Sharp MX-M654N / MX-M754N (serv.man4) Service Manual ▷ View online
MX-M754N Dehumidifying heater kit 2 – 8
2) Pass the heater harness through the hole on the rear frame,
and fix by the snap band to the frame.
3) Connect the connector of heater harness and WH harness.
F. Installation of the cassette heater kit (L)
(1) Assembling of the cassette heater
1) Attach the cassette heater to the heater mount plate, and fix by
the screw (M3 x 8 S-tight).
NOTE: Be careful of the direction of each part.
Align the directions of the heater mount plate and the
dehumidifier heater with the pawls.
dehumidifier heater with the pawls.
2)
Affix the heater harness onto the heater cover.
3)
Attach the heater mount plate to the heater cover, and fix by
the screw (M3 x 8 S-tight).
the screw (M3 x 8 S-tight).
NOTE: Pull out the heater harness to the area which the
heater harness sheet is attached to.
4)
Affix the high temperature warning label onto the heater cover.
(2) Installation of the cassette heater unit
1)
Attach the step screw (M3) to the frame.
Put the cassette heater unit on the step screw (M3) and fix it
with the tight screw (M3 x 8 S-tight).
Put the cassette heater unit on the step screw (M3) and fix it
with the tight screw (M3 x 8 S-tight).
2)
Pass the heater harness through the hole on the rear frame,
and fix by the snap band to the frame.
and fix by the snap band to the frame.
1
2
2
1
Heater cover
M3 x 8 S-tight
M3 x 8 S-tight
M3 x 8 S-tight
Pawl
Pawl
Dehumidifier
heater
heater
Harness
Heater mount
plate
plate
2
1
2
1
3
2
1
2
MX-M754N Dehumidifying heater kit 2 – 9
3) Remove the harness front the wire saddle.
Connect the connector of heater harness and WH harness.
4) Attach the tray 3 and tray 4.
G. Attach the rear cabinet
1) Attach the rear cabinet, and fix by the screw. Tighten the screw
at the bottom of the rear cabinet.
H. Installation of the LCC (A4) heater kit
(1) Paper feed unit removal
1)
Pull out the paper feed tray.
2)
Open the cover. Remove the cover and the screws.
3)
Open the screw.
4)
Open the tray.
5)
Open the upper cover.
į
į
į
ĭ
ĭ
ĭ
ĭ
ĭ
ĭ
ĭ
ĭ
ĭ
ĭ
Ĭ
Į
Ĭ
ĭ
Ĭ
ĭ
Į
MX-M754N Dehumidifying heater kit 2 – 10
6) Disconnect the connector.
7) Remove the paper feed unit.
8) Remove the screw and the heater cover.
9) Remove the screws and the cover.
(2) Heater attachment
1)
Attach the heater and fix it by the screw. Attach the connector
to the frame, and fix the snap band.
to the frame, and fix the snap band.
2)
Attach the protect sheet.
(3) Heater harness unit attachment
1)
Attach the snap band of the heater harness unit, and fix by the
screw. While holding the harness upward, attach the AC cord
fixer.
screw. While holding the harness upward, attach the AC cord
fixer.
NOTE: After attaching the snap band, cut and trim the end of
the band.
NOTE: Be careful not to mistake the attaching direction of the
AC cord fixer.
2)
Pull the harness tightly in the arrow direction, and check to
confirm that there is no disconnection of the snap band and
that the square hole in the frame is not covered with the har-
ness.
confirm that there is no disconnection of the snap band and
that the square hole in the frame is not covered with the har-
ness.
ĭ
Ĭ
Ĭ
Ĭ
ĭ
Ĭ
Ĭ
ĭ
Ĭ
ĭ
Į
į
EX200
75
d5mm
0
᳸2mm
Ĭ
ĭ
Į
į
MX-M754N Dehumidifying heater kit 2 – 11
3) Connect the connector of the heater harness unit. Attach the
earth wire, and fix by the screw.
NOTE: Attach the earth wire at an angle of 45 degrees.
(4) Paper feed unit attachment
1) Attach the cover and fix it with the screw.
2) Attach the heater cover and fix it with the screw.
3)
Attach the paper feed unit and fix it with the screw.
4)
Connect the connector.
5)
Attach the upper cover.
6)
Fix the upper cover with the screw.
7)
Close the cover and fix it with screw.
8)
Close the paper feed tray.
Ĭ
ĭ
Į
45
c
d45c
EX200
ĭ
ĭ
Ĭ
ĭ
Ĭ
Ĭ
ĭ
ĭ
Į
ĭ
Į
ĭ
Ĭ
Click on the first or last page to see other MX-M654N / MX-M754N (serv.man4) service manuals if exist.