (OP1) replacement” other than the replacement of new 
optical device).

Note: The servo adjustment is done while writing the OP data. The manual 

adjustment is unnecessary.

 

  LD ON TIME history doesn’t carry over.

 

  Do not touch any optical block parts, turn table and during replac-

ing. BD laser diode is very sensitive.

1. Preparation
1-1. ESD Countermeasure
It is necessary to confi rm the state of static electricity in the work 
space before the repair is started.
The static electricity resistance of the BD laser is weaker than that 
of the DVD/CD laser.
Do work space and worker’s ESD countermeasures to prevent de-
struction by ESD.

1-2. Jig
•  Digital camera (Recommend with macro mode)
• USB 

memory

• PC
•  Barcode decoder (Refer to “1-3. Barcode decoder 

(BDPRdec_ver3.0)”)

1-3. Barcode decoder (BDPRdec_ver3.0)
Jig name: BDPRdec.exe
Release: 2011.8.25
Version : 3.0.0.0
Software contents:
 

• BDPRdec.exe 

: Barcode decoder software

 • 

SavePath.ini  : 

Decoded 

fi le destination setting fi le (Ini-

tial destination is “C:\BuData.txt”)

 

• TasmanBars.dll  : Decode dll

 

• Uninst.exe 

: Uninstall the “BDPRdec.exe” from PC

Note: When working by OS of the version after VISTA, it is necessary 

to change destination of the decoded fi le to save by UAC function 
(user account function).

 

  In that case, change the description in “SavePath.ini” (default de-

scription is “C:\BuData.txt”) other than C drive.

Install procedure:
1.  Unzip the barcode decoder fi les to any PC folder.
2.  Check the attached 2D code photo (OK_sample.JPG) drag & 

drop onto “BDBUDec.exe”.

 

When the barcode decoder is used for the fi rst time, the pass-
word is necessary. It is unnecessary since the second times.

Note 1: The password will be supplied to only service headquarters, and 

service center name/q’ty/all of software registered information 
should be maintained by service headquarters.

Note 2: Do not change the decoded fi le name “BuData.txt”.

3.  When “.NET frame work requirements” is displayed, down-

load following applications from Microsoft download site.

•  Microsoft .NET Framework Version 2.0 Redistributable Pack-

age (x86) 

 http://www.microsoft.com/downloads/details.aspx?displaylan

g=en&FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5 

•  Microsoft .NET Framework 2.0 Service Pack 1 (x86) 
 http://www.microsoft.com/downloads/details.aspx?displaylan

g=en&FamilyID=79bc3b77-e02c-4ad3-aacf-a7633f706ba5

How to use:
Case 1  Drag & drop 2D code photo onto “BDPRdec.exe”.
Case 2  Drag & drop BU data fi le onto “BDPRdec.exe”.
   Data 

fi le name be changed to specify format and end of 

 

7 character are defi ned.

You can also enter the fi le path at the prompt.

2.  Pass-fail judgment of the optical device KEM480AHA/C2RP1 (OP1)
Perform pass-fail judgment to judge whether the repair of the optical device KEM480AHA/C2RP1 (OP1) is necessary.

Note: Refer to “2-7. OPTICAL DEVICE BLOCK” on page 21 about how to remove the OPTICAL DEVICE BLOCK.

x

o

o

X

o

M

m

±6 mA

±9 mA

1 : 12V

1 : 5V

Note: The photo in fl ow is an image.

Procedure:
1.  Remove the INSULATOR (4 pieces) and broken optical de-

vice KEM480AHA/C2RP1 (OP1) from LOADING ASSY 
(LOM1).

2.  Take photo of the barcode on new optical device KEM480A-

HA/C2RP1 (OP1) bottom side by digital camera.

3.  Assemble the INSULATOR (4 pieces) to new optical device 

KEM480AHA/C2RP1 (OP1), fi x (Torque value: 2 kgf) it to 
LOADING ASSY with screw, and assemble this unit.

4.  Drag & drop the taken photo by step 2 to “BDPRDec.exe”, and 

make the text data (File name: BuData.txt).

5.  Save the text data to USB memory.
6.  Connect USB memory with USB connector on this unit, and 

turn the power on.

7.  Press the [FUNCTION] button on the remote commander to 

select “BD/DVD”.

8.  Press the buttons on the remote commander in order of 

[x] [DISPLAY] [X] [M], and enter the service mode.

9. Press the [m] button on the remote commander to select “[8] 

Drive” and press [ ] button on the remote commander.

10. Repeat the same procedure as 9 to select and execute “[1] 

Drive OP data Write”.

11.  Turn the power off after writing the OP data.
12. Turn the power on, and enter the service mode again.
13. Press the [m] button on the remote commander to select “[8] 

Drive” and press [ ] button on the remote commander.

14. Repeat the same procedure as 13 to select “[7] OP Check 

Menu” then “[3] dIOP”, and the dIOP value is displayed.

15. Confi rm value is the following specifi cation value, and turn the 

power off.

 Specifi cation value:
 BD 

: 

6 mA

 DVD/CD 

: 

9 mA

16. Turn the power on, confi rm playback performance of the BD 

(BLX-104)/DVD (HLX-513)/CD (HLX-A1).

17. Completely assemble this unit, and complete the repair.

CHECKING  METHOD  OF  NETWORK  OPERATION
It is necessary to check the network operation, when replacing the 
complete MB1305 board or WLAN/BT COMBO card. Check the 
operation of wireless and wired LAN, according to the following 
method.

1.  Checking Method of Wireless LAN Operation
Check that access point is recognized surely.

Necessary Equipment:
Wireless access point with router function (AP).

Procedure:
1.  Press the [

?/1

] button to turn the power on.

2.  Press the [HOME] button on the remote commander to enter 

the home menu.

3.  Press the [m]/[M]/[<]/[,] buttons on the remote command-

er to select “Setup”

“Network Settings”, and press the [ ] 

button on the remote commander.

4.  Select “Internet Settings”, and press the [ ] button on the re-

mote commander.

5.  Press the [m]/[M] buttons on the remote commander to select 

“Wireless Setup(built-in)”, and press the [ ] button on the re-
mote commander.

6.  The system starts searching for access points, and displays a 

list of up available network name (SSID).

7.  Check that access point (SSID) is displayed on the searching 

result.

8.  Press the [

?/1

] button to turn the power off.

Note: Refer to the instruction manual about details of the setting method.

2.  Checking method of wired LAN operation
Check that access point is recognized surely.

Procedure:
1.  Connect the main unit to the router or the hub, etc. with the 

LAN cable.

2.  Press the [

?/1

] button to turn the power on.

3.  Press the [HOME] button on the remote commander to enter 

the home menu.

4.  Press the [m]/[M]/[<]/[,] buttons on the remote command-

er to select “Setup”

“Network Settings”, and press the [ ] 

button on the remote commander.

5.  Select “Internet Settings”, and press the [ ] button on the re-

mote commander.

6.  Press the [m]/[M] buttons on the remote commander to select 

“Wired Setup”, and press the [ ] button on the remote com-
mander.

7.  Press the [m]/[M] buttons on the remote commander to select 

“Auto”, and press the [ ] button on the remote commander.

8.  Press the [,] button on the remote commander.

9.  Press the [m]/[M] buttons on the remote commander to select 

“Save & Connect”, and press the [ ] button on the remote 
commander.

10. When “Internet Settings is now complete.” appears, then press 

the [ ] button on the remote commander.

11. Press the [m]/[M] buttons on the remote commander to select 

“Network Connection Diagnostics”, and press the [ ] button 
on the remote commander.

12. Press the [m]/[M] buttons on the remote commander to select 

“IPv4”, and press the [ ] button on the remote commander.

13. Press the [<]/[,] buttons on the remote commander to 

select “Start”, and press the [ ] button on the remote com-
mander.

14. Confi rm that “Network connections are correct” is displayed.
 

(When having confi rmed that “Network connections are cor-
rect” is displayed, advance to the step 20)

15. Press the [ ] button on the remote commander.
16. Press the [m]/[M] buttons on the remote commander to select 

“Network Connection Diagnostics”, and press the [ ] button 
on the remote commander.

17. Press the [m]/[M] buttons on the remote commander to select 

“IPv6”, and press the [ ] button on the remote commander.

18. Press  the  [<]/[,] buttons on the remote commander to 

select “Start”, and press the [ ] button on the remote com-
mander.

19. Confi rm that “Network connections are correct” is displayed.
20. Press the [

?/1

] button to turn the power off.

Note: Refer to the instruction manual about details of the setting method.

TA-SA500WR : Surround amplifi er for HBD-N7200W/N9200W
TA-SA600WR :  Surround amplifi er for HBD-N7200WL/N9200WL
TA-SA700WR : Surround amplifi er for HBD-N5200W

Procedure:
1.  Connect the AC power cord of the main unit.
2.  Press the [

\/1

] button on the main unit to turn the power on.

3.  Connect the AC power cord of the surround amplifi er  (TA-

SA500WR or TA-SA600WR or TA-SA700WR).

4.  When wireless transmission is activated, the [LINK/STAND-

BY] indicator of the surround amplifi er (TA-SA500WR or TA-
SA600WR or TA-SA700WR) turns green.

 

Note: Refer to the operating instructions when the [LINK/STAND-

BY] indicator of the surround amplifi er (TA-SA500WR or TA-
SA600WR or TA-SA700WR) doesn’t light.