Sharp MX-M654N / MX-M754N (serv.man4) Service Manual ▷ View online
MX-M754N Dehumidifying heater kit 2 – 12
(5) Connector connection
1) Remove the screw, and remove the connector cover.
2) Connect the connector and tighten the screw.
I. Installation of the LCC (A3) heater kit
(1) Paper feed unit removal
1) Pull out the paper feed tray.
2) Remove the screw and the cover.
2) Remove the screw and the cover.
3) Open the cover.
4) Remove the screw.
5)
Remove the upper cover.
6)
Disconnect the connector.
7)
Remove the screw and the paper feed unit.
(2) Cover removal
1)
Remove the screw and the cover.
(3) Heater attachment
1)
Attach the heater and fix it with the screw. Attach the connector
to the frame and fix the snap band.
to the frame and fix the snap band.
Ĭ
ĭ
ĭ
Ĭ
ĭ
Ĭ
Ĭ
Ĭ
Ĭ
Ĭ
Ĭ
ĭ
Ĭ
ĭ
Į
į
EX200
MX-M754N Dehumidifying heater kit 2 – 13
2) Attach the protect sheet.
(4) Heater harness unit attachment
1) Attach the snap band of the heater harness unit and fix it with
the screw. While holding the harness upward, attach the AC
cord fixer.
cord fixer.
NOTE: After attaching the snap band, cut and trim the end of
the band.
NOTE: Be careful not to mistake the attaching direction of the
AC cord fixer.
2) Pull the harness tightly in the arrow direction, and check to
confirm that there is no disconnection of the snap band and
that the square hole in the frame is not covered with the har-
ness.
that the square hole in the frame is not covered with the har-
ness.
3) Connect the connector of the heater harness unit. Attach the
earth wire, and fix by the screw.
NOTE: Attach the earth wire at an angle of 45 degrees.
(5) Heater cover and heater sheet attachment
1)
Attach the heater connector cover with the screws (M4 x 8).
2)
Attach the heater cover.
3)
Attach the heater sheet.
(6) Cover attachment
1)
Attach the cover, and fix the screw.
80mm
80mm
2mm
ĭ
Ĭ
ĭ
Į
Ĭ
Ĭ
ĭ
45
c
d45c
EX200
Ĭ
ĭ
Ĭ
ĭ
ĭ
0
᳸1mm
0
᳸1mm
ĭ
ĭ
Ĭ
MX-M754N Dehumidifying heater kit 2 – 14
(7) Paper feed unit attachment
1) Attach the paper feed unit and fix it with the screw.
2) Connect the connector.
3) Attach the upper cover.
4) Fix the screw and close the cover.
5) Attach the cover and fix it with the screw.
6) Insert the paper feed tray.
(8) Connector connection
1)
Remove the screw and the connector cover.
2)
Connect the connector and tighten the screw.
J. Operation check after installation
1)
Turn on the dehumidifier heater switch.
2)
Measure the resistance value between the earth terminal and
the AC terminal (L side), and between the earth terminal and
AC terminal (N side) with the circuit tester, and confirm they
are not short-circuited.
MEMO: For 200V system other than North America, there are
two AC cords. For checking with a tester, use the cord in the
left side when viewed from the rear.
the AC terminal (L side), and between the earth terminal and
AC terminal (N side) with the circuit tester, and confirm they
are not short-circuited.
MEMO: For 200V system other than North America, there are
two AC cords. For checking with a tester, use the cord in the
left side when viewed from the rear.
3)
When not using the heater after checking, turn off the dehu-
midifier heater switch.
midifier heater switch.
Ĭ
ĭ
ĭ
ĭ
ĭ
Ĭ
ĭ
ĭ
Ĭ
MX-M754N MX-LC15 (LARGE CAPACITY TRAY) 3 – 1
MX-M754N
Service Manual
[3] MX-LC15 (LARGE CAPACITY TRAY)
1. Unpacking
A. Packed items check
2. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Release the lock
1) Remove the paper feed desk fixing screw.
NOTE: Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on with-
out removing the fixing screw, a trouble may be resulted.
out removing the fixing screw, a trouble may be resulted.
B. Main unit and large capacity tray unit
connection
1) Attach the mounting plate upper (Packed item No.1) to the
right side of main unit with the fixing screw A (Packed item
No.3). When installing, put the rubber section (
No.3). When installing, put the rubber section (
) of the
mounting plate upper on the lower side.
2)
Remove the right door cover from the machine..
3)
Remove the fixing screws (2 pcs.) of the machine and remove
the cover.
the cover.
4)
Temporarily fix the fixing screw A (Packed item No.3) midway.
5)
Insert the temporarily fixed screw A into the key hole in the
connection unit and temporarily fix the connection unit.
connection unit and temporarily fix the connection unit.
6)
Fix the other fixing screw A and tighten the temporarily fixed
screw A securely.
screw A securely.
No.
Names of bundles
Quantity
1
Mounting plate upper
2
2
Connecting unit
1
3
Fixing screw A (Hex washer S-tight M4x18)
6
4
Fixing screw B (4x8 cup)
1
1
2
3
4
Ĭ
ĭ
Ĭ
ĭ
Ĭ
Ĭ
ĭ
Ĭ
ĭ
ĭ
Ĭ
Click on the first or last page to see other MX-M654N / MX-M754N (serv.man4) service manuals if exist.