Sharp MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) Service Manual ▷ View online
MX-M503N MX-FN11 9 – 4
4)
Remove the reverse tray.
5)
Remove the screws, and remove the interface left cabinet.
6)
Remove the screws, and remove the paper pass latch recep-
tion parts and the positioning pin.
tion parts and the positioning pin.
D. Attaching the mylar
1)
Attach the mylar (package part No.13) to the position indicated
in the figure.
in the figure.
E. Installation of the connection fixture F/R
1)
Install the connection fixture R (Package part No. 8) to the
main unit with the fixing screws (Package part No. 3).
main unit with the fixing screws (Package part No. 3).
2)
Install the connection fixture F (Package part No. 7) to the
main unit with the fixing screws (Package part No. 3).
main unit with the fixing screws (Package part No. 3).
Corner
reference
reference
Corner
reference
reference
Reference
Reference
MX-M503N MX-FN11 9 – 5
F. Attaching the cushion
1)
Attach the cushion (S) (package part No.14), the cushion (M)
(package part No.15) and the cushion (L) (package part No.16)
to the position indicated in the figure.
(package part No.15) and the cushion (L) (package part No.16)
to the position indicated in the figure.
G. Check of the connected position of main unit
and finisher
1)
Insert the rail of the finisher into the slit on the rail reception
sheet metal of the main unit, install the finisher.
sheet metal of the main unit, install the finisher.
2)
Remove the screw, and remove the connector cover on rear
side of the finisher.
side of the finisher.
3)
Check that the center of the screw hole of the finisher is in the
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
* When not the range of specification, progress to the proce-
dure of "H. Adjustment".
If the adjustment is not required, remove the screws from
the screw hole directly and push the caster into it until the
installation fixing.
If the adjustment is not required, remove the screws from
the screw hole directly and push the caster into it until the
installation fixing.
H. Adjustment
1)
Remove the finisher from the main unit.
Reference
Cushion (M)
Reference
Reference
Refer-
ence
Refer-
ence
Refer-
ence
Cushion (L)
Cushion (S)
MX-M503N MX-FN11 9 – 6
2)
Remove the screw, slide to the left the front lower cover, and
remove it.
remove it.
3)
Open the front upper door, and remove the screw.
4)
Remove the screws, and open the front cover.
5)
Remove the fixing tapes.
6)
Remove the screws, and remove the auxiliary wheels.
7)
Remove the screws, and remove the rear lower cover.
8)
Remove the fixing tapes.
MX-M503N MX-FN11 9 – 7
9)
Loosen both of the caster fixing screws of the front side and
rear side.
rear side.
10) Remove the screw, and remove the spanner installed inside
the front lower door.
11) Turn the bolt for which the adjustment is necessary, and adjust
to become it within the range of specification.
12) Check to insure that the upper and lower clearances between
the main unit and the finisher are even.
Click on the first or last page to see other MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) service manuals if exist.