Sharp MX-M654N / MX-M754N (serv.man4) Service Manual ▷ View online
MX-M754N MX-M654N/M754N (MAIN UNIT) 1 – 9
5) Press [EXECUTE] key. The printer gray patch image (adjust-
ment pattern) is printed out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
6) Set the gray patch image (adjustment pattern) printed in the
procedure 5) on the document table. Set the gray patch image
(adjustment pattern) printed in the procedure 2) on the docu-
ment table. Place the gray patch image so that the fine lines
are on the left side. At that time, place 5 sheets of white paper
on the printed gray patch image (adjustment pattern).
(adjustment pattern) printed in the procedure 2) on the docu-
ment table. Place the gray patch image so that the fine lines
are on the left side. At that time, place 5 sheets of white paper
on the printed gray patch image (adjustment pattern).
7)
Press [EXECUTE] key.
The printer gray balance adjustment (step 1) is automatically
performed and the gray balance check patch image is printed
out. If there is any streak or unclear print on the printed check
pattern, check the print engine for any problems.
The printer gray balance adjustment (step 1) is automatically
performed and the gray balance check patch image is printed
out. If there is any streak or unclear print on the printed check
pattern, check the print engine for any problems.
8)
The initial setting menu of the halftone image correction is dis-
played. Press [OK] key. The initial setting of the halftone image
correction is performed.
played. Press [OK] key. The initial setting of the halftone image
correction is performed.
9)
Wait until [EXECUTE] key is displayed. When it is displayed,
press it. The halftone image correction is performed.
press it. The halftone image correction is performed.
10) When "COMPLETED THIS PROCEDURE" is displayed, the
adjustment operation is completed.
Cancel SIM46-74.
Cancel SIM46-74.
NOTE: The adjustment result becomes valid only when the
both adjustments in the copy mode and in the printer
mode are completed. For example, if the copy gray
balance adjustment (automatic adjustment) is per-
formed and the simulation is canceled, the adjustment
result is invalid.
mode are completed. For example, if the copy gray
balance adjustment (automatic adjustment) is per-
formed and the simulation is canceled, the adjustment
result is invalid.
11) Check the copy gray balance and density.
12) Check the printer gray balance and density.
12) Check the printer gray balance and density.
(Refer to the item of the printer gray balance and density
check.) If a satisfactory result on the gray balance and the den-
sity is not obtained with the automatic adjustment, execute the
manual adjustment (SIM 67-25) (ADJ 11E (2)). Also when the
service target is selected in procedure 7) to execute the auto-
matic adjustment and a satisfactory result is not obtained, per-
form the manual gray balance adjustment (ADJ 11E (2)). If the
gray balance or density is not in the satisfactory level even
after execution of the automatic and manual adjustments,
there may be another cause. Troubleshoot the cause, repair or
perform necessary works, and repeat the adjustment from the
beginning.
check.) If a satisfactory result on the gray balance and the den-
sity is not obtained with the automatic adjustment, execute the
manual adjustment (SIM 67-25) (ADJ 11E (2)). Also when the
service target is selected in procedure 7) to execute the auto-
matic adjustment and a satisfactory result is not obtained, per-
form the manual gray balance adjustment (ADJ 11E (2)). If the
gray balance or density is not in the satisfactory level even
after execution of the automatic and manual adjustments,
there may be another cause. Troubleshoot the cause, repair or
perform necessary works, and repeat the adjustment from the
beginning.
Q
O P
N
M
L
K
J
I
H
G
F
E
D
C
B
A
Bk
1) Th e max. densit y sectio n is not blurred.
2) Patch A or B is very slightly copied.
3)
Th e patch densit y is identical between patches or not reversed.
Th e patch densit y is change d graduall y.
Th e patch densit y is change d graduall y.
High density
Low density
MX-M754N Dehumidifying heater kit 2 – 1
MX-M754N
Service Manual
[2] Dehumidifying heater kit
1. Parts list
Kit name
Kit part code
No.
Parts name
Part code
Q'ty
Heater electric
component kit
component kit
DKIT-0444FCZZ (100V series)
DKIT-0445FCZZ (200V series)
1
Dehumidifier heater switch
QSW-C9294QCZZ
1
2
Label for heater switch
TLABZ5256FCZZ
1
3
Supporter
LSUPP0140FCPZ
4
4
WH PWB
CPWBF1935FCE1
1
5
WH harness (100V series)
DHAI-5484FCPZ
1
WH harness (200V series)
DHAI-5485FCPZ
1
6
Screw (4×8K)
XBPS740P08K00
1
7
Wire saddle (RLWC-3SV0)
LHLDW1892FCPZ
2
8
Harness clamp (RMS-3V0)
LHLDW1970FCPZ
1
Scanner heater kit
DKIT-0383FCZZ (100V series)
DKIT-0384FCZZ (200V series)
DKIT-0384FCZZ (200V series)
1
Scanner heater (100V series)
RHETP0129FCPZ
1
Scanner heater (200V series)
RHETP0130FCPZ
1
2
Heater fixing plate
LPLTM6923FCZZ
1
3
Band
LBNDJ0013FCZ1
2
4
Clamp (YMC-05-0)
LHLDW7011XCZZ
5
5
Screw(3×4)
LX-BZ1041FCZZ
2
6
Screw(4×6)
XHBS740P06000
1
7
Snap band
LBNDJ0043FCZZ
1
Tandem heater kit
DKIT-0395FCZZ (100V series)
DKIT-0396FCZZ(200V series)
1
Tandem heater (100V series)
RHETP0140FCPZ
1
Tandem heater (200V series)
RHETP0142FCPZ
1
2
Heater fixing plate
LPLTM6089FCZ2
1
3
Heater cover
PCOVP1654FCZ2
1
4
Edge holder
LHLDW1285FCZZ
1
5
Heater harness sheet
PSHEZ5135FCZZ
1
6
Heater cover sheet
PSHEZ5012FCZZ
1
7
Step screw (M3)
LX-BZ0987FCZZ
1
8
Screw (M4x6 S-tight)
XHBS740P06000
1
9
Screw (M3x8 S-tight)
XHBS730P08000
3
10
High temperature warning label
TLABZ5459FCZZ
1
Cassette heater kit
(R)
(R)
DKIT-0393FCZZ(100V series)
DKIT-0394FCZZ(200V series)
1
Cassette heater (100V series)
RHETP0141FCPZ
1
Cassette heater (200V series)
RHETP0143FCPZ
1
2
Heater fixing plate
LPLTM6089FCZ2
1
3
Heater cover
PCOVP1654FCZ2
1
4
High temperature warning label
TCAUH1035FCZZ
1
5
Step screw (M3)
LX-BZ1134FCPZ
1
6
Screw (M3x8 S-tight)
XHBS730P08000
4
Cassette heater kit
(L)
(L)
DKIT-0446FCZZ (100V series)
DKIT-0441FCZZ (200V series)
1
Cassette heater (100V series)
RHETP0141FCPZ
1
Cassette heater (200V series)
RHETP0143FCPZ
1
2
Heater fixing plate
LPLTM6089FCZ2
1
3
Heater cover
PCOVP1654FCZ2
1
4
Heater harness sheet
PSHEZ5135FCZZ
1
5
High temperature warning label
TCAUH1035FCZZ
1
6
Step screw (M3)
LX-BZ1134FCPZ
1
7
Screw (M3x8 S-tight)
XHBS730P08000
4
LCC (A4) heater kit
DKIT-0451FCZZ (100V series)
DKIT-0451FC11 (200V series)
1
Heater harness (100V series)
DHAI-5504FCPZ
1
Heater harness (200V series)
DHAI-5505FCPZ
1
2
Snap band
LBNDJ0043FCP1
1
3
AC cord fixer
LFIX-0016FCZZ
1
4
Protect sheet
PFLT-0067FCP1
1
5
Connector cover A
PCOVP2149FCZZ
1
6
Connector cover B
PCOVP2150FCZZ
1
7
Heater (100V series)
RHETP0145FCZZ
1
Heater (200V series)
RHETP0121FCZZ
1
8
Screw (M4 x 8K)
XBPS740P08K00
1
9
Screw (M3 x 4)
XHBS730P04000
1
10
Screw for EL connector
LX-BZ1119FCZZ
1
11
Screw (M4 x 28K)
XBPS740P28KS0
2
12
Screw (M3 x 20)
XBBS730P20000
3
13
Screw (M4 x 8)
XHBS740P08000
1
14
Nut (M3 = 2.4)
XNES730-24000
3
1
: ‘14/Dec
1
1
1
1
1
1
1
5
: ‘16/Apr
5
5
MX-M754N Dehumidifying heater kit 2 – 2
LCC (A3) heater kit
DKIT-0452FCZZ (100V series)
DKIT-0452FC11 (200V series)
1
Heater harness (100V series)
DHAI-5506FCPZ
1
Heater harness (200V series)
DHAI-5507FCPZ
1
2
Snap band
LBNDJ0043FCP1
1
3
AC cord fixer
LFIX-0016FCZZ
1
4
Heater cover
PCOVP1942FCZZ
1
5
Heater sheet
PSHEZ5482FCZZ
1
6
Connector cover A
PCOVP2149FCZZ
1
7
Connector cover B
PCOVP2150FCZZ
1
8
Heater (100V series)
RHETP0145FCZZ
1
Heater (200V series)
RHETP0121FCZZ
1
9
Screw (M4 x 8K)
XBPS740P08K00
1
10
Screw (M3 x 4)
XHBS730P04000
1
11
Screw (M4 x 8 Round-tipped S-tight)
LX-BZ0941FCPZ
2
12
Screw for EL connector
LX-BZ1119FCZZ
1
13
Screw (M4 x 28K)
XBPS740P28KS0
2
14
Screw (M3 x 20)
XBBS730P20000
3
15
Screw (M4 x 8)
XHBS740P08000
2
16
Nut (M3 = 2.4)
XNES730-24000
3
17
Connector cover
PCOVP2658FCZZ
1
18
Protect sheet
PFLT-0067FCP1
1
Kit name
Kit part code
No.
Parts name
Part code
Q'ty
MX-M754N Dehumidifying heater kit 2 – 3
2. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Remove the rear cabinet
1) Loosen the screw at the bottom of the rear cabinet. Remove
the screw, and remove the rear cabinet.
B. Installation of the heater electric component
kit
(1) Attach the dehumidifier heater switch
1) Remove the screw, and remove the connector cover B.
2) Remove the screw, and remove the left cabinet rear.
3)
Remove the screw, and remove the left cabinet lower.
4)
Attach the dehumidifier heater switch to the frame.
NOTE: Install the dehumidifier heater switch so that the side
of the mounting terminal post is the inward side of the
main unit.
main unit.
5)
Cut the switch part of the left cabinet lower.
Attach the label for dehumidifier heater switch to the left cabi-
net lower.
Attach the label for dehumidifier heater switch to the left cabi-
net lower.
NOTE: Be careful not to damage the cabinet.
NOTE: Wipe the surface where the label is to be affixed with
alcohol, then attach the label along the concave on left
cabinet lower.
cabinet lower.
6)
Attach the left cabinet lower, and fix by the screw.
Ĭ
ĭ
Ĭ
Ĭ
Į
Į
Į
Į
Į
Į
Į
Į
Į
Į
į
① Screw(4×8)
③ Screw(4×6)
③ Screw(4×6)
2
1
2
1
Dehumidifier heater switch
1
22
1
1
: ‘14/Dec
1
1
Click on the first or last page to see other MX-M654N / MX-M754N (serv.man4) service manuals if exist.